Home › Engine / Hybrid System › M15A-FKS (ENGINE MECHANICAL) › ENGINE UNIT › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _087837 M15A-FKS ENGINE MECHANICAL _0424630 ENGINE UNIT A

M15A-FKS ENGINE MECHANICAL  ENGINE UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION


PROCEDURE

Hide 1.INSTALL WIRE HARNESS CLAMP BRACKET

a.

Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 16281 2.INSTALL NO. 4 WATER BY-PASS HOSE

a.

Install the No. 4 water by-pass hose to the water outlet and slide the clip to secure it.


b.

Engage the clamp.


Hide 11452D 3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

a.

Apply a light coat of engine oil to a new O-ring.


b.

Install the O-ring to the engine oil level dipstick guide.


c.

Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


d.

Install the engine oil level dipstick.


Hide 23250 5.INSTALL FUEL INJECTOR ASSEMBLY

Hide 82126A 6.INSTALL NO. 6 ENGINE WIRE

a.

Engage the clamp.


b.

Connect the 3 connectors.


Hide 82219C 7.INSTALL SENSOR WIRE

a.

Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


b.

Engage the 2 clamps.


c.

Connect the 4 connectors.


Hide 8.INSTALL WATER BY-PASS PIPE ASSEMBLY

a.

Install the water by-pass hose assembly to the water inlet with thermostat sub-assembly and cylinder head sub-assembly and slide the 2 clips to secure them.


b.

Install the bolt.

Torque:
21 N*m (214 kgf*cm, 15 ft.*lbf)


Hide 23100X 9.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)

Hide 23802B 10.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY

a.

Install the No. 2 fuel pipe sub-assembly to the camshaft housing sub-assembly with the 2 bolts.

Torque:
28.5 N*m (291 kgf*cm, 21 ft.*lbf)


Hide 23902 11.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY

a.

Connect the No. 2 fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


b.

Install the fuel pipe clamp to the fuel tube connector.


Hide 23901 12.INSTALL FUEL TUBE SUB-ASSEMBLY

a.

Connect the fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 17177 13.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET

Hide 25624 15.INSTALL EGR VALVE ADAPTER

a.

Engage the guide.


b.

Using an 8 mm socket wrench, install the EGR valve adapter with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 25601 16.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY

Hide 12262 18.INSTALL NO. 2 VENTILATION HOSE

a.

Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.


Hide 23820 19.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY

a.

Engage the clamp.


b.

Install the fuel vapor feed hose assembly to the purge valve.


Hide 22271 20.INSTALL THROTTLE BODY GASKET

Hide 22030 21.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY

Hide 17167 24.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR