Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P011011  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground  P011015  Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open  


DESCRIPTION

A283580E01
3.354,2.271 3.74,1.99 false 2.26,0.406 2.833,0.667 0.573,0.26 10 Fig. 1: 3.292,4.271 4.167,4.5 0.875,0.229 10 Temperature 2.396,0.969 2.771,1.219 0.375,0.25 10 (kΩ) 2.281,1.146 2.521,1.365 0.24,0.219 10 30 2.281,1.583 2.521,1.802 0.24,0.219 10 10 2.354,1.875 2.594,2.094 0.24,0.219 10 5 2.354,2.094 2.594,2.313 0.24,0.219 10 3 2.354,2.26 2.51,2.479 0.156,0.219 10 2 2.344,2.531 2.594,2.75 0.25,0.219 10 1 2.24,2.833 2.479,3.052 0.24,0.219 10 0.5 2.24,3.198 2.479,3.417 0.24,0.219 10 0.2 2.24,3.469 2.479,3.688 0.24,0.219 10 0.1 2.281,1.323 2.531,1.542 0.25,0.219 10 20 2.542,3.823 2.781,4.042 0.24,0.219 10 -20 2.938,3.823 3.177,4.042 0.24,0.219 10 0 3.208,3.823 3.448,4.042 0.24,0.219 10 20 3.521,3.823 3.76,4.042 0.24,0.219 10 40 3.833,3.823 4.073,4.042 0.24,0.219 10 60 4.146,3.823 4.385,4.042 0.24,0.219 10 80 4.385,3.823 4.625,4.042 0.24,0.219 10 100 2.583,4 2.823,4.219 0.24,0.219 10 -4 2.896,4 3.135,4.219 0.24,0.219 10 32 3.208,4 3.448,4.219 0.24,0.219 10 68 3.479,4 3.729,4.25 0.25,0.25 10 104 3.792,4 4.125,4.25 0.333,0.25 10 140 4.094,4 4.417,4.25 0.323,0.25 10 176 4.385,4 4.708,4.25 0.323,0.25 10 212 4.677,3.823 5,4.073 0.323,0.25 10 (°C) 4.677,4 5,4.25 0.323,0.25 10 (°F) 3.802,1.896 4.583,2.167 0.781,0.271 10 Acceptable 2.26,0.719 3.083,0.917 0.823,0.198 10 Resistance 2.24,3.021 2.479,3.24 0.24,0.219 10 0.3

The intake air temperature sensor is built into the manifold absolute pressure sensor, and monitors the intake air temperature. The intake air temperature sensor has a built-in thermistor that varies its resistance depending on the temperature of the intake air. When the air temperature is low, the resistance in the thermistor increases. When the temperature is high, the resistance drops. The variations in resistance are reflected in the voltage applied to the ECM terminal (See Fig 1).

The intake air temperature sensor is connected to the ECM. The 5 V power source voltage in the ECM is applied to the intake air temperature sensor from terminal THA via resistor R.

Resistor R and the intake air temperature sensor are connected in series. When the resistance value of the intake air temperature sensor changes in accordance with changes in the intake air temperature, the voltage at terminal THA also changes. Based on this signal, the ECM increases the fuel injection volume to improve the drivability during cold engine operation.

HINT:

When the intake air temperature sensor output is outside the normal range, the ECM determines this to be a malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P011011 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Ground Intake air temperature sensor output voltage is 0.05 V or less for 0.5 seconds (3 trip detection logic).
·

Open or short in intake air temperature sensor circuit

·

Short to power source circuit

·

Intake air temperature sensor (manifold absolute pressure sensor)

·

ECM


Comes on DTC stored Engine A
P011015 Intake Air Temperature Sensor 1 Bank 1 Circuit Short to Battery or Open Intake air temperature sensor output voltage is 4.95 V or more for 0.5 seconds (3 trip detection logic).
·

Short in intake air temperature sensor circuit

·

Intake air temperature sensor (manifold absolute pressure sensor)

·

ECM


Comes on DTC stored Engine A

HINT:

When any of these DTCs are output, check the intake air temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Intake Air Temperature.

Intake Air Temperature Malfunction
-40°C (-40°F) Open circuit
140°C (284°F) Short circuit


WIRING DIAGRAM

A415185E14
0.177,2.708 0.698,2.979 0.521,0.271 10 false D21 0.177,2.854 2.656,3.344 2.479,0.49 10 false Intake Air Temperature Sensor (Manifold Absolute Pressure Sensor) 5.667,3.104 6.073,3.333 0.406,0.229 10 false D50 6.01,3.104 6.417,3.333 0.406,0.229 10 false ECM 6.031,1.063 6.438,1.292 0.406,0.229 10 false 5 V 6,1.354 6.406,1.583 0.406,0.229 10 false R 5.417,1.448 5.823,1.677 0.406,0.229 10 false THA 5.406,2.073 5.813,2.302 0.406,0.229 10 false E21 5.052,1.458 5.458,1.688 0.406,0.229 10 false 128 5.052,2.063 5.458,2.292 0.406,0.229 10 false 127 1.99,1.448 2.396,1.677 0.406,0.229 10 false 4 1.99,2.052 2.396,2.281 0.406,0.229 10 false 2 1.604,1.448 2.01,1.677 0.406,0.229 10 false THA 1.688,2.042 2.094,2.271 0.406,0.229 10 false E2

CONFIRMATION DRIVING PATTERN

DTC P0112 and P0113 are detected when the engine idles for approximately 5 minutes.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ VALUE USING GTS (INTAKE AIR TEMPERATURE)
a.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
Result:
Result Proceed to
The value of Intake Air Temperature is -40°C A
The value of Intake Air Temperature is 140°C B


HINT:
·

If there is an open circuit, the GTS indicates -40°C (-40°F).

·

If there is a short circuit, the GTS indicates 140°C (284°F).





A

2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

B

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)
2.READ VALUE USING GTS (CHECK FOR OPEN IN WIRE HARNESS)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.

A429626C02
4.01,1.427 4.344,1.667 0.333,0.24 5.26,2.156 5.156,1.688 true 5.854,2.125 5.625,1.688 true 1.021,0.75 1.333,0.948 0.313,0.198 10 false *1 3.01,0.688 3.323,0.885 0.313,0.198 10 false *2 1.385,1.208 1.719,1.427 0.333,0.219 10 false THA 1.479,1.51 1.813,1.729 0.333,0.219 10 false E2 2.74,1.208 3.073,1.427 0.333,0.219 10 false THA 2.75,1.521 3.177,1.74 0.427,0.219 10 false E21 4.073,1.479 4.5,1.698 0.427,0.219 10 false D21 5.208,2.177 5.542,2.396 0.333,0.219 10 false E2 4.219,0.771 4.531,0.969 0.313,0.198 10 false *a 5.771,2.146 6.365,2.365 0.594,0.219 10 false THA
*1 Manifold Absolute Pressure Sensor *2 ECM
*a Front view of wire harness connector
(to Manifold Absolute Pressure Sensor)
- -



b.

Connect terminals 4 (THA) and 2 (E2) of the manifold absolute pressure sensor connector on the wire harness side.


Procedure1

c.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
Result:
Result Proceed to
The value of Intake Air Temperature is 140°C A
None of the above conditions are met B


HINT:

140°C = 284°F



Post-procedure1

d.

None.



A

B

3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
3.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D21-4 (THA) - D50-128 (THA) Always Below 1 Ω
D21-2 (E2) - D50-127 (E21) Always Below 1 Ω



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (CHECK FOR SHORT IN WIRE HARNESS)

Pre-procedure1

a.
A255925C89
0.667,0.156 0.823,0.313 0.156,0.156 10 false *1 2.573,0.156 2.729,0.313 0.156,0.156 10 false *2 2.229,0.802 2.531,0.958 0.302,0.156 10 false THA 2.229,1.188 2.656,1.344 0.427,0.156 10 false E21 0.958,0.833 1.26,0.99 0.302,0.156 10 false THA 1.031,1.177 1.458,1.333 0.427,0.156 10 false E2
*1 Manifold Absolute Pressure Sensor
*2 ECM


Disconnect the manifold absolute pressure sensor connector.


Procedure1

b.

Read the value displayed on the GTS.

Powertrain > Engine > Data List
Tester Display
Intake Air Temperature
50003 372 214
Result:
Result Proceed to
The value of Intake Air Temperature is -40°C A
None of the above conditions are met B


HINT:

-40°C = -40°F



Post-procedure1

c.

None.



A

B

5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)
5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM)

Pre-procedure1

a.

Disconnect the manifold absolute pressure sensor connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D21-4 (THA) or D50-128 (THA) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR