Home › Engine / Hybrid System › 1KR-FE (FUEL) › FUEL INJECTOR › from 2020.07
RM36W0E _51 Engine / Hybrid System _090956 1KR-FE FUEL _0431074 FUEL INJECTOR G

1KR-FE FUEL  FUEL INJECTOR  INSPECTION  


PROCEDURE

Hide 23250 1.INSPECT FUEL INJECTOR ASSEMBLY

a.
A333794C01
0.219,0.146 0.531,0.302 0.313,0.156 10 false *a
*a Component without harness connected
(Fuel Injector Assembly)


Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
1 - 2 20°C (68°F) 11.6 to 12.4 Ω


If the result is not as specified, replace the fuel injector assembly.


b.

Inspect the fuel injector assembly injection.

CAUTION:

Keep the fuel injector assembly away from sparks during the test.


i.

Disconnect the fuel tube sub-assembly.

Click hereEngine / Hybrid System>1KR-FE (ENGINE MECHANICAL)>ENGINE ASSEMBLY>REMOVAL


ii.
A264971C19
0.5,1.656 0.729,1.885 0.729,1.885 0.833,1.885 false 0.854,0.906 1.146,0.615 1.146,0.615 1.26,0.615 false 1.99,1.292 2.292,1.594 2.292,1.594 2.417,1.594 false 2.646,0.698 2.948,0.396 2.948,0.396 3.063,0.396 false 0.875,1.802 1.156,2.042 0.281,0.24 10 false *a 1.333,0.521 1.656,0.781 0.323,0.26 10 false *b 2.479,1.51 2.802,1.76 0.323,0.25 10 false *c 3.135,0.292 3.354,0.542 0.219,0.25 10 false *d
*a SST (Hose)
*b SST (Hose Band)
*c SST (Fuel Tube Connector)
*d Fuel Pipe (Vehicle Side)


Connect SST (fuel tube connector) to SST (hose) with SST (hose band), and then connect them to the fuel pipe (vehicle side).

SST
09268-31015  (09268-41500, 09268-41700, 95336-08070)


iii.

Apply a light coat of gasoline to a new O-ring. Then install the O-ring onto the fuel injector assembly.


iv.
A426333C01
1.563,0.135 1,0.135 false 1.552,0.906 0.99,0.906 false 1.552,2.052 0.99,2.052 false 2.479,0.292 1.917,0.292 false 2.896,1.406 2.333,1.406 false 1.979,1.104 1.75,1.104 false 2.031,1.042 2.344,1.198 0.313,0.156 10 false *1 0.802,0.063 1.115,0.219 0.313,0.156 10 false *a 2.531,0.229 2.844,0.385 0.313,0.156 10 false *b 0.802,0.823 1.115,0.979 0.313,0.156 10 false *c 2.938,1.344 3.25,1.5 0.313,0.156 10 false *d 0.813,1.979 1.125,2.135 0.313,0.156 10 false *e
*1 O-ring
*a SST (Hose)
*b SST (Hose Band)
*c SST (Adapter)
*d SST (Clamp)
*e Vinyl Tube


Connect SST (adapter) and SST (hose) to the fuel injector assembly, and hold them with SST (clamp).

SST
09268-31015  (09268-41141, 09268-41410, 09268-41700, 95336-08070)


v.
A426334C01
1.625,1.24 2.25,1.792 2.25,1.792 2.583,1.792 true 1.469,1.479 2.021,1.979 2.021,1.979 2.354,1.979 true 2.656,1.708 2.969,1.865 0.313,0.156 10 false *a 2.396,1.917 2.708,2.073 0.313,0.156 10 false *b
*a Lock
*b SST (Tie Band)


Tie SST (clamp) and SST (adapter) together with SST (tie band) as shown in the illustration.

SST
09268-31015  (09268-41800)

NOTICE:
·

As SST (tie band) does not completely prevent SST (clamp) from becoming loose, do not subject the parts to any impacts while using them.

·

Before using SST (tie band), make sure that there is no wear, damage or cracks. If there are any abnormalities, replace SST.



HINT:

When removing SST (tie band), disengage the lock.



vi.

Check that SST (clamp) and SST (adapter) cannot be easily separated.


vii.

Install a vinyl tube onto the fuel injector assembly.

CAUTION:

Install a suitable vinyl tube onto the fuel injector assembly to prevent fuel from spraying.



viii.

Set the fuel injector assembly in a graduated cylinder.


ix.

Connect the GTS to the DLC3.


x.

Turn the ignition switch on (IG).

NOTICE:

Do not start the engine.



xi.

Turn the GTS on.


xii.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

Powertrain > Engine and ECT > Active Test
Tester Display
Control the Fuel Pump / Speed
50004 234 5

xiii.
A426335C01
2.125,0.49 2.125,0.958 false 2.063,0.979 2.375,1.135 0.313,0.156 10 false *a
*a SST (EFI Inspection Wire I)


Connect SST (EFI inspection wire I) to the fuel injector assembly and battery for 15 seconds, and measure the injection volume with the graduated cylinder. Test each fuel injector assembly 2 or 3 times.

SST
09842-30090  

Standard Injection Volume:
Battery Connection Condition Specified Condition
Positive (+) auxiliary battery terminal - Negative (-) auxiliary battery terminal Per 15 seconds 32 to 38 cc (2.0 to 2.3 cu.in.)


Difference between Each Fuel Injector Assembly:

6 cc (0.4 cu. in.) or less


NOTICE:
·

Make sure that SST (EFI inspection wire I) is securely connected.

·

Always switch the voltage on and off at the battery side, not the fuel injector assembly side.



If the result is not as specified, replace the fuel injector assembly.



c.

Check for fuel drop.

i.

In the condition above, disconnect SST (EFI inspection wire I) from the battery and check for fuel drop from the fuel injector assembly.

Standard Fuel Drop:

1 drop or less per 205 minutes


If the result is not as specified, replace the fuel injector assembly.


ii.

Turn the ignition switch off.


iii.

Disconnect the GTS from the DLC3.


iv.