Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P05552A  Brake Booster Pressure Sensor Circuit Range/Performance Signal Stuck In Range  


DESCRIPTION

The ECM detects changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly installed to the brake booster assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P05552A Brake Booster Pressure Sensor Circuit Range/Performance Signal Stuck In Range The signal from the vacuum sensor assembly remains the same for 1.2 seconds or more even though the brake pedal has been operated or the vehicle is being driven (1 trip detection logic).
·

Vacuum sensor assembly

·

Brake booster assembly

·

Vacuum hose assembly (brake booster hose)

·

ECM


- DTC stored Engine B

MONITOR DESCRIPTION

If the brake pedal has been operated or the vehicle is being driven and the signal from the vacuum sensor assembly remains the same even though the brake booster assembly pressure should have changed, the ECM will determine that the vacuum sensor assembly is stuck and store DTC P05552A.

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P05552A is detected when accelerate the vehicle from rest to approximately 30 km/h (18.65 mph) or more and then decelerate the vehicle. (Repeating this pattern 30 times will cause the brake booster pressure to change.)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK ANY OTHER DTCS OUTPUT
a.

Check for other DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only P05552A is output A
P05552A and other DTCs are output B


HINT:

If any DTCs other than P05552A are output, troubleshoot those DTCs first.



A

2.INSPECT VACUUM HOSE ASSEMBLY (BRAKE BOOSTER HOSE)

B

GO TO DTC CHART

2.INSPECT VACUUM HOSE ASSEMBLY (BRAKE BOOSTER HOSE)
a.

Check the vacuum hose assembly (brake booster hose) for cracks or clogging (visual check).

HINT:

When the actual brake force is insufficient, check the brake booster assembly.


OK:

No cracks or clogging in the vacuum hose assembly (brake booster hose).



Result:
Proceed to
OK
NG



OK

3.REPLACE VACUUM SENSOR ASSEMBLY

NG

REPLACE VACUUM HOSE ASSEMBLY

3.REPLACE VACUUM SENSOR ASSEMBLY

NEXT

4.CLEAR DTC
4.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
5.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED

Pre-procedure1

a.

Turn the ignition switch to ON.


b.

Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
DTCs are not output A
P05552A is output B


Post-procedure1

d.

None.



A

END

B