Home › Engine / Hybrid System › 1KR-FE (INTAKE / EXHAUST) › EXHAUST PIPE › from 2020.07
RM36W0E _51 Engine / Hybrid System _091036 1KR-FE INTAKE / EXHAUST _0431306 EXHAUST PIPE A

1KR-FE INTAKE / EXHAUST  EXHAUST PIPE  INSTALLATION  


PROCEDURE

Hide 17410 1.INSTALL FRONT EXHAUST PIPE ASSEMBLY

a.
A128853

Inspect the free length.

Free Length of Compression Spring:
Standard Length Minimum Length
43 mm (1.69 in.) 41.5 mm (1.63 in.)


i.

Using a vernier caliper, measure the free length of the compression spring.

If the length is not as specified, replace the compression spring.



b.
A171211C28
1.813,0.625 2.052,0.24 false 1,1.417 1,1.854 false 2.49,0.969 2.729,0.583 false 1.615,1.531 1.615,1.854 false 0.917,1.885 1.083,2.042 0.167,0.156 10 false *1 1.531,1.885 1.698,2.042 0.167,0.156 10 false *2 2.083,0.094 2.25,0.25 0.167,0.156 10 false *a 2.76,0.438 3,0.594 0.24,0.156 10 false *b
*1 Exhaust Manifold
*2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new exhaust pipe gasket until its surface is flush with the exhaust manifold.

NOTICE:
·

Install the exhaust pipe gasket in the correct direction.

·

Do not reuse the exhaust pipe gasket.

·

Do not damage the exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the exhaust pipe gasket.

·

Do not push in the exhaust pipe gasket with the front exhaust pipe assembly when connecting it.




c.

Connect the 3 exhaust pipe supports to install the front exhaust pipe assembly to the vehicle.


d.
A247549C29
0.271,0.521 0.542,0.667 false 0.281,0.958 0.531,0.896 false 1.958,0.979 2.125,1.229 true 0.115,0.438 0.281,0.656 0.167,0.219 10 false *1 0.115,0.896 0.281,1.104 0.167,0.208 10 false *2 2.063,1.24 2.219,1.438 0.156,0.198 10 false *3 2.75,1.344 2.958,1.594 0.208,0.25 10 false *a
*1 Exhaust Manifold
*2 Front Exhaust Pipe Assembly
*3 Exhaust Pipe Gasket
*a Space between flanges: 8.5 mm (0.335 in.)


Install the front exhaust pipe assembly to the exhaust manifold with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

After the installation, check that the gaps between the flanges of the exhaust manifold and front exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 17430 2.INSTALL TAIL EXHAUST PIPE ASSEMBLY

a.
A128853

Inspect the free length.

Free Length of Compression Spring:
Standard Length Minimum Length
40 mm (1.57 in.) 38.5 mm (1.52 in.)


i.

Using a vernier caliper, measure the free length of the compression spring.

If the length is not as specified, replace the compression spring.



b.
A171211C29
1.813,0.625 2.052,0.24 false 1,1.417 1,1.854 false 2.49,0.969 2.729,0.583 false 1.615,1.531 1.615,1.854 false 0.917,1.885 1.083,2.042 0.167,0.156 10 false *1 1.531,1.885 1.698,2.042 0.167,0.156 10 false *2 2.083,0.094 2.25,0.25 0.167,0.156 10 false *a 2.76,0.438 3,0.594 0.24,0.156 10 false *b
*1 Front Exhaust Pipe Assembly
*2 No. 2 Exhaust Pipe Gasket
*a Wooden Block
*b Plastic Hammer


Using a plastic hammer and a wooden block, tap in a new No. 2 exhaust pipe gasket until its surface is flush with the front exhaust pipe assembly.

NOTICE:
·

Install the No. 2 exhaust pipe gasket in the correct direction.

·

Do not reuse the No. 2 exhaust pipe gasket.

·

Do not damage the No. 2 exhaust pipe gasket by dropping it, etc.

·

Do not damage the outer surface of the No. 2 exhaust pipe gasket.

·

Do not push in the No. 2 exhaust pipe gasket with the tail exhaust pipe assembly when connecting it.




c.

Connect the 2 exhaust pipe supports to install the tail exhaust pipe assembly to the vehicle.


d.
A247551C19
0.466,0.624 0.621,0.767 0.155,0.143 10 *a 2.955,0.941 3.110,1.092 0.155,0.151 10 *1 2.955,1.321 3.110,1.472 0.155,0.151 10 *2 1.114,1.831 1.269,1.982 0.155,0.151 10 *3 2.651,1.11 2.955,1.068 false 2.645,1.338 2.94,1.399 false 1.46,1.365 1.288,1.819 false
*1 Front Exhaust Pipe Assembly
*2 Tail Exhaust Pipe Assembly
*3 No. 2 Exhaust Pipe Gasket
*a Space between flanges: 6.5 mm (0.256 in.)


Install the tail exhaust pipe assembly to the front exhaust pipe assembly with the 2 compression springs and 2 bolts.

Torque:
43 N*m (438 kgf*cm, 32 ft.*lbf)

NOTICE:

After the installation, check that the gaps between the flanges of the front exhaust pipe assembly and tail exhaust pipe assembly are consistent front-to-rear and left-to-right.



Hide 57543C 3.INSTALL CENTER NO. 1 FLOOR BRACE

a.

Install the center No. 1 floor brace to the vehicle with the 2 bolts.

Torque:
22 N*m (224 kgf*cm, 16 ft.*lbf)


Hide 5.INSPECT FOR EXHAUST GAS LEAK

If gas is leaking, tighten the areas necessary to stop the leak. Replace damaged parts as necessary.

HINT:

Perform "Inspection After Repairs" after repairing or replacing the exhaust system.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION