Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL PUMP
RM36W0E _51 Engine / Hybrid System _088661 M15A-FXE FUEL _0427237 FUEL PUMP A

M15A-FXE FUEL  FUEL PUMP  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during fuel pump removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)
Replacement of fuel pump Inspection after repair
·

Poor idle, etc.

·

Engine start function, etc.


(Click here)

CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.


·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.



NOTICE:

After the ignition switch is turned off, the radio and display receiver assembly records various types of memory and settings. As a result, after turning the ignition switch off, make sure to wait at least 120 seconds before disconnecting the cable from the negative (-) auxiliary battery terminal.


HINT:

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

·

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system

·

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2. DISCHARGE FUEL SYSTEM PRESSURE

Hide 3.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 4.REMOVE REAR SEAT ASSEMBLY

Hide 58325E 5.REMOVE REAR FLOOR SERVICE HOLE COVER

a.

Using a clip remover with its tip wrapped with protective tape, remove the rear floor service hole cover and butyl tape.

A459671C01
1.219,0.76 0.885,1 true 0.646,0.927 0.854,1.094 0.208,0.167 10 true *a
*a Protective Tape - -



b.

Disconnect the 2 fuel suction tube with pump and gauge assembly connectors.


Hide 77027B 6.DISCONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.
A465968

Slide the clip and disconnect the No. 1 fuel emission tube sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77701W 7.DISCONNECT NO. 1 CANISTER OUTLET HOSE SUB-ASSEMBLY

a.
A465969

Slide the clip and disconnect the No. 1 canister outlet hose sub-assembly from the fuel suction tube with pump and gauge assembly.


Hide 77209F 8.DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

A465970C01
1.115,1.385 1.365,1.385 true 5,1.333 5.167,1.167 false 4.74,0.698 5.323,0.698 false 4.667,0.167 5,0.333 false 5.75,0.281 6,0.167 false 5.906,0.948 6.417,0.927 6.417,0.927 5.896,0.844 true 1.406,0.854 1.656,1.021 true 4.833,1.25 5.146,1.406 0.313,0.156 10 false *1 0.906,1.281 1.104,1.458 0.198,0.177 10 true *2 1.208,0.76 1.396,0.927 0.188,0.167 10 true *3 6.021,0.073 6.333,0.229 0.313,0.156 10 false *a 6.448,0.833 6.76,0.99 0.313,0.156 10 false *b 4.49,0.063 4.802,0.219 0.313,0.156 10 false *c 4.552,0.594 4.865,0.75 0.313,0.156 10 false *2
*1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
*3 Fuel Tank Main Tube Sub-assembly -
*a Fuel Tube Joint *b O-ring
*c Nylon Tube -
V100135

Pull off
V100136

Pull off


NOTICE:
·

Remove any foreign matter on the fuel tube joint before performing this work.

·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Be sure to disconnect the fuel tube joint by hand.

·

Do not bend, twist, pinch or kink the nylon tube.

·

Cover the disconnected fuel tube joint with a plastic bag to prevent damage and contamination.

·

If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.




Hide 77144 9.REMOVE FUEL PUMP GAUGE RETAINER

a.

Remove the fuel pump gauge retainer.

i.
A465971C01
0.958,2.885 1.385,2.76 true 0.802,0.792 1.167,0.792 true 0.604,0.375 0.969,0.375 true 2.344,0.917 2.729,0.719 true 2.563,1.188 2.896,1.271 true 2.25,1.396 2.552,1.542 true 1.385,2.656 1.573,2.823 0.188,0.167 10 true *a 0.385,0.26 0.583,0.438 0.198,0.177 10 true *b 0.604,0.677 0.781,0.854 0.177,0.177 10 true *c 2.75,0.615 2.938,0.792 0.188,0.177 10 true *d 2.906,1.177 3.104,1.354 0.198,0.177 10 true *b 2.573,1.448 2.75,1.635 0.177,0.188 10 true *c
*a Insertion Point
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)


Temporarily install SST (plate) and SST (claw) to the fuel pump gauge retainer.

SST
09808-01071  
09808-14031  (09808-01030, 09808-01090)

HINT:

Securely insert the ends of SST (claw) into the insertion points in the fuel pump gauge retainer.



ii.

While firmly pressing SST (claw) into the insertion points in the fuel pump gauge retainer, tighten SST (bolt).


iii.
A465972C01
1.042,1.156 1.344,1.156 false 1.396,1.521 1.688,1.521 true 2.667,2.75 2.844,2.75 true 1.729,1.802 2.021,1.802 true 1.75,2.323 2.094,2.146 true 0.906,1.052 1.073,1.26 0.167,0.208 10 true *a 2.042,1.708 2.219,1.896 0.177,0.188 10 true *b 1.729,1.417 1.948,1.635 0.219,0.219 10 true *e 2.865,2.646 3.031,2.844 0.167,0.198 10 true *c 2.125,2.031 2.333,2.208 0.208,0.177 10 true *d
*a SST (Handle)
*b SST (Plate)
*c SST (Claw)
*d SST (Bolt)
*e Extension Bar


Install SST (handle) and an extension bar to SST (plate).

SST
09808-01071  
09808-14031  (09808-01010, 09808-01030, 09808-01090)


iv.

Lightly press down on SST to prevent it from separating from the fuel pump gauge retainer. While pressing down on SST, rotate SST (handle) slowly to loosen the fuel pump gauge retainer.

NOTICE:
·

Do not use any tools other than specified as this may result in damage to the fuel pump gauge retainer or fuel tank assembly.

·

Do not press down on SST excessively as this may make the fuel pump gauge retainer hard to rotate, and may damage components.

·

Make sure to rotate SST (handle) horizontally. If it is rotated at an angle, SST may come off.

·

Do not spin SST too fast or use an impact wrench as this may result in damage to components.

·

If SST comes off of the fuel pump gauge retainer, loosen SST (bolt) and reinstall SST.




v.

While pressing down on the fuel suction tube with pump and gauge assembly, remove the fuel pump gauge retainer.



Hide 77020A 10.REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

a.
A465973

Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

NOTICE:

Be careful not to bend the arm of the fuel sender gauge assembly.



b.
A465974

Remove the fuel suction tube set gasket from the fuel tank assembly.