Home › Engine / Hybrid System › 1KR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _091054 1KR-FE ENGINE CONTROL _0431746 SFI SYSTEM C

1KR-FE ENGINE CONTROL  SFI SYSTEM  P246300  Particulate Filter Restriction - Soot Accumulation Bank 1  


DESCRIPTION

Refer to DTC P244B00.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>P244B00

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory DTC Output from Priority
P246300 Particulate Filter Restriction - Soot Accumulation Bank 1 During high load operation, the Calculated Soot mass is higher than 20 g (1 trip detection logic). Front exhaust pipe assembly (GPF) Comes on* / -
*: The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.
DTC stored (Euro-OBD)
- (except Euro-OBD)
Engine A

MONITOR DESCRIPTION

When the accumulation ratio of the PM in the GPF (Gasoline Particulate Filter) is at the specified value or higher, output is limited during high load operation to prevent the GPF from rising to a high temperature. A DTC is stored at this time.

The MIL is illuminated when PM accumulation has progressed and protection of parts has become necessary.

MONITOR STRATEGY

Frequency of Operation Continuous

CONFIRMATION DRIVING PATTERN

A417745E03
2.979,3.25 2.833,3.25 2.833,3.25 2.667,2.885 false 5.406,3.25 5.531,3.25 5.531,3.25 5.688,2.885 false 0.563,2.406 2.229,2.729 1.667,0.323 10 false Ignition Switch ON 0.479,2.688 1.813,3.063 1.333,0.375 10 false Ignition Switch OFF 1.333,2.115 2.25,2.313 0.917,0.198 10 false Idling 1.229,1.167 2.302,1.365 1.073,0.198 10 false 60 km/h 2.125,2.01 2.448,2.281 0.323,0.271 10 false [A] 2.917,1.396 3.26,1.646 0.344,0.25 10 false [B] 1.906,2.938 2.51,3.323 0.604,0.385 10 false 5 minutes or more 3.01,3.167 3.948,3.448 0.938,0.281 10 false 30 seconds 4.667,3.156 5.51,3.438 0.844,0.281 10 false 30 seconds 6.146,3.135 6.51,3.406 0.365,0.271 10 false [C]

1.

Connect the GTS to the DLC3.

2.

Turn the ignition switch to ON.

3.

Turn the GTS on.

4.

Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

5.

Idle the engine for 5 minutes or more [A].

6.

Turn the ignition switch off and wait for at least 30 seconds.

7.

Start the engine.

8.

Repeat the pattern of accelerating the vehicle from rest to approximately 60 km/h (37 mph) [depress the accelerator pedal by a large amount at 2nd shift position] and then decelerating the vehicle 5 times [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


9.

Turn the ignition switch off and wait for at least 30 seconds.

10.

Turn the ignition switch to ON.

11.

Turn the GTS on.

12.

Enter the following menus: Powertrain / Engine / Trouble Codes [C].

13.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



14.

Enter the following menus: Powertrain / Engine / Data List / PM Deposition Ratio Bank1.

15.

Read the value displayed on the GTS.

HINT:
·

If the PM Deposition Ratio value is less than 100%, the system is normal.

·

If the PM Deposition Ratio value is 100% or higher, perform forced particulate filter rejuvenation.




CAUTION / NOTICE / HINT

HINT:
·

Clear the Vehicle Control History after completing repairs.

Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>VEHICLE CONTROL HISTORY

·

Read Freeze Frame Data using the GTS. The ECM records vehicle and driving condition information as Freeze Frame Data the moment a DTC is stored. When troubleshooting, Freeze Frame Data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CLEAR DTC

Pre-procedure1

a.

None.


Procedure1

b.

Clear the DTCs.

Powertrain > Engine > Clear DTCs
50002 372

Result:
Proceed to
NEXT


Post-procedure1

c.

Turn the ignition switch off and wait for at least 30 seconds.



NEXT

2.CLEAR VEHICLE CONTROL HISTORY
2.CLEAR VEHICLE CONTROL HISTORY
a.

Clear the Vehicle Control History (RoB).

Powertrain > Engine > Utility
Tester Display
Vehicle Control History (RoB)
50005 372 55
NOTICE:

By performing this procedure, all stored Vehicle Control History items will be cleared.



Result:
Proceed to
NEXT



NEXT

3.PERFORM PM REJUVENATE MODE
3.PERFORM PM REJUVENATE MODE

NEXT

END