Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P044311  EVAP System Purge Control Valve "A" Circuit Circuit Short to Ground  P044312  EVAP System Purge Control Valve "A" Circuit Circuit Short to Battery  P044313  Evaporative Emission System Purge Control Valve "A" Circuit Open  


DESCRIPTION

In order to reduce hydrocarbon (HC) emissions, evaporated fuel from the fuel tank is routed through the charcoal canister to the intake manifold for combustion in the cylinders. The ECM changes the duty signal to the purge VSV so that the intake of HC emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P044311 EVAP System Purge Control Valve "A" Circuit Circuit Short to Ground Short between EVP1 and ground circuit (3 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored Engine A
P044312 EVAP System Purge Control Valve "A" Circuit Circuit Short to Battery Short between EVP1 circuit and power source circuit (3 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored Engine A
P044313 Evaporative Emission System Purge Control Valve "A" Circuit Open Open or short in purge VSV circuit (3 trip detection logic).
·

Open or short in purge VSV circuit

·

Purge VSV

·

ECM


Comes on DTC stored Engine A

WIRING DIAGRAM

A458583E01
0.573,3.938 1.125,4.135 0.552,0.198 10 false Battery 0.406,2.823 1.531,3.01 1.125,0.188 10 false BATT-MAIN NO.1 6.177,2.875 6.552,3.083 0.375,0.208 10 false ECM 5.427,1.156 5.698,1.323 0.271,0.167 10 false D50 5.427,2.292 5.719,2.448 0.292,0.156 10 false A55 5.469,0.938 5.667,1.094 0.198,0.156 10 false 55 5.51,2.104 5.646,2.26 0.135,0.156 10 false 9 5.792,1.042 6.167,1.229 0.375,0.188 10 false EVP1 5.771,2.292 6.24,2.5 0.469,0.208 10 false MREL 0.49,1.313 1.125,1.677 0.635,0.365 10 false EFI-MAIN NO.1 1.813,1.938 2.823,2.156 1.01,0.219 10 false EFI-MAIN NO.1 4.323,1.552 6.229,1.844 1.906,0.292 10 false Purge VSV 3.979,1.552 4.302,1.74 0.323,0.188 10 false D26 3.896,1.063 4.021,1.25 0.125,0.188 10 false 1 4.979,1.052 5.104,1.24 0.125,0.188 10 false 2 4.531,1.01 5.146,1.208 0.615,0.198 10 false EVP1 4.063,1.01 4.375,1.208 0.313,0.198 10 false +B 3.031,1.292 4.26,1.49 1.229,0.198 10 false EFI NO.3 1.688,1.031 1.844,1.229 0.156,0.198 10 false 3 2.583,1.031 2.74,1.229 0.156,0.198 10 false 5 1.677,1.563 1.833,1.76 0.156,0.198 10 false 2 2.594,1.563 2.75,1.76 0.156,0.198 10 false 1

CONFIRMATION DRIVING PATTERN

DTC P0443 is detected when the engine is warmed up, stops, restarts after 30 seconds, and idles for 1 minute.

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM, perform idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (ACTIVATE THE VSV FOR EVAP CONTROL)
A200511C07
0.792,0.219 1.021,0.448 0.229,0.229 10 false *a 2.604,0.219 2.813,0.448 0.208,0.229 10 false *b
*a VSV is on
*b VSV is off


Pre-procedure1

a.

Disconnect the fuel vapor feed hose (charcoal canister side) of the purge VSV.


b.

Start the engine.


Procedure1

c.

When the purge VSV is operated using the GTS, check whether the port of the purge VSV applies suction your finger.

Powertrain > Engine > Active Test
Active Test Display
Activate the EVAP Purge VSV
Data List Display
EVAP (Purge) VSV
50004 372 1 226
OK:
GTS Operation Specified Condition
ON Purge VSV port applies suction to finger
OFF Purge VSV port applies no suction to finger



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

2.INSPECT PURGE VSV
2.INSPECT PURGE VSV

OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

NG

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF PURGE VSV)

Pre-procedure1

a.

Disconnect the purge VSV connector.


b.

Turn the ignition switch to ON.


Procedure1

c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
D26-1 (+B) - Body ground Ignition switch ON 11 to 14 V



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

4.CHECK HARNESS AND CONNECTOR (ECM - PURGE VSV)

NG

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - PURGE VSV)
4.CHECK HARNESS AND CONNECTOR (ECM - PURGE VSV)

Pre-procedure1

a.

Disconnect the ECM connector.


b.

Disconnect the purge VSV connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-55 (EVP1) - D26-2 (EVP1) Always Below 1 Ω
D50-55 (EVP1) or D26-2 (EVP1) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (EFI-MAIN NO. 1 RELAY - PURGE VSV)

Pre-procedure1

a.

Remove the EFI-MAIN NO. 1 relay from the No. 1 engine room relay block and junction block assembly.


b.

Disconnect the purge VSV connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
5 (EFI-MAIN NO. 1) - D26-1 (+B) Always Below 1 Ω
5 (EFI-MAIN NO. 1) or D26-1 (+B) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR