Home › Engine / Hybrid System › CRUISE CONTROL › LANE TRACING ASSIST SYSTEM › 2020.03–2020.07
RM36W0E _51 Engine / Hybrid System _088664 CRUISE CONTROL _0424999 LANE TRACING ASSIST SYSTEM J

CRUISE CONTROL  LANE TRACING ASSIST SYSTEM  Steering Pad Switch Circuit  


DESCRIPTION

The forward recognition camera receives LTA main switch signals from the steering pad switch assembly.

WIRING DIAGRAM

for HV Model:
A406735E55
1.417,1.281 2.625,1.531 1.208,0.25 10 false LTA Main Switch 1.042,2.302 3.188,2.563 2.146,0.26 10 false Steering Pad Switch Assembly 3.156,1.635 4.104,2.083 0.948,0.448 10 false Spiral Cable Sub-assembly 4.906,1.031 6.896,1.219 1.99,0.188 10 false Forward Recognition Camera 4.042,0.5 4.5,0.698 0.458,0.198 10 false H60 4.042,1.104 4.5,1.302 0.458,0.198 10 false H60 2.906,0.5 3.365,0.698 0.458,0.198 10 false z2 2.906,1.115 3.365,1.313 0.458,0.198 10 false z2 3.427,0.406 4.042,0.604 0.615,0.198 10 false DIST 3.417,1.01 4.031,1.208 0.615,0.198 10 false ECC 4.906,0.844 5.292,1.063 0.385,0.219 10 false V10 5.375,0.521 5.875,0.719 0.5,0.198 10 false LKSW 5.198,0.406 5.51,0.604 0.313,0.198 10 false 3 4.115,0.302 4.427,0.5 0.313,0.198 10 false 6 4.125,0.906 4.438,1.104 0.313,0.198 10 false 2 2.896,0.906 3.208,1.104 0.313,0.198 10 false 12 2.938,0.302 3.25,0.5 0.313,0.198 10 false 8 2.323,0.344 2.719,0.531 0.396,0.188 10 false DIST 2.333,0.938 2.76,1.146 0.427,0.208 10 false ECC

for Gasoline Model:
A401977E44
1.438,1.271 2.594,1.542 1.156,0.271 10 false LTA Main Switch 1.052,2.292 3.094,2.521 2.042,0.229 10 false Steering Pad Switch Assembly 3.156,1.625 4.094,2.063 0.938,0.438 10 false Spiral Cable Sub-assembly 5,0.99 6.854,1.208 1.854,0.219 10 false Forward Recognition Camera 4.969,0.844 5.427,1.042 0.458,0.198 10 false V10 2.906,0.5 3.219,0.698 0.313,0.198 10 false z2 2.896,1.104 3.208,1.302 0.313,0.198 10 false z2 2.938,0.302 3.094,0.5 0.156,0.198 10 false 8 2.896,0.906 3.104,1.104 0.208,0.198 10 false 12 3.417,0.396 4.031,0.594 0.615,0.198 10 false DIST 3.427,1.01 3.885,1.208 0.458,0.198 10 false ECC 4.042,0.5 4.5,0.698 0.458,0.198 10 false H60 4.042,1.104 4.5,1.302 0.458,0.198 10 false H60 4.115,0.302 4.427,0.5 0.313,0.198 10 false 6 4.125,0.906 4.313,1.083 0.188,0.177 10 false 2 5.208,0.385 5.365,0.583 0.156,0.198 10 false 3 5.375,0.5 5.99,0.698 0.615,0.198 10 false LKSW 5.573,2.25 6.031,2.448 0.458,0.198 10 false A54 5.563,2.417 6.021,2.615 0.458,0.198 10 false ECM 5.385,1.771 6,1.969 0.615,0.198 10 false ECCS 5.125,1.656 5.583,1.854 0.458,0.198 10 false 28 2.385,0.938 2.781,1.146 0.396,0.208 10 false ECC 2.417,0.375 2.792,0.552 0.375,0.177 10 false DIST

CAUTION / NOTICE / HINT

NOTICE:
·

When replacing the forward recognition camera, always replace it with a new one. If a forward recognition camera which was installed to another vehicle is used, the information stored in the forward recognition camera will not match the information from the vehicle and a DTC may be stored.

·

When the forward recognition camera is replaced with a new one or the windshield glass is replaced or removed/installed, make sure to read Before Starting Adjustment, then perform optical axis alignment for the forward recognition camera and clear the vehicle control history for each system.

HINT:

Forward recognition camera axis alignment can be performed by using either One Time Recognition, Sequential Recognition or Driving Adjustment.

One time recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(ONE TIME RECOGNITION)

Sequential recognition: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>TARGET ADJUSTMENT(SEQUENTIAL RECOGNITION)

Driving Adjustment: Click hereEngine / Hybrid System>CRUISE CONTROL>FRONT CAMERA>DRIVING ADJUSTMENT


·

During the steering pad switch assembly check, check the precautions for the airbag system since the horn button assembly is removed during servicing. (installation/removal of parts, checks, replacement, etc.)

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>PRECAUTION



PROCEDURE

1.READ VALUE USING GTS (LDA CONTROL)
a.

Read the Data List according to the display on the GTS.

Chassis > Lane Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
LDA Control Whether lane tracing assist system control is permitted or not Prohibit or Permit Prohibit: Lane tracing assist system control not possible
Permit: Lane tracing assist system control possible
-
Chassis > Lane Control > Data List
Tester Display
LDA Control
50003 418 3

Result:
Result Proceed to
Data List value changes when LTA Main Switch is operated A
Data List value does not change when LTA Main Switch is operated B



A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

B

2.INSPECT STEERING PAD SWITCH ASSEMBLY
2.INSPECT STEERING PAD SWITCH ASSEMBLY

Click hereSteering>STEERING COLUMN>STEERING PAD SWITCH>INSPECTION

Result:
Proceed to
OK
NG



OK

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

3.INSPECT SPIRAL CABLE SUB-ASSEMBLY

OK

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

4.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - FORWARD RECOGNITION CAMERA)
a.

Disconnect the H60 spiral cable sub-assembly connector.


b.

Disconnect the V10 forward recognition camera connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H60-6 (DIST) - V10-3 (LKSW) Always Below 1 Ω
H60-6 (DIST) or V10-3 (LKSW) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK VEHICLE CONDITION

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK VEHICLE CONDITION
a.

Check vehicle condition.


Result:
Result Proceed to
for HV Model A
for Gasoline Model B



A

6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)

B

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - BODY GROUND)
a.

Disconnect the H60 spiral cable sub-assembly connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H60-2 (ECC) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - ECM)
a.

Disconnect the H60 spiral cable sub-assembly connector.


b.

Disconnect the A54 ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H60-2 (ECC) - A54-28 (ECCS) Always Below 1 Ω
H60-2 (ECC) or A54-28 (ECCS) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

REPLACE FORWARD RECOGNITION CAMERA

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR