Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P01201C  Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range  P02201C  Throttle/Pedal Position Sensor/Switch "B" Circuit Voltage Out of Range  


DESCRIPTION

HINT:

This ETCS (Electrical Throttle Control System) does not use a throttle cable.


The throttle position sensor is mounted on the throttle body with motor assembly, and detects the opening angle of the throttle valve.

The throttle body with motor assembly sensor has 2 sensor circuits which each transmits a signal, VTA1 and VTA2. VTA1 is used to detect the throttle valve angle and VTA2 is used to detect malfunctions in VTA1. The sensor signal voltages vary between 0 V and 5 V. The VTA1 sensor signal voltage varies in proportion to the throttle valve opening angle, and is transmitted to the VTA1 terminals of the ECM.

As the valve closes, the VTA1 sensor output voltage decreases, and as the valve opens, the VTA1 sensor output voltage increases. The ECM calculates the throttle valve opening angle according to these signals and controls the throttle actuator in response to driver inputs.

A313391E06
1.125,1.948 1.552,1.229 true 0.833,3.156 1.135,2.625 true 4.438,1.531 4.813,1.104 false 1.083,2.219 0.615,1.01 true 3.385,0.927 4.313,1.469 0.927,0.542 10 false Sensor Output Voltage 0.552,3.479 1.583,3.885 1.031,0.406 10 false Throttle Position Sensor 2.552,3.469 3.792,3.781 1.24,0.313 10 false ECM 0.76,3.198 1.5,3.365 0.74,0.167 10 false IC No. 2 1.604,1.156 2.313,1.333 0.708,0.177 10 false Magnet 1.833,1.76 2.229,2.073 0.396,0.313 10 false VC 1.698,2.083 2.219,2.344 0.521,0.26 10 false VTA1 1.688,2.76 2.25,3.052 0.563,0.292 10 false VTA2 1.76,2.427 2.208,2.677 0.448,0.25 10 false ETA 3.979,1.469 4.479,1.729 0.5,0.26 10 false 5.0 3.979,1.656 4.406,1.865 0.427,0.208 10 false 4.5 3.979,2.969 4.469,3.313 0.49,0.344 10 false 0.5 4.802,2.802 5.417,3.083 0.615,0.281 10 false VTA1 4.802,1.833 5.333,2.125 0.531,0.292 10 false VTA2 4.99,3.698 6.344,4.063 1.354,0.365 10 false Usable Range 4.188,3.781 4.625,4.156 0.438,0.375 10 false 0° 6.51,3.781 6.927,4.031 0.417,0.25 10 false 86° 4.385,3.271 4.875,3.604 0.49,0.333 10 false 5° 4.854,1.021 6.073,1.229 1.219,0.208 10 false Fail-safe Angle 0.063,0.906 0.771,1.083 0.708,0.177 10 false IC NO. 1

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P01201C Throttle / Pedal Position Sensor / Switch "A" Circuit Voltage Out of Range Both of the following conditions are met for 0.4 seconds (1 trip detection logic):
·

The difference between the sensor output of VTA1 and VTA2 is 6.3% or more.

·

The difference between the sensor output of VTA1 and assumed throttle angle with manifold absolute pressure sensor is 9% or more.


·

Throttle position sensor (throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored Engine A
P02201C Throttle/Pedal Position Sensor/Switch "B" Circuit Voltage Out of Range Both of the following conditions are met for 0.4 seconds (1 trip detection logic):
·

The difference between the sensor output of VTA1 and VTA2 is 6.3% or more.

·

The difference between the sensor output of VTA2 and assumed throttle angle with manifold absolute pressure sensor is 9% or more.


·

Throttle position sensor (throttle body with motor assembly)

·

Throttle position sensor circuit

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A322489E07
5.635,3.188 6.771,3.458 1.135,0.271 10 false ECM 0.344,3.167 2.708,3.573 2.365,0.406 10 false Throttle Position Sensor (Throttle Body with Motor Assembly) 0.354,3 0.74,3.208 0.385,0.208 10 false D18 5.292,3.188 5.688,3.417 0.396,0.229 10 false D50 1.917,1.917 2.167,2.135 0.25,0.219 10 false E2 1.74,2.5 2.146,2.719 0.406,0.219 10 false VTA2 1.813,1.333 2.219,1.552 0.406,0.219 10 false VTA 1.885,0.771 2.292,0.99 0.406,0.219 10 false VC 4.813,0.656 5.219,0.875 0.406,0.219 10 false VC 4.802,1.24 5.208,1.458 0.406,0.219 10 false VTA1 4.813,2.385 5.219,2.604 0.406,0.219 10 false VTA2 4.823,1.813 5.229,2.031 0.406,0.219 10 false ETA 2.188,0.656 2.354,0.875 0.167,0.219 10 false 2 2.188,1.24 2.354,1.458 0.167,0.219 10 false 1 2.188,2.375 2.354,2.594 0.167,0.219 10 false 3 2.188,1.833 2.354,2.052 0.167,0.219 10 false 4 4.49,0.656 4.781,0.896 0.292,0.24 10 false 116 4.49,1.24 4.781,1.479 0.292,0.24 10 false 117 4.573,2.385 5.031,2.708 0.458,0.323 10 false 83 4.479,1.802 4.938,2.115 0.458,0.313 10 false 115

CONFIRMATION DRIVING PATTERN

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


DTC P01201C and P02201C are detected when the vehicle is driven in the city at 30 to 50 km/h (19 to 31 mph) for 5 minutes.

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the ECM and/or throttle body with motor assembly, perform electronic throttle learning and idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION

·

If any DTCs related to the crankshaft position sensor, throttle position sensor and accelerator pedal sensor assembly are output simultaneously, inspect the VC circuit of each component.



HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (THROTTLE POSITION SENSOR VOLTAGE)
a.

Read the values displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Throttle Position Sensor No.1 Voltage
Throttle Position Sensor No.2 Voltage
50003 372 75,76
Result:
When Accelerator Pedal Fully Released When Accelerator Pedal Fully Depressed Trouble Area Proceed to
Throttle Position Sensor No.1 Voltage Throttle Position Sensor No.2 Voltage Throttle Position Sensor No.1 Voltage Throttle Position Sensor No.2 Voltage
4.8 to 4.98 V 0 to 0.2 V 4.8 to 4.98 V 0 to 0.2 V VC circuit open A
4.5 to 4.98 V 0 to 0.2 V 4.8 to 4.98 V 0 to 0.2 V ETA circuit open
0 to 0.2 V, or 4.8 to 4.98 V 3.9 to 4.4 V 0 to 0.2 V, or 4.8 to 4.98 V 3.9 to 4.3 V VTA1 circuit open or shorted to ground
0.6 to 1.1 V 0 to 0.2 V, or 4.8 to 4.98 V 0.7 to 1.1 V 0 to 0.2 V, or 4.8 to 4.98 V VTA2 circuit open or shorted to ground
0.6 to 1.1 V 3.9 to 4.4 V 4.2 to 4.54 V 0.46 to 0.76 V Throttle position sensor circuit normal B




A

2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

B

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P01201C OR P02201C)
2.CHECK HARNESS AND CONNECTOR (THROTTLE BODY WITH MOTOR ASSEMBLY - ECM)

Pre-procedure1

a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D18-2 (VC) - D50-116 (VC) Always Below 1 Ω
D18-1 (VTA) - D50-117 (VTA1) Always Below 1 Ω
D18-3 (VTA2) - D50-83 (VTA2) Always Below 1 Ω
D18-4 (E2) - D50-115 (ETA) Always Below 1 Ω
D18-2 (VC) or D50-116 (VC) - Body ground Always 10 kΩ or higher
D18-1 (VTA) or D50-117 (VTA1) - Body ground Always 10 kΩ or higher
D18-3 (VTA2) or D50-83 (VTA2) - Body ground Always 10 kΩ or higher
D18-4 (E2) or D50-115 (ETA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NEXT

4.PERFORM IDLE LEARNING
4.PERFORM IDLE LEARNING

NEXT

5.CLEAR DTC
5.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

6.CHECK WHETHER DTC OUTPUT RECURS (DTC P01201C OR P02201C)
6.CHECK WHETHER DTC OUTPUT RECURS (DTC P01201C OR P02201C)

Pre-procedure1

a.

Start the engine.


b.

Drive the vehicle at between 30 to 50 km/h (19 to 31 mph) for 5 minutes.


Procedure1

c.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output.



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

END

NG