Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P055512  Brake Booster Pressure Sensor Circuit High Circuit Short to Battery  P055514  Brake Booster Pressure Sensor Circuit Low Circuit Short to Ground or Open  


DESCRIPTION

The ECM detects changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly installed to the brake booster assembly. If the ECM determines that there is a malfunction in the signal sent by the vacuum sensor assembly, it stores DTC P055512 or P055514.

A370625E01
0.188,0.156 3.552,0.354 3.365,0.198 10 false Vacuum Sensor Voltage: 0.948,0.51 1.813,0.771 0.865,0.26 10 false Voltage (V) 0.979,0.813 1.844,1.073 0.865,0.26 10 false 5.0 0.969,1.188 1.833,1.448 0.865,0.26 10 false 4.5 0.969,2.448 1.833,2.708 0.865,0.26 10 false 0.5 1.083,2.823 1.948,3.083 0.865,0.26 10 false 0 2.396,0.885 3.51,1.094 1.115,0.208 10 false Abnormal Range 2.385,2.594 3.5,2.802 1.115,0.208 10 false Abnormal Range 2.438,1.802 3.552,2.01 1.115,0.208 10 false Normal Range

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P055512 Brake Booster Pressure Sensor Circuit High Circuit Short to Battery The vacuum sensor assembly output voltage is 4.5 V or higher for 1.2 seconds or more (1 trip detection logic).
·

Open or Short in vacuum sensor assembly circuit

·

Vacuum sensor assembly

·

ECM


- DTC stored Engine A
P055514 Brake Booster Pressure Sensor Circuit Low Circuit Short to Ground or Open The vacuum sensor assembly output voltage is 0.5 V or less for 1.2 seconds or more (1 trip detection logic).
·

Open or Short in vacuum sensor assembly circuit

·

Vacuum sensor assembly

·

ECM


- DTC stored Engine A

MONITOR DESCRIPTION

If there is a defect or an open or short circuit in the vacuum sensor assembly, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the vacuum sensor assembly circuit and stores a DTC.

WIRING DIAGRAM

A382203E06
1.469,0.917 2,1.313 0.531,0.396 10 false VC 1.417,1.604 1.948,2 0.531,0.396 10 false PB 1.49,2.375 2.021,2.771 0.531,0.396 10 false E2 0.375,2.74 0.906,3.135 0.531,0.396 10 false A28 0.375,2.896 2.083,3.25 1.708,0.354 10 false Vacuum Sensor Assembly 1.771,0.802 2.302,1.198 0.531,0.396 10 false 3 1.771,1.479 2.302,1.875 0.531,0.396 10 false 2 1.771,2.281 2.302,2.677 0.531,0.396 10 false 1 4.385,0.802 4.917,1.198 0.531,0.396 10 false 56 4.375,1.49 4.906,1.885 0.531,0.396 10 false 54 4.385,2.271 4.917,2.667 0.531,0.396 10 false 55 4.646,2.99 5.177,3.385 0.531,0.396 10 false A55 4.635,3.146 5.115,3.427 0.479,0.281 10 false ECM 5.667,0.552 6.198,0.948 0.531,0.396 10 false 5 V 4.667,0.802 5.198,1.198 0.531,0.396 10 false BRVC 4.667,1.49 5.198,1.885 0.531,0.396 10 false PB 4.667,2.271 5.198,2.667 0.531,0.396 10 false BRE2

CONFIRMATION DRIVING PATTERN

DTC P055512 and P055514 are detected when the engine idles for 10 seconds or more.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK HARNESS AND CONNECTOR (VACUUM SENSOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the vacuum sensor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A28-3 (VC) - A55-56 (BRVC) Always Below 1 Ω
A28-2 (PB) - A55-54 (PB) Always Below 1 Ω
A28-1 (E2) - A55-55 (BRE2) Always Below 1 Ω
A28-3 (VC) or A55-56 (BRVC) - Body ground and other terminals Always 10 kΩ or higher
A28-2 (PB) or A55-54 (PB) - Body ground and other terminals Always 10 kΩ or higher
A28-1 (E2) or A55-55 (BRE2) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SENSOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF VACUUM SENSOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the vacuum sensor assembly connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A28-3 (VC) - A28-1 (E2) Ignition switch ON 4.75 to 5.25 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG