Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY › 2020.03–2020.07
RM36W0E _55 Steering _087550 STEERING COLUMN _0424130 STEERING COLUMN ASSEMBLY A

STEERING COLUMN  STEERING COLUMN ASSEMBLY  INSTALLATION  


PROCEDURE

Hide 1.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 2.INSTALL STEERING COLUMN ASSEMBLY

NOTICE:

Make sure that the wire harness is not interfering with the steering column assembly.


a.

Install the steering column assembly with the bolt and 2 nuts.

Torque:
36 N*m (367 kgf*cm, 27 ft.*lbf)

NOTICE:
·

After the column is installed, check the tilt operation.

·

If a large amount of force is required to operate the tilt mechanism or abnormal noise occurs, loosen the nuts and move the bracket forward or backward until the tilt operation works smoothly.

Tighten the nuts and check the tilt operation again.




b.

Connect each connector and engage each wire harness clamp to the steering column assembly.


Hide 45260 3.INSTALL NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C434159C01
2.24,0.448 1.521,0.448 true 1.542,0.51 1.781,0.51 1.781,0.51 1.781,0.458 true 2.271,0.344 2.479,0.531 0.208,0.188 10 true *a
*a Matchmark
V113147

Install in this direction


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering column assembly.


b.

Install the No. 2 steering intermediate shaft assembly to the steering column assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45260 4.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

a.
C434160C01
1.542,1.5 2.448,1.5 true 1.531,1.563 1.906,1.563 1.906,1.563 1.906,1.5 true 2.51,1.406 2.729,1.604 0.219,0.198 10 true *a
*a Matchmark
V113147

Connect in this direction


Align the matchmarks on the No. 2 steering intermediate shaft assembly and steering gear assembly.


b.

Connect the No. 2 steering intermediate shaft assembly to the steering gear assembly.


c.

Install the bolt.

Torque:
64 N*m (653 kgf*cm, 47 ft.*lbf)


Hide 45259A 5.INSTALL COLUMN HOLE COVER SILENCER SHEET

a.

Disengage the 2 clips to install the column hole cover silencer sheet.


Hide 84340 7.INSTALL STOP LIGHT SWITCH ASSEMBLY

Hide 55480D 8.INSTALL LOWER INSTRUMENT PANEL FINISH PANEL ASSEMBLY

Hide 53601 9.INSTALL HOOD LOCK CONTROL LEVER SUB-ASSEMBLY

Hide 55317E 10.INSTALL NO. 1 INSTRUMENT SIDE PANEL

Hide 62311B 11.INSTALL FRONT DOOR OPENING TRIM WEATHERSTRIP RH

Hide 55606 12.INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY

Hide 62111C 13.INSTALL COWL SIDE TRIM BOARD RH

Hide 67913B 14.INSTALL FRONT DOOR SCUFF PLATE RH

Hide 58802E 15.INSTALL FRONT CONSOLE BOX SUB-ASSEMBLY

Hide 16.INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
·

Do not replace the spiral cable with sensor sub-assembly with the auxiliary battery connected and the ignition switch ON.

·

Do not rotate the spiral cable with sensor sub-assembly without the steering wheel assembly installed, with the auxiliary battery connected and the ignition switch ON.

·

Ensure that the steering wheel assembly is installed and aligned straight when inspecting the steering sensor.



a.
C435733C01
1.094,0.542 1.375,0.542 false 0.938,0.448 1.25,0.604 0.313,0.156 10 false *a
*a Clamp


Using pliers, expand the clamp.


b.

While holding the clamp expanded, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and engage the claw.


c.

Return the clamp to its original position.


d.

Connect each connector to the turn signal switch assembly with spiral cable sub-assembly.


Hide 45286B 17.INSTALL UPPER STEERING COLUMN COVER

a.

Engage the claw to install the upper steering column cover.


Hide 45287 18.INSTALL LOWER STEERING COLUMN COVER

a.

Engage the 2 claws to install the lower steering column cover.


b.

Install the 3 screws.


Hide 19.ALIGN FRONT WHEELS FACING STRAIGHT AHEAD

Hide 20.ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

Hide 45100 21.INSTALL STEERING WHEEL ASSEMBLY

Hide 22.CHECK STEERING WHEEL CENTER POINT

Hide 45130 23.INSTALL HORN BUTTON ASSEMBLY

Hide 24. PERFORM POWER STEERING ECU INITIAL SETTING