Home › Drivetrain › EC6E (MANUAL TRANSMISSION / TRANSAXLE) › MANUAL TRANSAXLE ASSEMBLY (When Not Using the Engine Support Bridge) › 2020.03–2020.07
RM36W0E _52 Drivetrain _089427 EC6E MANUAL TRANSMISSION / TRANSAXLE _0424705 MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge) A

EC6E MANUAL TRANSMISSION / TRANSAXLE  MANUAL TRANSAXLE ASSEMBLY(When Not Using the Engine Support Bridge)  INSTALLATION  


CAUTION / NOTICE / HINT

NOTICE:

When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.


PROCEDURE

Hide 35150D 1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY

HINT:

Perform this procedure only when replacement of the manual transaxle assembly is necessary.


a.
C435448

Coat the O-ring of a new transmission case plug assembly with gear oil.


b.
C435447

Install the transmission case plug assembly to the front transaxle case.


Hide 2.INSTALL WIRE HARNESS CLAMP BRACKET

a.
C435445

Install the wire harness clamp bracket to the manual transmission case with the bolt.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


b.
C435446

Install the wire harness clamp brackets to the front transaxle (MTM) case with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 87121V 3.INSTALL HEATER BRACKET

a.

Install the heater bracket to the manual transmission case with the bolt.

Torque:
14 N*m (143 kgf*cm, 10 ft.*lbf)


Hide 31400 4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY

Hide 31407B 5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 6.INSPECT CLUTCH PIPE LINE

Hide 31407B 7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY

Hide 31484 8.INSTALL CLUTCH FLEXIBLE HOSE BRACKET

a.

Install the clutch flexible hose bracket to the manual transmission case with the bolt.

Torque:
19 N*m (194 kgf*cm, 14 ft.*lbf)


Hide 31483 9.INSTALL BLEEDER CLUTCH RELEASE TUBE

Hide 12364B 10.INSTALL NO. 2 ENGINE MOVING CONTROL ROD

a.
C435454

Install the No. 2 engine moving control rod to the front transaxle case with the 4 bolts in the order shown in the illustration.

Torque:
44 N*m (449 kgf*cm, 32 ft.*lbf)


Hide 51201 11.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

a.

Install the front suspension crossmember sub-assembly to the No. 2 engine moving control rod with the bolt.

Torque:
170 N*m (1734 kgf*cm, 125 ft.*lbf)


Hide 30300 12.INSTALL MANUAL TRANSAXLE ASSEMBLY

a.
C435449C01
0.417,1.083 1.135,0.823 true 2.24,0.615 2.573,1.104 true 0.271,1.01 0.583,1.208 0.313,0.198 10 false *1 2.615,1.094 2.927,1.292 0.313,0.198 10 false *1
*1 Knock Pin


Check that the 2 knock pins are installed on the engine assembly before installing the manual transaxle assembly.


b.

Align the input shaft with the clutch disc and install the engine assembly to the manual transaxle assembly.

NOTICE:
·

Make sure that the wire harness or similar items are not pinched between the contact surfaces.

·

Do not forcibly pry on the manual transaxle assembly when installing it to the engine assembly.

·

Do not apply excessive force to the manual transaxle assembly as this will break the input shaft.

·

Make sure that the knock pins fit securely into the holes when installing the manual transaxle assembly to the engine assembly.

·

Make sure that the contact surfaces of the engine assembly and manual transaxle assembly are flat against each other before tightening the bolts.




c.
C435451N01
1.865,0 2.104,0.25 0.24,0.25 10 false B 1.26,0.083 1.479,0.365 0.219,0.281 10 false A 2.438,1.875 2.656,2.042 0.219,0.167 10 false C

Temporarily install the bolt (A).

HINT:

Bolt (A): Install from the manual transaxle assembly side.



d.

Install the bolt (B), then fully tighten the bolt (A).

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)

HINT:

Bolt (B): Install from the manual transaxle assembly side.



e.

Install the bolts (C).

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)

HINT:

Bolt (C): Install from the manual transaxle assembly side.



f.
C435452N01
0.813,0.917 0.969,1.115 0.156,0.198 10 true D 1.156,1.688 1.313,1.885 0.156,0.198 10 true D 1.594,1.979 1.75,2.177 0.156,0.198 10 true D 2.719,1.385 2.875,1.583 0.156,0.198 10 true D

Install the 4 bolts (D).

Torque:
46 N*m (469 kgf*cm, 34 ft.*lbf)

HINT:

Bolt (D): Install from the engine assembly side.



Hide 12321B 13.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

a.
C435437C01
2.802,0.531 3.427,0.74 0.625,0.208 10 true 1 (*a), 3 0.365,0.479 0.563,0.719 0.198,0.24 10 true 2
*a Temporarily Tighten


Install the drive shaft heat insulator sub-assembly to the manual transmission case with the 2 bolts in the order shown in the illustration.

Torque:
17.6 N*m (179 kgf*cm, 13 ft.*lbf)


Hide 14.CONNECT ENGINE WIRE

a.
C435435

Engage the 3 clamps.


b.
C435434

Engage the 3 clamps.


c.
C435433C02
1.802,0.604 2.052,0.813 0.25,0.208 10 true *a
*a Neutral Position Switch Connector


Connect the neutral position switch connector.


d.
C435432

Engage the 3 clamps.


e.

Install the 3 bolts.

Torque:
20 N*m (204 kgf*cm, 15 ft.*lbf)


f.
C435430

Engage the clamp.


g.
C435431C02
2.146,0.938 2.365,1.125 0.219,0.188 10 true *a
*a Back-up Light Switch Assembly Connector


Connect the back-up light switch assembly connector.


Hide 28100 15.INSTALL STARTER ASSEMBLY

Hide 17.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

Hide 18. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART