Home › Drivetrain › CLUTCH › CLUTCH PEDAL › 2020.03–2020.07
RM36W0E _52 Drivetrain _089426 CLUTCH _0424691 CLUTCH PEDAL A

CLUTCH  CLUTCH PEDAL  INSTALLATION  


PROCEDURE

Hide 31321 1.INSTALL CLUTCH PEDAL PAD

a.

Install the clutch pedal pad to the clutch pedal sub-assembly.


Hide 31453B 2.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS BUSHING

a.

Install a new clutch master cylinder push rod clevis bushing to the clutch pedal sub-assembly.

NOTICE:

Install the clutch master cylinder push rod clevis bushing from the left side of the vehicle.



b.
C434805C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch master cylinder push rod clevis bushing.


Hide 31324A 3.INSTALL CLUTCH PEDAL SHAFT COLLAR

a.

Install the clutch pedal shaft collar to the clutch pedal sub-assembly.


b.
C431230C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to both sides of 2 new clutch pedal bushings.


c.

Install the 2 clutch pedal bushings to the clutch pedal sub-assembly.


Hide 31301P 4.INSTALL CLUTCH PEDAL TURNOVER BUSH

a.
C431231C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the inside of the clutch pedal turnover bushing.


b.

Install the clutch pedal turnover bushing to the clutch pedal sub-assembly.


Hide 31353 5.INSTALL CLUTCH PEDAL SPRING HOLDER

a.
C431232C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the contact surface of the clutch pedal spring holder.


b.

Install the clutch pedal spring holder to the clutch pedal support sub-assembly.


Hide 31301 6.INSTALL CLUTCH PEDAL SUB-ASSEMBLY

a.

Install the clutch pedal sub-assembly to the clutch pedal support sub-assembly with the bolt.

Torque:
36.8 N*m (375 kgf*cm, 27 ft.*lbf)

NOTICE:
·

Install the bolt from the right side of the vehicle.

·

Turn the nut while holding the bolt.




Hide 31301A 7.INSTALL CLUTCH PEDAL SPRING

a.

Move the clutch pedal sub-assembly to the full stroke position.


b.

Install the clutch pedal spring to the clutch pedal sub-assembly and clutch pedal bracket sub-assembly.


Hide 88280A 8.INSTALL CLUTCH SWITCH ASSEMBLY

Hide 9.INSTALL CLUTCH PEDAL SUPPORT ASSEMBLY

a.

Install the clutch pedal support assembly to the vehicle body with the 4 nuts.

Torque:
12.7 N*m (130 kgf*cm, 9 ft.*lbf)


b.

Engage the 2 clamps to connect the wire harness to the clutch pedal support assembly.


c.

Connect the clutch start switch assembly connector.


d.

Connect the clutch switch assembly connector.


Hide 31453A 10.INSTALL CLUTCH MASTER CYLINDER PUSH ROD CLEVIS WITH HOLE PIN

a.
C431233C01
0,0 0,0 false
V100135

MP Grease


Apply MP grease to the clevis pin.


b.

Connect the clutch master cylinder assembly to the clutch pedal sub-assembly with the master cylinder push rod clevis with hole pin.

NOTICE:

Install the clevis pin from the left side of the vehicle.



c.

Install a new clip to the master cylinder push rod clevis with hole pin.


Hide 84520 11.INSTALL CLUTCH START SWITCH ASSEMBLY

Hide 12.INSTALL STEERING COLUMN ASSEMBLY

Hide 13.INSPECT CLUTCH PEDAL

Hide 88280A 14.INSPECT CLUTCH SWITCH ASSEMBLY

Hide 15. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART