77277R
1.INSTALL FUEL TANK FILLER PIPE PROTECTOR (for TMMF Made)
Engage the 3 clamps to install a new fuel tank filler pipe protector to the fuel tank filler pipe sub-assembly.
Engage the 3 claws.
77277R
2.INSTALL FUEL TANK FILLER PIPE PROTECTOR (for TMC Made)
Engage the 4 clamps to install a new fuel tank filler pipe protector to the fuel tank filler pipe sub-assembly.
Engage the 4 claws.
77218A
3.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMMF Made)
Engage the 2 clamps to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.
77218A
4.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)
Engage the 3 clamps to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.
77216A
5.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMMF Made)
Engage the 2 clamps to install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.
77216A
6.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT (for TMC Made)
Engage the 3 clamps to install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.
77217A
7.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT
Engage the 2 claws to install the No. 2 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.
77027B
8.INSTALL NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Engage the clamp to install the No. 1 fuel emission tube sub-assembly to the fuel tank assembly.
77209F
9.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY
Engage the clamp to install the fuel tank main tube sub-assembly to the fuel tank assembly.
77100U
10.INSTALL FUEL TANK ASSEMBLY
The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.
Set the fuel tank assembly on an engine lifter.
Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.
Using the engine lifter, slowly raise the fuel tank assembly, and then temporarily install the fuel tank assembly with the 4 bolts.
Tighten the 4 bolts in the order shown in the illustration.
Be careful not to drop the fuel tank assembly.
When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.
Connect the fuel tank breather tube to the fuel tank filler pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
11.INSTALL FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMMF Made)
Engage the locations shown in the illustration, and engage the fuel tank filler pipe sub-assembly to the vehicle body.
Install the bolt.
Engage the 2 clamps.
12.INSTALL FUEL TANK FILLER PIPE SUB-ASSEMBLY (for TMC Made)
Engage the locations shown in the illustration, and engage the fuel tank filler pipe sub-assembly to the vehicle body.
Install the bolt.
77730C
13.CONNECT NO. 2 CHARCOAL CANISTER ASSEMBLY (for TMMF Made)
Connect the canister air tube from the No. 2 canister.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
Engage the clamp to install the No. 1 canister outlet hose sub-assembly to the fuel tank assembly.
58415Q
14.INSTALL NO. 1 REAR FLOOR BOARD (for TMMF Made)
77209F
15.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Connect the fuel tank main tube sub-assembly to the fuel pipe.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
77027B
16.CONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY
Connect the No. 1 fuel emission tube sub-assembly to the fuel pipe and slide the clip to secure it.
Click hereEngine / Hybrid System>M15A-FXE (FUEL)>FUEL SYSTEM>PRECAUTION
77606
17.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly with the 3 clips.
17410
18.INSTALL FRONT EXHAUST PIPE ASSEMBLY
51447D
19.INSTALL NO. 4 CENTER ENGINE UNDER COVER (for TMMF Made)
51447D
20.INSTALL NO. 4 CENTER ENGINE UNDER COVER (for TMC Made)
77310A
21.INSTALL FUEL TANK CAP ASSEMBLY
77020A
22.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
65638
23.INSTALL REAR WHEEL HOUSE LINER LH (for TMMF Made)
Install the rear fender liner with the grommet and 10 clips.
Install the 2 screws.
65638
24.INSTALL REAR WHEEL HOUSE LINER LH (for TMC Made)
Install the rear fender liner with the grommet and 5 clips.
Install the 2 screws.
52592
25.INSTALL REAR BUMPER SIDE SEAL LH (for TMMF Made)
26.INSTALL WHEEL ASSEMBLY
27.ADD FUEL