Home › Drivetrain › AXLE AND DIFFERENTIAL › FRONT AXLE HUB (for TMC Made) › 2020.07–2020.09
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0430757 FRONT AXLE HUB(for TMC Made) A

AXLE AND DIFFERENTIAL  FRONT AXLE HUB(for TMC Made)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the front axle hub sub-assembly removal/installation are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
for HV Model:
Auxiliary battery terminal is disconnected/reconnected
Memorize steering angle neutral point Parking assist monitor system (Click here)
Front wheel alignment adjustment for HV Model:
1.

Perform "Reset Memory"

2.

Perform calibration (linear solenoid valve offset learning, SM solenoid valve offset learning, brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero pointcalibration)


·

DTCs are stored

·

ABS warning light illuminates

·

Brake system warning light (yellow indicator)

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
for Gasoline Model:
Calibration
·

DTCs are stored

·

ABS warning light illuminates

·

Slip indicator light illuminates

·

VSC disabled or malfunctions


(Click here)
Suspension, tires, etc.
(The vehicle height changes because of suspension or tire replacement.)
·

Ultrasonic sensor detection angle

·

Ultrasonic sensor detection angle registration


Parking support brake system (Click here)
Rear television camera assembly optical axis (Back camera position setting) Parking assist monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH and LH sides.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE FRONT WHEEL

Hide 89543 5.SEPARATE FRONT SPEED SENSOR

a.
C432134

Remove the bolt and separate the front speed sensor and front flexible hose from the front shock absorber assembly.

NOTICE:

Be sure to separate the front speed sensor and front flexible hose from the front shock absorber assembly completely.



b.
C427815

Remove the bolt, disengage the clamp and separate the front speed sensor from the front shock absorber assembly and steering knuckle.

NOTICE:
·

Prevent foreign matter from contacting the sensor tip.

·

Be careful not to damage the front speed sensor.

·

Clean the speed sensor installation hole and the contact surfaces every time the speed sensor is removed.




Hide 45047 6.SEPARATE TIE ROD END SUB-ASSEMBLY

Hide 7.SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY

Hide 43512 8.REMOVE FRONT DISC

Hide 48069 9.SEPARATE FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY

Hide 43420 10.SEPARATE FRONT DRIVE SHAFT ASSEMBLY

a.
C428552C01
2.552,0.906 2.76,0.906 true 2.438,0.635 2.76,0.635 2.76,0.635 2.76,1.677 true 2.688,1.708 3,1.865 0.313,0.156 10 false *a
*a Matchmark


Put matchmarks on the front drive shaft assembly and the front axle hub sub-assembly.


b.
C428553

Using a plastic hammer, separate the front drive shaft assembly from the front axle assembly.

NOTICE:
·

Do not damage the front drive shaft outboard joint boot.

·

Do not push the front axle assembly towards the outside of the vehicle any further than necessary.



HINT:

If it is difficult to separate the front drive shaft assembly from the front axle assembly, tap the end of the front drive shaft assembly using a brass bar and a hammer.



Hide 11.REMOVE FRONT AXLE ASSEMBLY

a.
C428566

Remove the 2 bolts, 2 nuts and front axle assembly from the front shock absorber assembly.

NOTICE:

When removing the nuts, keep the bolts from rotating.



Hide 43502C 12.REMOVE FRONT AXLE HUB SUB-ASSEMBLY

a.
C428606

Secure the front axle assembly between aluminum plates in a vise.

NOTICE:

Do not overtighten the vise.



b.

Using a 12 mm hexagon socket wrench, remove the 3 bolts, front axle hub sub-assembly and front disc brake dust cover from the steering knuckle.

NOTICE:
·

Do not drop the front axle hub sub-assembly.

·

Be careful not to damage the speed sensor rotor or contact surfaces.

·

Do not allow foreign matter to contact the speed sensor rotor or contact surfaces.