When the outer mirror switch assembly is operated, the mirror retract/return signal is sent to the main body ECU (multiplex network body ECU) and then to power distribution box assembly via CXPI communication.
The power distribution box assembly retracts or returns the outer rear view mirror assemblies based on the signal.
for TMMF Made
for TMC Made
Inspect the fuses for circuits related to this system before performing the following procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Service Bulletin.*1
The power mirror control system uses the CXPI communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the power mirror control system after confirming that the communication system is functioning properly.
*1: w/ Smart Entry and Start System
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Outer Mirror Fold Switch | Retractable outer mirror switch signal | OFF or ON | OFF: Retractable outer mirror switch not in retract position
ON: Retractable outer mirror switch in retract position |
- |
| Tester Display |
|---|
| Outer Mirror Fold Switch |
On the GTS screen, ON or OFF is displayed accordingly.
| Proceed to | |
|---|---|
| for TMMF Made | A |
| for TMC Made | B |
| NG | C |
A
B
C
Check the malfunctioning parts.
| Result | Proceed to |
|---|---|
| Both outer rear view mirror assemblies are malfunctioning | A |
| Outer rear view mirror assembly LH is malfunctioning | B |
| Outer rear view mirror assembly RH is malfunctioning | C |
A
B
C
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Fold Signal | Retract mirror operation | OFF or ON | - |
| Mirror Return Signal | Retract mirror operation | OFF or ON | - |
| Tester Display |
|---|
| Mirror Fold Signal |
| Tester Display |
|---|
| Mirror Return Signal |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Retract Mirror Input Signal | Power retract mirror drive signal (Input) | Stop, Retract, Return | Stop: Outer rear view mirror assembly not move
Retract: Outer mirror switch in retract position Return: Outer mirror switch in return position |
- |
| Tester Display |
|---|
| Power Retract Mirror Input Signal |
The GTS display changes correctly according to the outer mirror switch assembly operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Disconnect the 4C power distribution box assembly connector.
Disconnect the L14 outer rear view mirror assembly LH connector.
Disconnect the K14 outer rear view mirror assembly RH connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L14-9 (MF) | Always | Below 1 Ω |
| 4C-10 - K14-9 (MF) | Always | Below 1 Ω |
| 4C-21 - L14-3 (MR) | Always | Below 1 Ω |
| 4C-21 - K14-3 (MR) | Always | Below 1 Ω |
| 4C-10 - Body Ground | Always | 10 kΩ or higher |
| 4C-21 - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L14-9 (MF) | Always | Below 1 Ω |
| 4C-21 - L14-3 (MR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMMF Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - K14-9 (MF) | Always | Below 1 Ω |
| 4C-21 - K14-3 (MR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Check the malfunctioning parts.
| Result | Proceed to |
|---|---|
| Both outer rear view mirror assemblies are malfunctioning | A |
| Outer rear view mirror assembly LH is malfunctioning | B |
| Outer rear view mirror assembly RH is malfunctioning | C |
A
B
C
Perform the Active Test according to the display on the GTS.
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Mirror Fold Signal | Retract mirror operation | OFF or ON | - |
| Mirror Return Signal | Retract mirror operation | OFF or ON | - |
| Tester Display |
|---|
| Mirror Fold Signal |
| Tester Display |
|---|
| Mirror Return Signal |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Power Retract Mirror Input Signal | Power retract mirror drive signal (Input) | Stop, Retract, Return | Stop: Outer rear view mirror assembly not move
Retract: Outer mirror switch in retract position Return: Outer mirror switch in return position |
- |
| Tester Display |
|---|
| Power Retract Mirror Input Signal |
The GTS display changes correctly according to the outer mirror switch assembly operation.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Disconnect the L8*1 or L10*2 outer rear view mirror assembly LH connector.
*1: w/ Mirror Heater
*2: w/o Mirror Heater
Disconnect the K8*1 or K10*2 outer rear view mirror assembly RH connector.
*1: w/ Mirror Heater
*2: w/o Mirror Heater
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L8-11 (MF) | Always | Below 1 Ω |
| 4C-10 - K8-11 (MF) | Always | Below 1 Ω |
| 4C-21 - L8-3 (MR) | Always | Below 1 Ω |
| 4C-21 - K8-3 (MR) | Always | Below 1 Ω |
| 4C-10 - Body Ground | Always | 10 kΩ or higher |
| 4C-21 - Body Ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L10-6 (MF) | Always | Below 1 Ω |
| 4C-10 - K10-6 (MF) | Always | Below 1 Ω |
| 4C-21 - L10-7 (MR) | Always | Below 1 Ω |
| 4C-21 - K10-7 (MR) | Always | Below 1 Ω |
| 4C-10 - Body Ground | Always | 10 kΩ or higher |
| 4C-21 - Body Ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L8-11 (MF) | Always | Below 1 Ω |
| 4C-21 - L8-3 (MR) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - L10-6 (MF) | Always | Below 1 Ω |
| 4C-21 - L10-7 (MR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
Click hereVehicle Exterior>MIRROR (EXT)>OUTER REAR VIEW MIRROR (for TMC Made)>INSPECTION
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the 4C power distribution box assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - K8-11 (MF) | Always | Below 1 Ω |
| 4C-21 - K8-3 (MR) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4C-10 - K10-6 (MF) | Always | Below 1 Ω |
| 4C-21 - K10-7 (MR) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
NG
OK
NG
Disconnect the H5 main body ECU (multiplex network body ECU).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L12-9 (MAT) - H5-26 (AMR) | Always | Below 1 Ω |
| L12-10 (MR) - H5-27 (RET) | Always | Below 1 Ω |
| L12-8 (E) - Body ground | Always | Below 1 Ω |
| L12-9 (MAT) or H5-26 (AMR) - Body ground | Always | 10 kΩ or higher |
| L12-10 (MR) or H5-27 (RET) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K12-9 (MAT) - H5-26 (AMR) | Always | Below 1 Ω |
| K12-10 (MR) - H5-27 (RET) | Always | Below 1 Ω |
| K12-8 (E) - Body ground | Always | Below 1 Ω |
| K12-9 (MAT) or H5-26 (AMR) - Body ground | Always | 10 kΩ or higher |
| K12-10 (MR) or H5-27 (RET) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG