Home › Drivetrain › CLUTCH › CLUTCH UNIT › 2020.03–2020.07
RM36W0E _52 Drivetrain _089426 CLUTCH _0424693 CLUTCH UNIT A

CLUTCH  CLUTCH UNIT  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release cylinder with bearing assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release cylinder with bearing assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release cylinder with bearing assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 31250 1.INSTALL CLUTCH DISC ASSEMBLY

C293452C03
2.281,1.615 2.74,1.615 false 1.76,3.521 2.135,3.833 false 0.635,2.333 1.052,2.521 false 1.344,2.646 1.771,2.344 false 1.813,2.26 2.125,2.417 0.313,0.156 10 false *1 0.479,2.25 0.792,2.406 0.313,0.156 10 false *2 2.781,1.531 3.24,1.729 0.458,0.198 10 false SST 2.188,3.76 2.646,3.958 0.458,0.198 10 false SST 0.688,3.302 1,3.458 0.313,0.156 10 false *a
*1 Clutch Disc Assembly
*2 Flywheel Sub-assembly
*a Flywheel Sub-assembly Side


a.

Insert SST into the clutch disc assembly, then insert them both into the flywheel sub-assembly.

SST
09301-00210  

NOTICE:
·

Keep the lined part of the clutch disc assembly, the pressure plate, and the surface of the flywheel sub-assembly away from oil and foreign matter.

·

Insert the clutch disc assembly in the correct direction.




Hide 31210 2.INSTALL CLUTCH COVER ASSEMBLY

a.
C401475C01
1.115,0.75 0.385,0.99 0.385,0.99 1.063,0.719 true 2.021,1.104 2.448,1.469 2.448,1.469 2.604,1.469 true 0.188,0.927 0.5,1.083 0.313,0.156 10 false *a 2.333,0.146 3.031,0.406 0.698,0.26 10 false 1 (*b), 4 2.396,1.802 2.667,1.979 0.271,0.177 10 false 2 0.563,1.073 0.76,1.302 0.198,0.229 10 false 3 1.083,1.927 1.25,2.135 0.167,0.208 10 false 6 0.979,0.156 1.135,0.354 0.156,0.198 10 false 7 2.771,0.948 2.927,1.146 0.156,0.198 10 false 5 2.667,1.385 3.021,1.625 0.354,0.24 10 false SST
*a Matchmark
*b Temporarily Tighten


Align the matchmark on the clutch cover assembly with the one on the flywheel sub-assembly.


b.

Following the procedure shown in the illustration, tighten the 6 bolts in order, starting with the bolt located near the knock pin at the top.

SST
09301-00210  

Torque:
19.1 N*m (195 kgf*cm, 14 ft.*lbf)

HINT:
·

Following the order in the illustration, tighten the bolts evenly one at a time.

·

Move SST up and down, right and left lightly after checking that the clutch disc assembly is in the center, and tighten the bolts.




Hide 31210 3.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

a.
C283240

Using a dial indicator with a roller instrument, check the diaphragm spring tip alignment.

Maximum Non-alignment:

0.5 mm (0.0197 in.)



b.
C283241N02
2.344,1.25 2.583,0.833 2.583,0.833 2.75,0.833 false 2.802,0.76 3.26,0.958 0.458,0.198 10 true SST

If the alignment is not as specified, using SST, adjust the diaphragm spring tip alignment.

SST
09333-00013  


Hide 31400 4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

a.
C401477

Temporarily tighten the clutch release cylinder to bleeder tube to a new clutch release cylinder with bearing assembly.

NOTICE:

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder to bleeder tube from the connecting part.



b.

Clean and degrease all installation surfaces for the clutch release cylinder with bearing assembly.


c.

Install the clutch release cylinder with bearing assembly with 3 new bolts.

Torque:
22.5 N*m (229 kgf*cm, 17 ft.*lbf)

NOTICE:
·

The clutch release cylinder with bearing assembly and installation bolts cannot be reused and must be replaced with new ones.

·

Clean and degrease all installation surfaces and make sure that the clutch release cylinder with bearing assembly fits securely with the manual transaxle assembly during installation. The first bolt should be tightened by hand while holding the clutch release cylinder with bearing assembly.

·

Ensure that none of the clutch spline grease adheres to the clutch release cylinder with bearing assembly.

·

The clutch release cylinder with bearing assembly cannot be disassembled.




d.

Install the clutch tube boot onto the manual transaxle assembly.


e.
C431529

Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.


f.

Temporarily tighten the 2 bolts and install the clutch release bleeder sub-assembly.


g.
C431530C01
2.656,0.24 2.854,0.438 0.198,0.198 10 true *a
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube to the clutch release cylinder with bearing assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:

Do not kink or damage the clutch release cylinder to bleeder tube.


HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




h.
C434813C01
0,0 0,0 false
V100135

Clutch Spline Grease


Apply clutch spline grease to the input shaft splines.

Grease:

Toyota Genuine Clutch Spline Grease or equivalent



Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C431529

Separate the clutch release cylinder to bleeder tube from the clutch release bleeder sub-assembly.


b.

Remove the 2 bolts and clutch release bleeder sub-assembly.


Hide 6.INSPECT CLUTCH PIPE LINE

C431532

a.

Using SST, apply pressure of 100 kPa (1.0 kgf/cm2, 15 psi) to the clutch pipe location shown in the illustration and confirm that pressure is maintained for 15 seconds or more.

SST
09992-00242  

If the pressure drops, replace the clutch release cylinder to bleeder tube.


Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

a.
C431529

Temporarily tighten the clutch release cylinder to bleeder tube to the clutch release bleeder sub-assembly.


b.

Install the 2 bolts and clutch release bleeder sub-assembly.

Torque:
16.7 N*m (170 kgf*cm, 12 ft.*lbf)


c.
C434814C01
0,0 0,0 false
*a Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the clutch release cylinder to bleeder tube.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the clutch release cylinder to bleeder tube.

·

Do not allow any foreign matter such as dirt or dust to enter the clutch release cylinder to bleeder tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 31483 8.INSTALL BLEEDER CLUTCH RELEASE TUBE

a.

Install the clamp to the bleeder clutch release tube.


b.

Temporarily tighten the bleeder clutch release tube to the clutch release bleeder sub-assembly.


c.

Install the bleeder clutch release tube to the manual transaxle assembly with the bolt.

Torque:
12 N*m (122 kgf*cm, 9 ft.*lbf)


d.
C434815C01
0,0 0,0 false
V100135

Torque Wrench Fulcrum Length


Using a 10 mm union nut wrench, install the bleeder clutch release tube to the clutch release bleeder sub-assembly.

Torque:
Specified Tightening Torque : 15.2 N*m (155 kgf*cm, 11 ft.*lbf)

NOTICE:
·

Do not kink or damage the bleeder clutch release tube.

·

Do not allow any foreign matter such as dirt or dust to enter the bleeder clutch release tube from the connecting part.



HINT:
·

Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION

·

When using a union nut wrench (fulcrum length of 22 mm (0.866 in.)) + torque wrench (fulcrum length of 162 mm (6.38 in.)):

13.4 N*m (137 kgf*cm, 10 ft.*lbf)




Hide 30300 9.INSTALL MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge)

Hide 30300 10.INSTALL MANUAL TRANSAXLE ASSEMBLY (When Using the Engine Support Bridge)

Hide 11. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART