Home › Engine / Hybrid System › CRUISE CONTROL › DYNAMIC RADAR CRUISE CONTROL SYSTEM (for Gasoline Model) › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424996 DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model) J

CRUISE CONTROL  DYNAMIC RADAR CRUISE CONTROL SYSTEM(for Gasoline Model)  Distance Control Switch Circuit  


DESCRIPTION

The vehicle-to-vehicle distance control switch is used to set the distance for vehicle-to-vehicle distance control mode. The vehicle-to-vehicle distance control switch is installed in the steering pad switch assembly. The vehicle-to-vehicle distance set value can be changed by operating the vehicle-to-vehicle distance control switch while the dynamic radar cruise control system is controlling vehicle speed in vehicle-to-vehicle distance control mode.

WIRING DIAGRAM

C408323E03
1.469,0.76 2.573,1.531 1.104,0.771 10 false Vehicle-to-vehicle Distance Control Switch 0.865,2.646 3,2.854 2.135,0.208 10 false Steering Pad Switch Assembly 3.083,2.615 4.823,2.917 1.74,0.302 10 false Spiral Cable Sub-assembly 5.229,1.208 7.01,1.469 1.781,0.26 10 false Forward Recognition Camera 5.792,2.99 6.448,3.219 0.656,0.229 10 false A54 3.063,2.031 3.375,2.229 0.313,0.198 10 false z2 3.073,0.594 3.385,0.792 0.313,0.198 10 false z2 4.26,0.594 4.573,0.792 0.313,0.198 10 false H60 4.26,2.042 4.573,2.24 0.313,0.198 10 false H60 5.219,1.031 5.531,1.229 0.313,0.198 10 false V10 3.656,0.49 4.271,0.688 0.615,0.198 10 false DIST 2.594,0.49 3.208,0.688 0.615,0.198 10 false DIST 2.583,1.938 3.198,2.135 0.615,0.198 10 false ECC 3.656,1.938 4.271,2.135 0.615,0.198 10 false ECC 5.667,2.073 6.281,2.271 0.615,0.198 10 false ECCS 5.667,0.625 6.281,0.823 0.615,0.198 10 false LKSW 5.667,2.563 6.281,2.76 0.615,0.198 10 false E1 3.094,0.385 3.25,0.583 0.156,0.198 10 false 8 3.063,1.833 3.344,2.031 0.281,0.198 10 false 12 4.344,0.396 4.5,0.594 0.156,0.198 10 false 6 4.354,1.844 4.51,2.042 0.156,0.198 10 false 2 5.479,0.5 5.635,0.698 0.156,0.198 10 false 3 5.375,1.938 5.604,2.135 0.229,0.198 10 false 28 5.406,2.417 5.635,2.615 0.229,0.198 10 false 10 5.781,3.156 6.438,3.385 0.656,0.229 10 false ECM

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the ECM, refer to Service Bulletin.

·

The vehicle is equipped with a Supplemental Restraint System (SRS) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION

·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One Time Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential Recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT




PROCEDURE

1.READ VALUE USING GTS (VEHICLE-TO-VEHICLE DISTANCE CONTROL SWITCH)
a.

Read the Data List according to the display on the GTS.

Powertrain > Radar Cruise2 > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Vehicle-to-vehicle Distance Control Switch Vehicle-to-vehicle distance control switch signal ON or OFF ON: Vehicle-to-vehicle distance control switch pushed
OFF: Vehicle-to-vehicle distance control switch not pushed
-
Powertrain > Radar Cruise2 > Data List
Tester Display
Vehicle-to-vehicle Distance Control Switch
50003 426 4
OK:

The value of the Data List item changes according to the operation of the vehicle-to-vehicle distance control switch.



Result:
Proceed to
OK
NG



OK

NG

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA, ECM AND BODY GROUND)
a.

Disconnect the H60 spiral cable sub-assembly connector.


b.

Disconnect the V10 forward recognition camera connector.


c.

Disconnect the A54 ECM connector.


d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H60-6 (DIST) - V10-3 (LKSW) Always Below 1 Ω
H60-2 (ECC) - A54-28 (ECCS) Always Below 1 Ω
H60-6 (DIST) or V10-3 (LKSW) - Body ground Always 10 kΩ or higher
H60-2 (ECC) or A54-28 (ECCS) - Body ground Always 10 kΩ or higher



e.

Connect the A54 ECM connector.


f.

Connect the V10 forward recognition camera connector.


g.

Connect the H60 spiral cable sub-assembly connector.


Result:
Result Proceed to
OK A
NG B



A

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)

B

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-10 (E1) - Body ground Always Below 1 Ω



c.

Connect the A54 ECM connector.


Result:
Proceed to
OK
NG



OK

6.CHECK ECM (ECM TERMINALS)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK ECM (ECM TERMINALS)
a.

Disconnect the A54 ECM connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A54-28 (ECCS) - A54-10 (E1) Always Below 1 Ω



c.

Connect the A54 ECM connector.


Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG