When the manual transaxle assembly is removed, be sure to use a new clutch release with bearing cylinder assembly and new installation bolts. Removal of the manual transaxle assembly allows the compressed clutch release with bearing cylinder assembly to return to its original position. Dust from the moving section may damage the seal of the clutch release with bearing cylinder assembly, possibly causing clutch fluid leaks.
35150D
1.INSTALL TRANSMISSION CASE PLUG ASSEMBLY
2.INSTALL WIRE HARNESS CLAMP BRACKET
87121V
3.INSTALL HEATER BRACKET
31400
4.INSTALL CLUTCH RELEASE CYLINDER WITH BEARING ASSEMBLY
31407B
5.REMOVE CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
6.INSPECT CLUTCH PIPE LINE
31407B
7.INSTALL CLUTCH RELEASE BLEEDER SUB-ASSEMBLY
31484
8.INSTALL CLUTCH FLEXIBLE HOSE BRACKET
31483
9.INSTALL BLEEDER CLUTCH RELEASE TUBE
30300
10.SUPPORT MANUAL TRANSAXLE ASSEMBLY
| *a | Lashing Belt |
Using a transmission jack, support the manual transaxle assembly.
Adjust the attachment of the transmission jack to securely support the manual transaxle assembly.
Using a lashing belt or a rope, secure the manual transaxle assembly to the transmission jack.
30300
11.INSTALL MANUAL TRANSAXLE ASSEMBLY
12372A
12.INSTALL ENGINE MOUNTING INSULATOR LH
| *a | Temporarily Tighten |
Install the 4 bolts and nut in the order shown in the illustration.
Install the 4 bolts and nut in the order shown in the illustration.
Engage the clamp and connect the engine wire from the engine mounting insulator LH.
12321B
13.INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY
12364B
14.INSTALL NO. 2 ENGINE MOVING CONTROL ROD
| *a | Temporarily Tighten |
Install the No. 2 engine moving control rod to the manual transmission case with the 4 bolts in the order shown in the illustration.
51201
15.INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY
16.REMOVE ENGINE SUPPORT BRIDGE
Remove SST from the vehicle body.
Prevent SST from contacting the vehicle body or windshield glass.
Install the No. 3 radiator hose to the fan shroud with the 2 bolts.
Connect the inlet hose to the vehicle body with the clip.
17.REMOVE ENGINE HANGERS
18.INSTALL FRONT DRIVE SHAFT ASSEMBLY
28100
19.INSTALL STARTER ASSEMBLY
45260
20.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY
45259A
21.INSTALL COLUMN HOLE COVER SILENCER SHEET
31481A
22.INSTALL NO. 1 CLUTCH HOSE
82121
23.CONNECT ENGINE WIRE
Engage the 3 clamps.
Engage the 3 clamps.
Connect the neutral position switch connector.
Engage the 3 clamps.
Install the 3 bolts.
Connect the back-up light switch assembly connector.
Engage the clamp.
17410
24.INSTALL FRONT EXHAUST PIPE ASSEMBLY
33820B
25.CONNECT TRANSMISSION CONTROL CABLE ASSEMBLY
74404A
26.INSTALL BATTERY CLAMP SUB-ASSEMBLY
89661
27.INSTALL ECM
17701
28.INSTALL AIR CLEANER CASE SUB-ASSEMBLY
29.INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE
55701J
30.INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY
55735A
31.INSTALL WATER GUARD PLATE LH
55815E
32.INSTALL FRONT NO. 1 VENTILATOR SEAL
33.INSTALL WINDSHIELD WIPER MOTOR AND LINK
34.INSTALL FRONT WHEELS
35.CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
33820B
36.ADJUST TRANSMISSION CONTROL CABLE ASSEMBLY
37.ADD MANUAL TRANSAXLE OIL
38.BLEED CLUTCH LINE
Click hereDrivetrain>CLUTCH>CLUTCH SYSTEM>BLEEDING
39.INSPECT MANUAL TRANSAXLE OIL
40.INSPECT MANUAL TRANSAXLE OIL LEAK
41.INSPECT FOR EXHAUST GAS LEAK
51447D
42.INSTALL CENTER NO. 4 ENGINE UNDER COVER
53876A
43.CONNECT FRONT FENDER LINER LH
53875A
44.CONNECT FRONT FENDER LINER RH
51442C
45.INSTALL ENGINE UNDER COVER LH
51441C
46.INSTALL ENGINE UNDER COVER RH
51451A
47.INSTALL CENTER ENGINE UNDER COVER
48.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
49. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE
When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.
Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART