DESCRIPTION (SFI SYSTEM)
Vehicle Control History is a function that captures and stores ECU data when triggered by specific vehicle behavior.
If the customer states that the engine stalled or will not start, it may be possible to diagnose the cause of the malfunction by checking the vehicle history information and freeze frame data.
The number of possible stored Freeze Frame Data sets, whether multi Freeze Frame Data is available, the number of freeze frame points, Freeze Frame Data items, the ECU internal range, etc., is different depending on the stored group.
The stored data items for Vehicle Control History Freeze Frame Data are different depending on the stored group. When the value of a data item does not change across all points, only the value of the detection point will be displayed. The contents of the Freeze Frame Data is almost the same as that of the Data List.
Click hereEngine / Hybrid System>1KR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST
PRECAUTIONS (SFI SYSTEM)
As Vehicle Control History may be overwritten whenever the trigger conditions are met, make sure to save Vehicle Control History before performing any inspections.
As Vehicle Control History may be stored when performing an Active Test, learning, etc., make sure to clear the Vehicle Control History before returning the vehicle to the customer.
CHECK VEHICLE CONTROL HISTORY (SFI SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
It is also possible to display Vehicle Control History during the Health Check, if "Store All Data" is selected.
| Stored Group | Number of Records | Number of Freeze Frame Points | Multi Freeze Frame Data Sampling Period | Note |
|---|---|---|---|---|
| 04 | 1 code
|
7 points (1 point at detection + 6 points before detection)
|
0.5 seconds | The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. |
| 05 | 2 codes
|
1 point (multi freeze frame data not available) | - | ·
The data can be cleared by using the GTS. ·
The data cannot be cleared by disconnecting the cable from the negative (-) battery terminal. |
| 09 | 1 code
|
7 points (1 point at detection + 3 points before detection + 3 points after detection)
|
0.5 seconds | The data can be cleared by using the GTS or by disconnecting the cable from the negative (-) battery terminal. |
| 0A | 4 codes
|
1 point (multi Freeze Frame Data not available) | - | The data can be cleared by using the GTS. |
Multi Freeze Frame Data makes it possible to display the engine condition (ECU data) both before and after the trigger detection point.
The number of available points differs depending on the stored group.
When the value of a data item does not change across all points, only the value at the detection point will be displayed.
Only 1 measurement point can be displayed for stored group 05 and 0A Freeze Frame Data.
CLEAR VEHICLE CONTROL HISTORY (SFI SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB) (Clear).
By performing this procedure, all stored Vehicle Control History items will be cleared.
| Tester Display |
|---|
| Vehicle Control History (RoB) |
VEHICLE CONTROL HISTORY FREEZE FRAME DATA (SFI SYSTEM)
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Utility / Vehicle Control History (RoB).
| Tester Display |
|---|
| Vehicle Control History (RoB) |
Select a vehicle control history item to access the applicable freeze frame data.
Check the Freeze Frame Data recorded with the Vehicle Control History.
VEHICLE CONTROL HISTORY (AIRBAG SYSTEM)
A part of the control history can be confirmed using the vehicle control history.
Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>AIRBAG SYSTEM>VEHICLE CONTROL HISTORY