Home › Engine / Hybrid System › 1KR-FE (ENGINE MECHANICAL) › ENGINE ASSEMBLY › from 2020.07
RM36W0E _51 Engine / Hybrid System _091035 1KR-FE ENGINE MECHANICAL _0431330 ENGINE ASSEMBLY A

1KR-FE ENGINE MECHANICAL  ENGINE ASSEMBLY  INSTALLATION  


CAUTION / NOTICE / HINT

CAUTION:

The engine assembly with transaxle is very heavy. Be sure to follow the procedure described in the repair manual, or the engine lifter may suddenly drop.


PROCEDURE

Hide 12372A 2.INSTALL ENGINE MOUNTING INSULATOR LH

HINT:

Only perform this procedure when replacement of the engine mounting insulator LH is necessary.


a.
A469952C01
0.552,0.604 1.156,0.802 0.604,0.198 10 true 1 (*a), 5 2.406,2 2.573,2.177 0.167,0.177 10 true 2 0.323,1.208 0.49,1.385 0.167,0.177 10 true 3 3.167,1.604 3.333,1.781 0.167,0.177 10 true 4 3.021,0.052 3.188,0.229 0.167,0.177 10 true 6
*a Temporarily Tighten


Temporarily install the engine mounting insulator LH to the vehicle.


b.

Install the 5. bolts and nut in the order shown in the illustration.

Torque:
42 N*m (428 kgf*cm, 31 ft.*lbf)


Hide 12305 3.INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH

HINT:

Only perform this procedure when replacement of the engine mounting insulator sub-assembly RH is necessary.


a.
A471256C01
0.094,1.677 0.708,1.885 0.615,0.208 10 true 1 (*a), 4 2.927,1.75 3.104,1.99 0.177,0.24 10 true 2 2.469,0.271 2.646,0.51 0.177,0.24 10 true 3
*a Temporarily Tighten


Temporarily install the engine mounting insulator sub-assembly RH to the vehicle.


b.

Install the 2 bolts and nut in the order shown in the illustration.

Torque:
72 N*m (734 kgf*cm, 53 ft.*lbf)


c.

Connect the air conditioner tube with the 2 clamps.


Hide 4.REMOVE ENGINE STAND

a.

Using a chain block and a sling device, secure the engine assembly.

NOTICE:

Make sure that the sling angle is correct to prevent the engine assembly and engine hangers from being damaged or deformed.



b.

Remove the engine stand from the engine assembly.


Hide 31250 6.INSTALL CLUTCH DISC ASSEMBLY

Hide 31210 7.INSTALL CLUTCH COVER ASSEMBLY

Hide 31210 8.INSPECT AND ADJUST CLUTCH COVER ASSEMBLY

Hide 28100 10.INSTALL STARTER ASSEMBLY (w/ Stop And Start System)

Hide 28100 11.INSTALL STARTER ASSEMBLY (w/o Stop And Start System)

Hide 11363A 12.INSTALL FLYWHEEL HOUSING SIDE COVER

Hide 82121 13.INSTALL ENGINE WIRE

a.

Connect all the wire harnesses and connectors.


b.

Connect the engine wire to the cylinder head cover sub-assembly with the bolt.

Torque:
8.4 N*m (86 kgf*cm, 74 in.*lbf)


c.

Connect the engine wire to the cylinder head sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


Hide 15.INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

a.

Using height adjustment attachments and plate lift attachments to keep the engine assembly with transaxle and front suspension crossmember sub-assembly level, set an engine lifter underneath the engine assembly with transaxle and front suspension crossmember sub-assembly.

NOTICE:
·

Using height adjustment attachments and plate lift attachments, keep the engine assembly with transaxle horizontal.

·

Do not perform any procedures while the engine assembly is suspended because doing so may cause the engine assembly to drop, resulting in injury. However, the engine assembly needs to be suspended when it is installed to or removed from an engine stand.

·

To prevent the oil pan sub-assembly from deforming, do not place any attachments under the oil pan sub-assembly of the engine assembly with transaxle.




b.

Operate the engine lifter and lift the engine assembly with transaxle to the position where the engine mounting insulator sub-assembly RH and engine mounting insulator LH can be installed.

CAUTION:

Do not raise the engine assembly with transaxle more than necessary. If the engine is raised excessively, the vehicle may also be lifted up.


NOTICE:
·

Make sure that the engine assembly with transaxle is clear of all wiring and hoses.

·

While raising the engine assembly with transaxle into the vehicle, do not allow it to contact the vehicle.




c.
C432279N01
0.552,1.302 0.708,1.5 0.156,0.198 10 true A 2.719,1.333 2.875,1.531 0.156,0.198 10 true A 0.656,1.604 0.813,1.802 0.156,0.198 10 true A 2.635,1.604 2.792,1.802 0.156,0.198 10 true A 0.552,1.958 0.708,2.156 0.156,0.198 10 true A 2.74,1.948 2.896,2.146 0.156,0.198 10 true A 2.198,0.385 2.354,0.583 0.156,0.198 10 true A 1.094,0.365 1.25,0.563 0.156,0.198 10 true A 0.333,0.094 0.49,0.292 0.156,0.198 10 true B 2.958,0.104 3.115,0.302 0.156,0.198 10 true B

Install the front suspension crossmember sub-assembly to the vehicle body with the 8 bolts (A).

Torque:
107.5 N*m (1096 kgf*cm, 79 ft.*lbf)


d.

Install the 2 bolts (B).

Torque:
30 N*m (306 kgf*cm, 22 ft.*lbf)


e.
A469950N01
2.958,1.708 3.115,1.906 0.156,0.198 10 true 1 0.844,0.229 1,0.427 0.156,0.198 10 true 2 0.865,1.365 1.021,1.563 0.156,0.198 10 true 3 0.448,0.729 0.604,0.927 0.156,0.198 10 true 4

Install the engine mounting insulator LH to the engine mounting bracket LH with the 3 bolts and nut in the order shown illustration.

Torque:
Bolt : 42 N*m (428 kgf*cm, 31 ft.*lbf)
Nut : 20 N*m (204 kgf*cm, 15 ft.*lbf)


f.
A471255C01
0.229,0.646 0.385,0.844 0.156,0.198 10 true 1 2.99,0.781 3.146,0.979 0.156,0.198 10 true 2 2.802,1.688 2.958,1.885 0.156,0.198 10 true 3

Install the engine mounting insulator sub-assembly RH to the engine mounting bracket RH with the 2 bolts and nut in the order shown illustration.

Torque:
Bolt : 72 N*m (734 kgf*cm, 53 ft.*lbf)
Nut : 41 N*m (418 kgf*cm, 30 ft.*lbf)


Hide 45260 16.CONNECT NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY

Hide 45259A 17.INSTALL COLUMN HOLE COVER SILENCER SHEET (for LHD)

Hide 45259A 18.INSTALL COLUMN HOLE COVER SILENCER SHEET (for RHD)

Hide 17410 24.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A171211E06
2.667,0.531 2.448,0.99 false 1.917,0.25 1.792,0.635 false 1.604,1.885 1.604,1.542 false 0.885,1.813 0.885,1.417 false 1.958,0.146 2.156,0.323 0.198,0.177 10 false *a 2.708,0.417 2.906,0.594 0.198,0.177 10 false *b 0.813,1.854 1.01,2.031 0.198,0.177 10 false *1 1.521,1.917 1.719,2.094 0.198,0.177 10 false *2

Using a plastic hammer and a wooden block, tap in a new No. 2 exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 No. 2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer

NOTICE:
·

Install the No. 2 exhaust pipe gasket in the correct direction.

·

Do not reuse the No. 2 exhaust pipe gasket.

·

Do not damage the No. 2 exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the No. 2 exhaust pipe gasket.

·

Do not push in the No. 2 exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.




b.
A171211E07
2.667,0.573 2.469,0.979 false 1.917,0.281 1.802,0.625 false 1.604,1.896 1.604,1.552 false 0.885,1.823 0.885,1.427 false 1.948,0.146 2.146,0.323 0.198,0.177 10 false *a 2.688,0.448 2.885,0.625 0.198,0.177 10 false *b 0.813,1.865 1.01,2.042 0.198,0.177 10 false *1 1.521,1.927 1.719,2.104 0.198,0.177 10 false *2

Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

Text in Illustration
*1 Exhaust Manifold
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.




c.
A128853

Using a vernier caliper, measure the free length of the compression spring.

Free Length of Compression Spring:
Compression Spring Standard Length Minimum Length
Front Side 43 mm (1.69 in.) 41.5 mm (1.63 in.)
Rear Side 40 mm (1.57 in.) 38.5 mm (1.52 in.)


If the length is not as specified, replace the compression spring.



d.

Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.


e.
A247549E06
0.354,0.458 0.552,0.615 false 1.927,0.948 2.073,1.385 true 0.521,0.896 0.323,1.063 false 0.146,0.365 0.458,0.583 0.313,0.219 10 false *1 0.125,1.01 0.438,1.229 0.313,0.219 10 false *2 2.042,1.385 2.354,1.604 0.313,0.219 10 false *3 2.729,1.344 3.042,1.563 0.313,0.219 10 false *a

Connect the front exhaust pipe sub-assembly to the exhaust manifold with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

After the installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



f.
A247551E02
0.466,0.624 0.621,0.767 0.155,0.143 10 *a 2.955,0.941 3.110,1.092 0.155,0.151 10 *1 2.955,1.321 3.110,1.472 0.155,0.151 10 *2 1.114,1.831 1.269,1.982 0.155,0.151 10 *3 2.651,1.11 2.955,1.068 false 2.645,1.338 2.94,1.399 false 1.46,1.365 1.288,1.819 false

Connect the front exhaust pipe assembly to the tail exhaust pipe assembly with the 2 compression springs and 2 bolts.

Text in Illustration
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 No. 2 Exhaust Pipe Gasket
*a Space between flanges: 6.5 mm (0.256 in.)

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

After the installation, check that the gaps between the flanges of the tail exhaust pipe assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



g.

Engage the 3 clamps to connect the No. 2 heated oxygen sensor connector wire to the fan shroud.


h.

Connect the No. 2 heated oxygen sensor connector.


Hide 57543C 25.INSTALL FRONT FLOOR CENTER BRACE

Hide 16572D 26.CONNECT NO. 2 RADIATOR HOSE

a.

Connect the No. 2 radiator hose to the water inlet and slide the hose clip to secure it.


Hide 16571C 27.CONNECT NO. 1 RADIATOR HOSE

a.

Connect the No. 1 radiator hose to the cylinder head sub-assembly and slide the hose clip to secure it.


Hide 87245 29.CONNECT INLET HEATER WATER HOSE

a.

Connect the inlet heater water hose to the heater unit and slide the hose clip to secure it.


Hide 87246 30.CONNECT OUTLET HEATER WATER HOSE

a.

Connect the outlet heater water hose to the heater unit and slide the hose clip to secure it.


Hide 23826 31.CONNECT NO. 1 FUEL VAPOR FEED HOSE

a.

Connect the No. 1 fuel vapor feed hose to the duty vacuum switching valve and slide the hose clip to secure it.


b.

Engage the clamp to connect the No. 1 fuel vapor feed hose to the hose clamp.


Hide 23901 32.CONNECT FUEL TUBE SUB-ASSEMBLY

NOTICE:

Check if there is any damage or foreign matter on the connecting parts of the fuel lines.


a.

Connect the fuel tube sub-assembly to the fuel tube.

Click hereEngine / Hybrid System>1KR-FE (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 23841B 33.INSTALL EFI FUEL PIPE CLAMP

a.

Install the EFI fuel pipe clamp to the fuel tube sub-assembly and fuel tube.


Hide 88310 34.INSTALL COMPRESSOR ASSEMBLY WITH PULLEY (w/ Air Conditioning System)

a.
A426038E01
2.51,1.063 2.677,1.24 0.167,0.177 10 true 2 0.969,1.844 1.135,2.021 0.167,0.177 10 true 3 0.448,0.531 0.74,0.719 0.292,0.188 10 true 1, 5 2.375,0.021 2.542,0.198 0.167,0.177 10 true 4

Temporarily install the compressor assembly with pulley to the cylinder block sub-assembly and oil pan sub-assembly.


b.

Fully tighten the 4 bolts in the sequence shown in the illustration.

Torque:
25 N*m (255 kgf*cm, 18 ft.*lbf)


c.

Connect the compressor assembly with pulley connector.


Hide 82121 36.CONNECT ENGINE WIRE

a.

Connect the engine wire to the positive (+) auxiliary battery terminal with the 2 nuts.

Torque:
7.6 N*m (77 kgf*cm, 67 in.*lbf)


b.

Connect the engine wire to the vehicle with the 2 bolts.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Disconnect the 3 connectors from the engine room relay block.


d.

Disengage the 2 claws to separate the engine wire from the engine room relay block.


Hide 82662A 37.INSTALL NO. 1 RELAY BLOCK COVER

a.

Install the No. 1 relay block cover to the engine room relay block.


Hide 74404A 38.INSTALL BATTERY CLAMP SUB-ASSEMBLY

a.

Install the battery clamp sub-assembly to the vehicle with the 3 bolts.

Torque:
15.4 N*m (157 kgf*cm, 11 ft.*lbf)


Hide 17701 39.INSTALL AIR CLEANER CASE SUB-ASSEMBLY

a.

Install the air cleaner case sub-assembly to the vehicle.


Hide 17801 40.INSTALL AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

a.

Install the air cleaner filter element sub-assembly to the air cleaner case sub-assembly.


Hide 17735 41.INSTALL AIR CLEANER ASSEMBLY WITH DUCT

Hide 43.INSTALL FRONT WHEEL

Hide 45.ADD ENGINE COOLANT

Hide 46.ADD MANUAL TRANSAXLE OIL

Hide 50.INSPECT FOR EXHAUST GAS LEAK

Hide 55701J 52.INSTALL OUTER COWL TOP PANEL (for LHD)

Hide 55701J 53.INSTALL OUTER COWL TOP PANEL (for RHD)

Hide 55815E 54.INSTALL FRONT NO. 1 VENTILATOR SEAL (for LHD)

Hide 55815E 55.INSTALL FRONT NO. 1 VENTILATOR SEAL (for RHD)

Hide 55734A 56.INSTALL WATER GUARD PLATE RH (for LHD)

Hide 55735A 57.INSTALL WATER GUARD PLATE LH (for RHD)

Hide 58.INSTALL WINDSHIELD WIPER MOTOR AND LINK

Hide 51441C 59.INSTALL ENGINE UNDER COVER RH

Hide 51442C 60.INSTALL ENGINE UNDER COVER LH

Hide 61.INSPECT AND ADJUST FRONT WHEEL ALIGNMENT