Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P060E87  Internal Control Module Throttle Position Performance Missing Message  P210018  Throttle Actuator "A" Control Motor Circuit Current Below Threshold  P210019  Throttle Actuator "A" Control Motor Circuit Current Above Threshold  P210064  Throttle Actuator "A" Control Motor Signal Plausibility Failure  P211819  Throttle Actuator "A" Control Motor Current Range/Performance Circuit Current Above Threshold  P211977  Throttle Actuator "A" Control Throttle Body Range/Performance Commanded Position Not Reachable  


DESCRIPTION

The throttle actuator is operated by the ECM, and opens and closes the throttle valve using gears. The opening angle of the throttle valve is detected by the throttle position sensor, which is mounted on the throttle body with motor assembly. The throttle position sensor provides feedback to the ECM in order that it can control the throttle actuator, and therefore the throttle valve, appropriately in response to driver inputs.

HINT:

This ETCS (Electronic Throttle Control System) does not use a throttle cable.


DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P060E87 Internal Control Module Throttle Position Performance Missing Message The driving IC detects a malfunction inside itself during operation (1 trip detection logic). ECM Comes on DTC stored Engine A
P210018 Throttle Actuator "A" Control Motor Circuit Current Below Threshold The driving IC detects an open in the throttle control motor circuit during operation (1 trip detection logic).
·

Open in throttle control motor circuit

·

Throttle body with motor assembly


Comes on DTC stored Engine A
P210019 Throttle Actuator "A" Control Motor Circuit Current Above Threshold The driving IC detects a short in the throttle control motor circuit during operation (1 trip detection logic).
·

Short in throttle control motor circuit

·

Throttle body with motor assembly


Comes on DTC stored Engine A
P210064 Throttle Actuator "A" Control Motor Signal Plausibility Failure When the absolute values for difference between the target throttle angle and actual throttle angle is more than threshold for 0.5 seconds or more (1 trip detection logic).
·

Open or short in throttle control motor circuit

·

Throttle body with motor assembly


Comes on DTC stored Engine A
P211819 Throttle Actuator "A" Control Motor Current Range/Performance Circuit Current Above Threshold The driving IC detects a high-current malfunction causing overheat in the throttle control motor circuit during operation (1 trip detection logic). Throttle body with motor assembly Comes on DTC stored Engine A
P211977 Throttle Actuator "A" Control Throttle Body Range/Performance Commanded Position Not Reachable The motor drive duty ratio for opening or closing the throttle valve is 80% or more for 5 seconds or more (1 trip detection logic).
·

Open or short in throttle control motor circuit

·

Throttle body with motor assembly


Comes on DTC stored Engine A

HINT:

The monitor always runs while the ignition switch is ON or the engine is running.


WIRING DIAGRAM

A327849E05
2.146,0.688 2.302,0.885 0.156,0.198 10 false 6 2.156,1.448 2.313,1.646 0.156,0.198 10 false 5 1.823,0.792 2.063,1 0.24,0.208 10 false M+ 1.844,1.583 2.083,1.792 0.24,0.208 10 false M- 0.521,2.031 0.844,2.24 0.323,0.208 10 false D18 0.823,2.031 2.333,2.479 1.51,0.448 10 false Throttle Body with Motor Assembly 5.198,0.917 6.25,1.427 1.052,0.51 10 false Throttle Actuator Control Circuit 5.552,2.302 5.917,2.531 0.365,0.229 10 false ECM 5.177,2.313 5.542,2.542 0.365,0.229 10 false D50 4.365,0.677 4.896,0.99 0.531,0.313 10 false 103 4.354,1.448 4.854,1.698 0.5,0.25 10 false 135 4.688,0.677 4.938,0.885 0.25,0.208 10 false M+ 4.677,1.448 4.917,1.656 0.24,0.208 10 false M-

CAUTION / NOTICE / HINT

NOTICE:

After replacing the ECM and/or throttle body with motor assembly, perform electronic throttle learning and idle learning.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>INITIALIZATION


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK FOR DTC
a.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372

Result:
Result Proceed to
Only P210064 or P211977 is output A
Only P060E87 and P210064 are output B
Only P060E87 and P211977 are output C
None of the above conditions are met D



A

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

B

C

D

2.CHECK HARNESS AND CONNECTOR (ECM - THROTTLE BODY WITH MOTOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (ECM - THROTTLE BODY WITH MOTOR ASSEMBLY)

Pre-procedure1

a.

Disconnect the throttle body with motor assembly connector.


b.

Disconnect the ECM connector.


Procedure1

c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
D50-103 (M+) - D18-6 (M+) Always Below 1 Ω
D50-135 (M-) - D18-5 (M-) Always Below 1 Ω
D50-103 (M+) or D18-6 (M+) - Body ground Always 10 kΩ or higher
D50-135 (M-) or D18-5 (M-) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG


Post-procedure1

d.

None.



OK

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.INSPECT THROTTLE BODY WITH MOTOR ASSEMBLY (VISUALLY CHECK THROTTLE VALVE)

Pre-procedure1

a.

Remove the throttle body with motor assembly.

HINT:

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>THROTTLE BODY>REMOVAL



Procedure1

b.

Check for contamination between the throttle valve and housing. If necessary, clean the throttle body with motor assembly. Also, check that the throttle valve moves smoothly.

OK:

Throttle valve is not contaminated with foreign objects and moves smoothly.



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NG

CLEAN THROTTLE BODY WITH MOTOR ASSEMBLY

4.REPLACE THROTTLE BODY WITH MOTOR ASSEMBLY

NEXT

5.PERFORM IDLE LEARNING
5.PERFORM IDLE LEARNING

NEXT

6.CLEAR DTC
6.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

7.CHECK WHETHER DTC OUTPUT RECURS (DTC P060E87, P210018, P210019, P210064, P211819 OR P211977)
7.CHECK WHETHER DTC OUTPUT RECURS (DTC P060E87, P210018, P210019, P210064, P211819 OR P211977)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Read the DTCs.

Powertrain > Engine > Trouble Codes
50001 372
OK:

DTCs are not output



Result:
Proceed to
OK
NG


Post-procedure1

c.

None.



OK

END

NG