Home › Drivetrain › AXLE AND DIFFERENTIAL › REAR AXLE HUB BOLT (for TMC Made) › 2020.07–2020.09
RM36W0E _52 Drivetrain _087260 AXLE AND DIFFERENTIAL _0430760 REAR AXLE HUB BOLT(for TMC Made) A

AXLE AND DIFFERENTIAL  REAR AXLE HUB BOLT(for TMC Made)  REPLACEMENT  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear axle hub bolt replacement are shown below.

Necessary Procedures After Parts Removed/Installed/Replaced (for HV Model)
Replacement Part or Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Auxiliary battery terminal is disconnected/reconnected Memorize steering angle neutral point Parking assist monitor system (Click here)

HINT:
for HV Model
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -




HINT:
·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION (for HV Model)

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISABLE BRAKE CONTROL (for HV Model)

Hide 3.REMOVE REAR WHEEL

Hide 42431D 4.REMOVE BRAKE DRUM

Hide 42312E 5.REMOVE REAR AXLE HUB BOLT

a.
C428560C01
1.198,0.573 1.604,1.208 true 1.542,0.75 1.5,0.344 1.5,0.344 1.792,0.531 true 0.906,0.479 1.198,0.635 0.292,0.156 10 true SST 1.26,0.229 1.469,0.417 0.208,0.188 10 true *a 1.75,1.844 1.958,2.031 0.208,0.188 10 true *c 2.594,0.479 2.802,0.667 0.208,0.188 10 true *b
*a Service Nut
*b Hold
*c Turn


Temporarily install 2 service nuts to the rear axle hub bolts as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


NOTICE:

Install the service nuts to prevent damage to the rear axle hub bolts.



b.

Using SST and a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly remove the rear axle hub bolt.

SST
09611-12010  

NOTICE:

Do not damage the threads of the rear axle hub bolts.



Hide 42312E 6.INSTALL REAR AXLE HUB BOLT

a.

Temporarily install a new rear axle hub bolt to the rear axle hub and bearing assembly.


b.
C428561C01
1.396,1.427 0.823,1.427 0.823,1.427 1.177,1.229 true 1.99,0.479 2.344,0.635 true 2.313,0.177 2.667,0.521 true 0.667,1.333 0.896,1.51 0.229,0.177 10 true *a 2.104,0.063 2.302,0.219 0.198,0.156 10 true *b 1.375,1.823 1.688,1.979 0.313,0.156 10 false *c 1.896,1.458 2.208,1.615 0.313,0.156 10 false *d 1.75,0.385 1.979,0.563 0.229,0.177 10 true *a
*a Service Nut
*b Washer
*c Hold
*d Turn


Install a washer and service nut to the rear axle hub bolt as shown in the illustration.

Recommended Service Nut:

Thread diameter: 12.0 mm (0.472 in.)

Thread pitch: 1.5 mm (0.0591 in.)


HINT:

Recommended washer thickness is 5 mm (0.197 in.) or more.



c.

Using a screwdriver or an equivalent tool to hold the rear axle hub and bearing assembly, install the rear axle hub bolt by tightening the service nut.

NOTICE:
·

Install the service nuts to prevent damage to the rear axle hub bolts.

·

Do not damage the threads of the rear axle hub bolts.




d.

Remove the 3 service nuts and washer from the 3 rear axle hub bolts.


Hide 42431D 7.INSTALL BRAKE DRUM

Hide 8.INSTALL REAR WHEEL

Hide 9.CONNECT CABLE TO NEGATIVE AUXILIARY BATTERY TERMINAL (for HV Model)

Hide 10. INITIALIZATION AFTER RECONNECTING BATTERY TERMINAL (for HV Model)

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE

HINT:

When disconnecting and reconnecting the battery, there is an automatic learning function that completes learning when the respective system is used.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>AUTOMATIC LEARNING CHART