Home › Engine / Hybrid System › M15A-FXE (FUEL) › FUEL SYSTEM
RM36W0E _51 Engine / Hybrid System _088661 M15A-FXE FUEL _0427234 FUEL SYSTEM L

M15A-FXE FUEL  FUEL SYSTEM  PRECAUTION  


CAUTION:
·
A360563

Never perform work on fuel system components near any possible ignition sources.

·

Vaporized fuel could ignite, resulting in a serious accident.

·
A360564

Do not perform work on fuel system components without first disconnecting the cable from the negative (-) auxiliary battery terminal.

·

Sparks could cause vaporized fuel to ignite, resulting in a serious accident.

·
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.



BEFORE WORKING ON FUEL SYSTEM


a.

Before inspecting and repairing the fuel system, disconnect the cable from the negative (-) auxiliary battery terminal.

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY



b.

Do not smoke or work near fire when handling the fuel system.


c.

Keep fuel away from rubber or leather parts.



DISCHARGE FUEL SYSTEM PRESSURE


CAUTION:
·

Make sure the engine coolant temperature is 60°C (140°F) or less when performing this procedure.

·

Perform the following procedure to prevent fuel from spraying before removing any fuel system parts.

·

Pressure will still remain in the fuel lines even after performing the following procedure. When disconnecting a fuel line, cover it with a piece of cloth to prevent fuel from spraying or coming out.



a.

When discharging fuel system pressure by disconnecting the EFI MAIN NO. 2 relay:

i.

Remove the No. 1 engine room relay block cover.


ii.

Remove the EFI MAIN NO. 2 relay.


iii.

Connect the GTS to the DLC3.


iv.

Turn the ignition switch to ON (IG).


v.

Turn the GTS on.


vi.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

vii.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



viii.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean Bank 1) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>M15A-FXE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



ix.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank assembly.


x.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL


xi.

Install the EFI MAIN NO. 2 relay.


xii.

Install the No. 1 engine room relay block cover.



b.

When discharging fuel system pressure by disconnecting the fuel pump connector:

i.

Remove the rear seat cushion assembly.

Click hereVehicle Interior>SEAT>REAR SEAT ASSEMBLY>REMOVAL


ii.

Remove the rear floor service hole cover.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PUMP>REMOVAL


iii.
A456968

Disconnect the fuel suction tube with pump and gauge assembly connector.


iv.

Put the engine in Inspection Mode (Maintenance Mode).

Powertrain > Hybrid Control > Utility
Tester Display
Inspection Mode
50005 397 2103

v.

Start the engine. After the engine has stopped on its own, turn the ignition switch off.

NOTICE:

Do not increase the engine speed or drive the vehicle while waiting for the engine to stop on its own.



vi.

Crank the engine again and make sure that the engine does not start.

HINT:

DTC P008700 (Fuel Rail / System Pressure - Too Low) and P017100 (System Too Lean Bank 1) may be stored. Clear the DTCs before proceeding to the next step.

Click hereEngine / Hybrid System>M15A-FKS (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR



vii.

Remove the fuel tank cap assembly and discharge the pressure from the fuel tank sub-assembly.


viii.

Disconnect the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>MAINTENANCE>M15A-FXE AUXILIARY BATTERY>REMOVAL


ix.

Connect the fuel suction tube with pump and gauge assembly connector.


x.

Install the rear floor service hole cover.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL PUMP>INSTALLATION




FUEL LINE


a.

When disconnecting a high-pressure fuel line, a large amount of fuel will spray. Perform the following procedure:

i.

Discharge fuel system pressure.


ii.

Disconnect the fuel tube.


iii.

Drain the fuel remaining inside the fuel tube into a container.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



b.

Quick Type A:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A401631C04
0,0 0,0 false
V100135

Open
V100136

Pull


Clamp Type A (No. 1 Fuel Pipe Clamp):

Open the cover of the fuel pipe clamp and remove the fuel pipe clamp from the fuel tube connector.


ii.

Check that there is no dirt or other foreign matter around the fuel tube connector before disconnecting it. Clean the joint if necessary.


iii.
A314711C07
2.385,1.615 2.875,1.99 2.875,1.99 2.646,1.604 false 2.24,3.01 2.375,3.01 2.375,3.01 2.438,3.417 false 2.677,3.5 2.865,3.042 2.865,3.042 2.979,3.042 false 2.375,4.188 2.375,3.979 false 1.667,4.292 2.063,4.292 2.063,4.292 2.063,3.813 false 1.896,4.292 1.896,3.802 false 1,2.979 1.146,2.979 1.146,2.979 1.365,3.458 false 2.927,1.958 3.24,2.115 0.313,0.156 10 false *a 1.5,4.219 1.813,4.375 0.313,0.156 10 false *b 2.302,4.208 2.615,4.365 0.313,0.156 10 false *c 0.813,2.906 1.125,3.063 0.313,0.156 10 false *d 3.031,2.969 3.344,3.125 0.313,0.156 10 false *e 2.083,2.927 2.396,3.083 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Pinch
V100136

Pull


Pinch the retainer of the fuel tube connector, and then pull the fuel tube connector off of the fuel pipe.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



iv.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Be sure to disconnect the fuel tube connector by hand.

·

Do not allow any scratches or foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the fuel pipe.

·

Do not forcibly bend, twist or turn the nylon tube.




v.

Check if there is any foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


vi.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



c.

Quick Type A:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


i.
A284670C05
1.646,1.667 1.719,1.635 false
V100135

Push


Align the fuel tube connector with the fuel pipe, and push them together until the fuel tube connector makes a "click" sound. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean engine oil to the tip of the fuel pipe and reinsert it.


ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Engage the claw and install the No. 1 fuel pipe clamp.




d.

Quick Type B:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any dirt or foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A403898C01
1.833,2.344 2.073,2.031 2.073,2.031 2.219,2.031 false 2.271,1.948 2.583,2.104 0.313,0.156 10 false *a
*a Retainer
V100135

Retainer Holding Position
V100136

Pull out


While holding the retainer at the positions shown in the illustration, pull up the retainer to disengage the lock claws.

NOTICE:

Be sure to disconnect the fuel tube connector by hand.



ii.
A403899C01
1.167,0.354 1.313,0.354 1.313,0.354 1.625,0.646 false 1.896,1.948 2.104,1.573 2.104,1.573 2.25,1.573 false 1.979,3.188 2.073,2.938 2.073,2.938 2.219,2.938 false 1.354,3.333 1.604,3.333 1.604,3.333 1.604,3.594 false 2.125,3.885 2.281,4.302 2.281,4.302 2.396,4.302 false 0.833,4.177 0.833,3.917 true 1.875,4.26 1.875,4.063 false 1.479,3.594 1.479,3.333 false 1,0.26 1.313,0.417 0.313,0.156 10 false *a 1.198,3.24 1.51,3.396 0.313,0.156 10 false *b 1.802,4.292 2.115,4.448 0.313,0.156 10 false *c 0.75,4.208 1.063,4.365 0.313,0.156 10 false *d 2.448,4.208 2.76,4.365 0.313,0.156 10 false *e 2.302,1.49 2.615,1.646 0.313,0.156 10 false *a 2.271,2.854 2.583,3.01 0.313,0.156 10 false *a
*a Retainer
*b O-ring
*c Fuel Tube Connector
*d Nylon Tube
*e Fuel Pipe
V100135

Retainer Holding Position
V100136

Pull out
V100137

Pull off


Pull up the retainer while holding it at the positions shown in the illustration and pull off the fuel tube connector.


iii.

If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:
·

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

·

Do not bend, twist, pinch or kink the nylon tube.




iv.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


v.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



e.

Quick Type B:

Perform the following procedure when connecting a fuel tube connector.

NOTICE:

Check that there is no damage or foreign matter on the connecting parts of the fuel lines.


i.
A393281C01
1.167,2.354 1.448,2.354 false 1,2.25 1.313,2.406 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe, push the fuel tube connector onto the fuel pipe, then push in the retainer to secure the connection.

NOTICE:

Confirm that the retainer makes a "click" sound when pushed.


HINT:

If it is difficult to push the fuel tube connector onto the fuel pipe, apply a small amount of clean gasoline to the tip of the fuel pipe.



ii.

After connecting the fuel lines, check that the fuel pipe and fuel tube connector are securely connected by pulling on them.


iii.

Clamp Type A (No. 1 Fuel Pipe Clamp):

Install the EFI fuel pipe clamp to the fuel tube connector and close the cover of the EFI fuel pipe clamp.




f.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310728C05
0.854,3.063 1.073,3.063 1.073,3.063 1.26,2.854 false 2.052,2.75 2.417,2.75 false 0.688,2.979 1,3.135 0.313,0.156 10 false *a 1.885,2.667 2.198,2.823 0.313,0.156 10 false *a
*a Retainer
V100135

Pull out
V100136

Pull off


Pull out the retainer to disengage the lock claws and pull off the fuel tube connector.


ii.
A310289C05
1.979,1.729 1.979,1.302 false 1.656,1.74 2.135,1.74 2.135,1.74 2.135,1.313 false 2.875,1.729 2.875,1.531 2.875,1.531 2.583,1.25 false 2.542,0.917 2.708,0.49 2.708,0.49 2.802,0.49 false 2.052,0.427 2.219,0.427 2.219,0.427 2.375,0.844 false 0.958,0.563 1.125,0.563 1.125,0.563 1.281,0.979 false 2.792,1.75 3.104,1.906 0.313,0.156 10 false *a 2.865,0.417 3.177,0.573 0.313,0.156 10 false *b 0.771,0.49 1.083,0.646 0.313,0.156 10 false *c 1.865,0.354 2.094,0.51 0.229,0.156 10 false *d 1.469,1.667 1.781,1.823 0.313,0.156 10 false *e
*a Fuel Pipe
*b Retainer
*c Nylon Tube
*d Fuel Tube Connector
*e O-ring


If the fuel tube connector and fuel pipe are stuck, push and pull the fuel tube connector to release it. Pull the fuel tube connector off of the fuel pipe carefully.

NOTICE:

Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).



iii.

Check that there is no foreign matter on the sealing surfaces of the disconnected fuel lines. Clean them if necessary.


iv.

Cover the disconnected fuel pipe and fuel tube connector with plastic bags to prevent damage and contamination.



g.

Quick Type C:

Perform the following procedure when disconnecting a fuel tube connector.

NOTICE:

Remove any foreign matter on the fuel tube connector and fuel pipe before performing this work.


i.
A310729C05
0.844,3.094 1.031,3.094 1.031,3.094 1.271,2.844 false 2.021,2.75 2.406,2.75 false 0.677,3 0.99,3.156 0.313,0.156 10 false *a 1.844,2.656 2.156,2.813 0.313,0.156 10 false *a
*a Retainer
V100135

Push
V100136

Push in


Align the fuel tube connector with the fuel pipe and push them together. If it is difficult to push the fuel pipe into the fuel tube connector, apply a small amount of clean gasoline to the tip of the fuel pipe and reinsert it.


ii.

Connect the fuel lines and push in the retainer. Check that the fuel pipe and fuel tube connector are securely connected by pulling on them.





FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


NOTICE:
·
A456957C01
0.396,1.177 0.781,1.344 true 0.219,1.094 0.531,1.25 0.313,0.156 10 false *a
*a Tube


Do not disconnect the tube shown in the illustration when disassembling the fuel suction tube with pump and gauge assembly. Doing so will cause reassembly of the fuel suction tube with pump and gauge assembly to be impossible as the tube is pressed into the fuel suction plate sub-assembly.

·

When replacing the fuel filter, replace it together with the fuel suction plate sub-assembly.




INSPECT FOR FUEL LEAK


a.

Check that there are no fuel leaks from the fuel system after doing any maintenance or repairs.

Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>ON-VEHICLE INSPECTION