A thermistor is built into the engine coolant temperature sensor and changes its resistance value according to the engine coolant temperature. The structure of the sensor and connection to the ECM are the same as that of the intake air temperature sensor.
When the engine coolant temperature sensor output is outside the normal range, the ECM interprets this as a malfunction.
If DTC P011511 or P011515 is detected, the ECM performs engine control using an estimated engine coolant temperature calculated from the intake air temperature at the time of engine start and the intake air volume.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | MIL | Memory | DTC Output from | Priority |
|---|---|---|---|---|---|---|---|
| P011511 | Engine Coolant Temperature Sensor 1 Circuit Short to Ground | Engine coolant temperature sensor output voltage is 0.05 V or less for 0.5 seconds (3 trip detection logic). | ·
Open or short in engine coolant temperature sensor circuit ·
Short to power source circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored | Engine | A |
| P011515 | Engine Coolant Temperature Sensor 1 Circuit Short to Battery or Open | Engine coolant temperature sensor output voltage is 4.95 V or more for 0.5 seconds (3 trip detection logic). | ·
Short in engine coolant temperature sensor circuit ·
Engine coolant temperature sensor ·
ECM |
Comes on | DTC stored | Engine | A |
When any of these DTCs are output, check the engine coolant temperature using the GTS. Enter the following menus: Powertrain / Engine / Data List / All Data / Coolant Temperature.
| Engine Coolant Temperature | Malfunction |
|---|---|
| -40°C (-40°F) | Open circuit |
| 140°C (284°F) | Short circuit |
DTC P011511 and P011515 are detected when the engine idles for approximately 10 minutes.
After replacing the ECM, perform idle learning.
Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
Pre-procedure1
None.
Procedure1
Read the value displayed on the GTS.
| Tester Display |
|---|
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The value of Coolant Temperature is -40°C | A |
| The value of Coolant Temperature is 140°C | B |
If there is an open circuit, the GTS indicates -40°C (-40°F).
If there is a short circuit, the GTS indicates 140°C (284°F).
Post-procedure1
None.
A
B
Pre-procedure1
Disconnect the engine coolant temperature sensor connector.
| *1 | Engine Coolant Temperature Sensor | *2 | ECM |
| *a | Front view of wire harness connector
(to Engine Coolant Temperature Sensor) |
- | - |
Connect terminals 1 (E2) and 2 (THW) of the engine coolant temperature sensor connector on the wire harness side.
Procedure1
Read the value displayed on the GTS.
| Tester Display |
|---|
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The value of Coolant Temperature is 140°C | A |
| None of the above conditions are met | B |
140°C = 284°F
Post-procedure1
None.
A
B
Pre-procedure1
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D36-2 (THW) - D50-120 (THW) | Always | Below 1 Ω |
| D36-1 (E2) - D50-121 (ETHW) | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG
Pre-procedure1
| *1 | Engine Coolant Temperature Sensor |
| *2 | ECM |
Disconnect the engine coolant temperature sensor connector.
Procedure1
Read the value displayed on the GTS.
| Tester Display |
|---|
| Coolant Temperature |
| Result | Proceed to |
|---|---|
| The value of Coolant Temperature is -40°C | A |
| None of the above conditions are met | B |
-40°C = -40°F
Post-procedure1
None.
A
B
Pre-procedure1
Disconnect the engine coolant temperature sensor connector.
Disconnect the ECM connector.
Procedure1
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| D36-2 (THW) or D50-120 (THW) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
Post-procedure1
None.
OK
NG