Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW REGULATOR MOTOR (for Front Door) › 2020.07–2020.09
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0427203 POWER WINDOW REGULATOR MOTOR(for Front Door) A

WINDOW / GLASS  POWER WINDOW REGULATOR MOTOR(for Front Door)  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization or registration) that must be performed after parts are removed and installed, or replaced during the power window regulator motor removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedures Effect/Inoperative Function When Necessary Procedures are not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door window regulator sub-assembly

·

Power window regulator motor assembly

·

Door glass


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1:for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for RHD and LHD vehicles.

·

The procedure listed below is for LHD vehicles.

·

Use the same procedure for the RH and LH sides.

·

The procedure listed below is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67491A 3.REMOVE FRONT DOOR LOWER FRAME BRACKET GARNISH

Hide 74232 4.REMOVE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Driver Side)

Hide 74231 5.REMOVE POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH FRONT ARMREST BASE UPPER PANEL (for Front Passenger Side)

Hide 67655 6.REMOVE FRONT DOOR TRIM GARNISH

Hide 67601 7.REMOVE FRONT DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68171B 8.REMOVE FRONT DOOR GLASS INNER WEATHERSTRIP

Hide 67837A 9.REMOVE FRONT DOOR VENT SEAL

Hide 67855B 10.REMOVE FRONT DOOR PANEL PROTECTOR

Hide 67831 11.REMOVE FRONT DOOR SERVICE HOLE COVER

Hide 68101 12.REMOVE FRONT DOOR GLASS SUB-ASSEMBLY

Hide 13.REMOVE FRONT DOOR WINDOW REGULATOR ASSEMBLY

Hide 85710E 14.REMOVE POWER WINDOW REGULATOR MOTOR ASSEMBLY

a.
B563219

Remove the 3 bolts and power window regulator motor assembly.

NOTICE:
B576198C01
1.302,1.323 0.917,1.167 true 1.635,1.052 1.177,0.76 true 0.75,1.042 0.969,1.229 0.219,0.188 10 false *a 1,0.635 1.198,0.802 0.198,0.167 10 false *b
*a Protective Tape
*b Drum


Using a screwdriver with its tip wrapped in protective tape, carefully remove the power window regulator motor assembly while holding down the drum.