Home › Vehicle Exterior › WINDOW / GLASS › ROOF WINDOW FIX GLASS › from 2020.07
RM36W0E _59 Vehicle Exterior _088018 WINDOW / GLASS _0431794 ROOF WINDOW FIX GLASS A

WINDOW / GLASS  ROOF WINDOW FIX GLASS  INSTALLATION  


PROCEDURE

Hide 63201M 1.CLEAN NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY

a.
E268586

Clean the outer circumference of the No. 1 roof window glass sub-assembly with non-residue solvent.

NOTICE:
·

Do not touch the No. 1 roof window glass sub-assembly surface after cleaning it.

·

Be careful not to damage the glass.




Hide 63201M 2.INSTALL NO. 1 ROOF WINDOW GLASS SUB-ASSEMBLY

a.

Clean and shape the contact surface of the vehicle body.

i.
B582183C01
1.896,0.552 1.75,0.406 false 1.833,1.781 1.708,1.604 false 1.948,0.49 2.167,0.677 0.219,0.188 10 false *1 1.885,1.719 2.198,1.875 0.313,0.156 10 false *1
*1 Roof Panel
V100155

Adhesive


Using a knife, cut away excess adhesive on the contact surface of the vehicle body as shown in the illustration.

NOTICE:

Leave as much adhesive on the vehicle body as possible.



ii.

Clean the contact surface of the vehicle body with a piece of cloth saturated with non-residue solvent.



b.

Position the No. 1 roof window glass sub-assembly.

i.

Using suction cups, place the No. 1 roof window glass sub-assembly in the correct position.


ii.

Check that the whole contact surface of the No.1 roof window glass sub-assembly rim is perfectly even.


iii.
B582227C01
1.271,0.729 0.667,0.448 0.667,0.448 1.031,0.427 true 0.49,0.333 0.802,0.49 0.313,0.156 10 false *a
*a Matchmarks


Align the matchmarks on the No. 1 roof window glass sub-assembly and vehicle body.

NOTICE:

Check that the roof window clips are engaged to the vehicle body correctly.



iv.

Using suction cups, remove the No. 1 roof window glass sub-assembly.


v.

Using a brush, coat the installation surface on the vehicle body with primer M.

NOTICE:
·

Do not coat the adhesive with primer M.

·

Do not apply too much primer M.

·

Allow the primer M to dry for 3 minutes or more.

·

Throw away any leftover primer M.



HINT:

If an area other than specified is coated by accident, wipe off the primer M with a clean piece of cloth before it dries.




c.

Using a brush or sponge, coat the adhesive application area with primer G.

B582180C01
1.333,0.198 1.583,0.396 0.25,0.198 10 false *a 1.865,0.469 2.031,0.667 0.167,0.198 10 false A 2.26,0.458 2.396,0.635 0.135,0.177 10 true A 4.76,0.479 4.896,0.656 0.135,0.177 10 true C 5.167,0.479 5.333,0.677 0.167,0.198 10 false C 3.917,1.49 4.052,1.667 0.135,0.177 10 true B 3.927,1.896 4.063,2.073 0.135,0.177 10 false B 0.417,2.333 0.75,2.5 0.333,0.167 10 false A-A 2.833,2.333 3.167,2.5 0.333,0.167 10 false B-B 5,2.333 5.333,2.5 0.333,0.167 10 false C-C 1.135,2.552 1.385,2.75 0.25,0.198 10 false a 3.708,2.542 3.958,2.74 0.25,0.198 10 false b 5.906,2.563 6.156,2.76 0.25,0.198 10 false c
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Primer G - -


Standard:
Area Specified Condition
a 30.5 mm (1.2008 in.) or more
b 18.9 mm (0.7441 in.) or more
c 19.8 mm (0.7795 in.) or more


NOTICE:
·

Do not apply too much primer G.

·

Allow the primer G to dry for 3 minutes or more.

·

Throw away any leftover primer G.



HINT:

If an area other than specified is coated by accident, wipe off the primer G with a clean piece of cloth before it dries.



d.

Apply adhesive to the No.1 roof window glass sub-assembly.

Adhesive:

Toyota Genuine Windshield Glass Adhesive (High modulus type) or equivalent


i.
B214800C28
1.198,0.438 1.385,0.5 false 0.5,0.625 0.656,0.823 0.156,0.198 10 false a 1.344,1.365 1.5,1.563 0.156,0.198 10 false a 1.115,0.885 1.271,1.083 0.156,0.198 10 false b 0.76,1 0.917,1.198 0.156,0.198 10 false b 1.406,0.438 1.646,0.615 0.24,0.177 10 false *a
*a Cartridge Nozzle
V100155

Adhesive


Cut off the tip of the cartridge nozzle as shown in the illustration.

Standard:
Area Specified Condition
a 12 to 15 mm (0.472 to 0.591 in.)
b 8.0 to 11 mm (0.315 to 0.433 in.)




e.

Load the sealer gun with the cartridge.


f.

Apply adhesive to the No. 1 roof window glass sub-assembly as shown in the illustration.

B582181C01
1.333,0.198 1.583,0.396 0.25,0.198 10 false *a 1.865,0.469 2.031,0.667 0.167,0.198 10 false A 2.26,0.458 2.396,0.635 0.135,0.177 10 true A 4.76,0.479 4.896,0.656 0.135,0.177 10 true C 5.167,0.479 5.333,0.677 0.167,0.198 10 false C 3.917,1.49 4.052,1.667 0.135,0.177 10 true B 3.927,1.896 4.063,2.073 0.135,0.177 10 false B 0.417,2.333 0.75,2.5 0.333,0.167 10 false A-A 2.833,2.333 3.167,2.5 0.333,0.167 10 false B-B 5,2.333 5.333,2.5 0.333,0.167 10 false C-C 0.969,2.396 1.219,2.594 0.25,0.198 10 false a 3.833,2.542 4.083,2.74 0.25,0.198 10 false c 5.958,2.531 6.208,2.729 0.25,0.198 10 false d 1.24,2.656 1.49,2.854 0.25,0.198 10 false b
*a Back Side of No. 1 Roof Window Glass Sub-assembly - -
V100155

Adhesive Application Area - -


Standard:
Area Specified Condition
a 14.4 mm (0.5669 in.)
b 9.1 mm (0.3583 in.)
c 11.9 mm (0.4685 in.)
d 12.8 mm (0.5039 in.)



g.

Install the No. 1 roof window glass sub-assembly.

i.
B582184C02
1.281,0.719 0.677,0.438 0.677,0.438 1.031,0.427 true 0.521,0.323 0.833,0.479 0.313,0.156 10 false *a
*a Matchmarks


Using suction cups, position the No. 1 roof window glass sub-assembly so that the matchmarks are aligned, and press it in gently along the rim.

NOTICE:
·

Check that the roof window clips are engaged to the vehicle body correctly.

·

Check the clearance between the vehicle body and No. 1 roof window glass sub-assembly.




ii.

Lightly press the outer surface of the No. 1 roof window glass sub-assembly to ensure a close fit and engage the roof window clips.

HINT:

Press the glass with force of 98 N (10 kgf, 22.0 lbf) or more.




h.

Using a scraper, remove any excess or protruding adhesive.


i.

Hold the No. 1 roof window glass sub-assembly using protective tape until the applied adhesive becomes hard.

HINT:

Follow the instructions supplied by the adhesive manufacturer or in the corresponding instruction manual for the minimum amount of time necessary to wait before driving the vehicle.



Hide 3.INSPECT FOR LEAK

a.

After the adhesive has hardened, apply water from the outside of the vehicle. Check that no water leaks into the cabin.


b.

If water leaks into the cabin, allow the water to dry and add adhesive.


c.

Remove the protective tape.


Hide 75552 4.INSTALL ROOF DRIP SIDE FINISH MOULDING LH

Hide 63310 5.INSTALL ROOF HEADLINING ASSEMBLY