Home › Engine / Hybrid System › STOP AND START › STOP AND START SYSTEM › from 2020.07
RM36W0E _51 Engine / Hybrid System _090986 STOP AND START _0432127 STOP AND START SYSTEM C

STOP AND START  STOP AND START SYSTEM  P186262  Clutch Pedal Switch Signal Compare Failure  


DESCRIPTION

There are 2 clutch pedal switches for the clutch pedal. The clutch switch assembly (for upper) is used for stopping and restarting of the engine by stop and start control. During the stop and start control, the clutch start switch assembly (for lower) is used only when the clutch switch assembly (for upper) is stuck on or the fail-safe function is activated.

DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory Note
P186262 Clutch Pedal Switch Signal Compare Failure Both of the following conditions continue for 0.5 seconds or more (1 trip detection logic):
·

Clutch start switch assembly (for lower) is on.

·

Clutch switch assembly (for upper) is on.


·

Clutch start switch assembly (for lower)

·

Clutch switch assembly (for upper)

·

Wire harness or connector

·

Engine stop and start ECU


Blinks DTC stored SAE Code: P1862

CONFIRMATION DRIVING PATTERN

HINT:

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR


CONFIRMATION AFTER TROUBLESHOOTING


HINT:
·

If the cable is disconnected from the auxiliary battery terminal, stop and start control is prohibited until refresh charge is completed.

In this case, let the vehicle idle with the auxiliary battery fluid temperature at 11°C (51°F) or higher for 5 to 60 minutes to complete the refresh charge. (The refresh charge is complete when the Data List item Status of Battery Charge Control changes from "Refresh Charge Mode".)

·

If the GTS is not available and the Data List item Status of Battery Charge Control cannot be checked, charge the auxiliary battery by idling the engine for approximately 5 to 60 minutes or driving the vehicle, and then drive the vehicle and check that stop and start control operates.

If the engine is started with the hood open, the system determines that a jump start has occurred. Therefore, make sure that the hood is closed before starting the engine and driving the vehicle.

·

After the refresh charge completes, turn the ignition switch off, wait for at least 30 seconds, and then start the engine again.

If the vehicle enters refresh charge mode again while the engine is idling, the initial refresh charge did not properly complete, so wait for the refresh charge to complete.

·

Allow the engine to idle for 3 minutes after the engine warms up and check that the engine speed is within 50 rpm of the target idle speed.



a.

Clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Clear DTCs
50002 227

b.

Start the engine.


c.
A206932E04
1.302,1.948 1.302,2.708 false 1.594,1.948 1.594,2.708 false 1.323,2.167 1.865,2.167 false 1.365,2.208 1.323,2.167 1.323,2.167 1.365,2.135 false 1.823,2.135 1.865,2.167 1.865,2.167 1.823,2.208 false 1.708,2.167 1.958,2.74 false 1.469,2.167 1.208,2.74 false 1.542,2.135 1.594,2.167 1.594,2.167 1.542,2.208 false 1.635,2.208 1.594,2.167 1.594,2.167 1.635,2.135 false 1.875,1.927 1.875,2.708 false 0.135,0.115 1.458,0.302 1.323,0.188 10 Clutch Switch Signal 1.99,2.719 3.135,2.906 1.146,0.188 10 1 second or more 0.281,2.719 1.052,3.031 0.771,0.313 10 1 second or more 0.583,1.177 0.833,1.333 0.25,0.156 10 ON 0.583,1.854 0.896,2.01 0.313,0.156 10 OFF

Fully depress the clutch pedal for 1 second or more. Release the clutch pedal and wait for at least 1 second.


d.

Repeat the previous step 3 times.


e.

Check that no DTCs are output.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR

Powertrain > Stop and Start > Trouble Codes
50001 227


STOP AND START SYSTEM OPERATION CHECK


Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>OPERATION CHECK


WIRING DIAGRAM

A456553E01
0.146,0.104 2.667,0.396 2.521,0.292 12 false for M15A-FKS: 0.625,2.583 1.917,3.198 1.292,0.615 10 false EFI-MAIN NO. 1 4.573,2.719 4.99,2.958 0.417,0.24 10 false NSW 4.031,3.563 4.448,3.802 0.417,0.24 10 false A54 6.021,5.188 6.438,5.427 0.417,0.24 10 false A67 3.708,2.719 4.125,2.958 0.417,0.24 10 false 15 5,2.604 5.417,2.844 0.417,0.24 10 false 23 5,2.958 5.417,3.198 0.417,0.24 10 false 30 3.948,2.833 4.365,3.073 0.417,0.24 10 false MREL 4.625,3.094 5.042,3.333 0.417,0.24 10 false STA 0.156,4.521 0.573,4.76 0.417,0.24 10 false A 5.25,4.5 5.667,4.74 0.417,0.24 10 false B 3.24,2.719 3.656,2.958 0.417,0.24 10 false 1 2.458,2.729 2.875,2.969 0.417,0.24 10 false 2 3.802,1.458 4.219,1.698 0.417,0.24 10 false A65 3.792,1.635 6.115,1.896 2.323,0.26 10 false Clutch Switch Assembly (for Upper) 3.646,1 4.063,1.24 0.417,0.24 10 false 1 4.917,1 5.333,1.24 0.417,0.24 10 false 2 6.01,5.375 7.125,5.719 1.115,0.344 10 false Engine Stop and Start ECU 6.198,1.115 6.615,1.354 0.417,0.24 10 false CLU 5.948,0.99 6.365,1.229 0.417,0.24 10 false 11 2.625,1.865 3.51,2.083 0.885,0.219 10 false EFI NO. 3 3.219,2.302 3.635,2.542 0.417,0.24 10 false 3 2.448,2.302 2.865,2.542 0.417,0.24 10 false 5 5.615,4.521 6.031,4.76 0.417,0.24 10 false C 3.844,1.01 4.26,1.25 0.417,0.24 10 false CL+ 4.573,1 4.99,1.24 0.417,0.24 10 false CL- 2.365,3.177 3.656,3.792 1.292,0.615 10 false EFI-MAIN NO. 1 4.021,3.74 4.438,3.979 0.417,0.24 10 false ECM

A456556E01
0.146,0.094 2.667,0.385 2.521,0.292 12 false for 1KR-FE: 0.625,2.583 1.917,3.198 1.292,0.615 10 false EFI-MAIN NO. 1 4.573,2.719 4.99,2.958 0.417,0.24 10 false NSW 3.594,2.823 4.01,3.063 0.417,0.24 10 false A55 6.021,5.188 6.438,5.427 0.417,0.24 10 false A67 3.667,2.646 4.083,2.885 0.417,0.24 10 false 9 5.021,2.552 5.438,2.792 0.417,0.24 10 false 111 5.042,2.917 5.458,3.156 0.417,0.24 10 false 46 3.948,2.833 4.365,3.073 0.417,0.24 10 false MREL 4.625,3.094 5.042,3.333 0.417,0.24 10 false STA 0.156,4.521 0.573,4.76 0.417,0.24 10 false A 5.406,4.49 5.823,4.729 0.417,0.24 10 false B 3.229,2.708 3.646,2.948 0.417,0.24 10 false 1 2.427,2.719 2.844,2.958 0.417,0.24 10 false 2 3.802,1.458 4.219,1.698 0.417,0.24 10 false A65 3.792,1.635 6.115,1.896 2.323,0.26 10 false Clutch Switch Assembly (for Upper) 3.646,1 4.063,1.24 0.417,0.24 10 false 1 4.917,1 5.333,1.24 0.417,0.24 10 false 2 6.01,5.375 7.125,5.719 1.115,0.344 10 false Engine Stop and Start ECU 6.198,1.115 6.615,1.354 0.417,0.24 10 false CLU 5.948,0.99 6.365,1.229 0.417,0.24 10 false 11 2.625,1.865 3.51,2.083 0.885,0.219 10 false EFI NO. 3 2.427,2.302 2.844,2.542 0.417,0.24 10 false 3 3.229,2.292 3.646,2.531 0.417,0.24 10 false 5 5.75,4.5 6.167,4.74 0.417,0.24 10 false C 3.844,1.01 4.26,1.25 0.417,0.24 10 false CL+ 4.573,1 4.99,1.24 0.417,0.24 10 false CL- 2.365,3.177 3.656,3.792 1.292,0.615 10 false EFI-MAIN NO. 1 4.208,3.604 4.625,3.844 0.417,0.24 10 false ECM 5.01,3.083 5.427,3.323 0.417,0.24 10 false A55 5.021,2.729 5.438,2.969 0.417,0.24 10 false D50

A456554E02
0.083,0.083 2.167,0.375 2.083,0.292 12 false w/ Entry and Start System: 2.031,6 3.583,6.49 1.552,0.49 10 false Certification ECU (Smart Key ECU Assembly) 2.052,5.823 2.365,6.01 0.313,0.188 10 false H45 0.25,0.635 0.563,0.823 0.313,0.188 10 false A 5.75,0.594 6.063,0.781 0.313,0.188 10 false C 0.406,2.094 1.698,2.292 1.292,0.198 10 false BATT-MAIN NO. 1 2.49,5.417 2.958,5.646 0.469,0.229 10 false STAR 2.969,4.51 3.281,4.698 0.313,0.188 10 false 3 2.958,5.271 3.271,5.458 0.313,0.188 10 false 10 5.01,3.219 5.323,3.406 0.313,0.188 10 false 2 5.51,4.521 5.823,4.708 0.313,0.188 10 false 2 4.281,3.219 4.594,3.406 0.313,0.188 10 false 1 5.938,3.198 6.25,3.385 0.313,0.188 10 false 21 6.198,4.667 6.51,4.854 0.313,0.188 10 false CLL 6.208,3.323 6.521,3.51 0.313,0.188 10 false STA 3.49,4.854 3.802,5.042 0.313,0.188 10 false A64 3.479,5.063 6.031,5.313 2.552,0.25 10 false Clutch Start Switch Assembly 5.938,4.51 6.25,4.698 0.313,0.188 10 false 17 5.833,6.135 6.271,6.333 0.438,0.198 10 false A67 5.833,6.313 6.948,6.771 1.115,0.458 10 false Engine Stop and Start ECU 1.844,3.063 2.302,3.26 0.458,0.198 10 false D80 2.208,3.052 2.667,3.25 0.458,0.198 10 false B 4.406,3.667 5.125,3.865 0.719,0.198 10 false ST NO. 1 2.198,3.458 3.479,3.729 1.281,0.271 10 false Starter Assembly 1.906,2.854 2.219,3.042 0.313,0.188 10 false 1 3.51,2.375 3.823,2.563 0.313,0.188 10 false 1 5.948,5.74 6.26,5.927 0.313,0.188 10 false 6 6.198,5.885 6.802,6.146 0.604,0.26 10 false DGND 5.354,0.604 5.667,0.792 0.313,0.188 10 false B 4.406,1.938 5.125,2.135 0.719,0.198 10 false ST NO. 1 3.448,2.573 3.906,2.771 0.458,0.198 10 false D55 3.521,2.802 3.833,2.99 0.313,0.188 10 false 1 3.448,3 3.906,3.198 0.458,0.198 10 false D54 3.167,3 3.625,3.198 0.458,0.198 10 false ST 2.917,2.583 3.406,2.823 0.49,0.24 10 false ZYV*1 4.271,2.885 4.583,3.073 0.313,0.188 10 false 3 5.01,2.896 5.323,3.083 0.313,0.188 10 false 5 3.885,2.469 4.198,2.656 0.313,0.188 10 false *1 3.656,4.5 3.969,4.688 0.313,0.188 10 false 1 5.313,4.531 5.771,4.729 0.458,0.198 10 false B 3.875,4.531 4.333,4.729 0.458,0.198 10 false L 2.583,4.646 2.896,4.833 0.313,0.188 10 false STA 0.594,5.25 1.188,5.896 0.594,0.646 10 false Auxiliary Battery 4,6.323 5.323,6.625 1.323,0.302 10 false *1: for M15A-FKS

A456555E02
0.073,0.083 2.156,0.375 2.083,0.292 12 false w/o Entry and Start System: 1.625,6.344 4.552,6.552 2.927,0.208 10 false Ignition or Starter Switch Assembly 1.646,6.156 1.958,6.344 0.313,0.188 10 false H54 0.25,0.531 0.563,0.719 0.313,0.188 10 false A 5.729,0.49 6.042,0.677 0.313,0.188 10 false C 0.396,1.99 1.688,2.188 1.292,0.198 10 false BATT-MAIN NO. 1 2.823,5.802 3.292,6.031 0.469,0.229 10 false ST2 1.865,5.813 2.177,6 0.313,0.188 10 false 1 3.177,5.813 3.49,6 0.313,0.188 10 false 4 5.021,3.104 5.333,3.292 0.313,0.188 10 false 2 5.125,5.052 5.438,5.24 0.313,0.188 10 false 2 4.271,3.115 4.583,3.302 0.313,0.188 10 false 1 5.948,4.656 6.26,4.844 0.313,0.188 10 false 21 6.198,5.177 6.51,5.365 0.313,0.188 10 false CLL 6.198,4.771 6.563,5.021 0.365,0.25 10 false STA 3.75,5.531 4.063,5.719 0.313,0.188 10 false A64 3.74,5.719 5.646,6.177 1.906,0.458 10 false Clutch Start Switch Assembly 5.938,5.063 6.25,5.25 0.313,0.188 10 false 17 5.854,5.948 6.292,6.146 0.438,0.198 10 false A67 5.833,6.135 6.948,6.594 1.115,0.458 10 false Engine Stop and Start ECU 1.854,2.677 2.313,2.875 0.458,0.198 10 false D80 2.208,2.677 2.667,2.875 0.458,0.198 10 false B 4.417,3.563 5.135,3.76 0.719,0.198 10 false ST NO. 1 2.292,3.354 3.573,3.625 1.281,0.271 10 false Starter Assembly 1.917,2.479 2.229,2.667 0.313,0.188 10 false 1 3.51,2.26 3.823,2.448 0.313,0.188 10 false 1 5.979,5.448 6.292,5.635 0.313,0.188 10 false 6 6.188,5.542 6.792,5.802 0.604,0.26 10 false DGND 5.354,0.49 5.667,0.677 0.313,0.188 10 false B 4.438,1.813 5.156,2.01 0.719,0.198 10 false ST NO. 1 3.448,2.469 3.906,2.667 0.458,0.198 10 false D55 3.521,2.688 3.833,2.875 0.313,0.188 10 false 1 3.448,2.885 3.906,3.083 0.458,0.198 10 false D54 3.167,2.885 3.625,3.083 0.458,0.198 10 false ST 2.948,2.469 3.438,2.708 0.49,0.24 10 false ZYV*1 4.271,2.802 4.583,2.99 0.313,0.188 10 false 3 5.01,2.792 5.323,2.979 0.313,0.188 10 false 5 3.885,2.365 4.198,2.552 0.313,0.188 10 false *1 3.771,5.052 4.083,5.24 0.313,0.188 10 false 1 4.885,5.063 5.344,5.26 0.458,0.198 10 false B 3.979,5.073 4.438,5.271 0.458,0.198 10 false L 2.385,4.948 2.698,5.135 0.313,0.188 10 false AM2 0.417,4.125 1.708,4.323 1.292,0.198 10 false INP STD NO. 1-3 0.583,5.083 1.156,5.646 0.573,0.563 10 false Auxiliary Battery 2.063,5.813 2.479,6.073 0.417,0.26 10 false AM2 4.104,6.469 5.469,6.688 1.365,0.219 10 false *1: for M15A-FKS

CAUTION / NOTICE / HINT

NOTICE:
·

Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>REGISTRATION

·

After replacing the engine stop and start ECU or airbag sensor assembly, clear and calibrate the deceleration sensor zero point in the engine stop and start ECU.

Click here



HINT:
·

Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>FREEZE FRAME DATA

·

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click hereEngine / Hybrid System>STOP AND START>STOP AND START SYSTEM>DTC CHECK / CLEAR



PROCEDURE

1.READ VALUE USING GTS (CLUTCH UPPER SW AND CLUTCH LOWER SW)
a.

Enter the following menus: Powertrain / Stop and Start / Data List / Clutch Upper SW and Clutch Lower SW.

Powertrain > Stop and Start > Data List
Tester Display
Clutch Upper SW
Clutch Lower SW
50003 227 10,11

b.

Depress the clutch pedal and read the values displayed on the GTS.

OK:
Tester Display Condition Normal Condition
Clutch Upper SW Fully Depressed OFF
Clutch Lower SW Fully Depressed ON
Clutch Upper SW Fully Released ON
Clutch Lower SW Fully Released OFF



Result:
Proceed to
NG
OK



NG

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

OK

2.INSPECT CLUTCH START SWITCH ASSEMBLY (FOR LOWER)
a.

Inspect the clutch start switch assembly (for lower).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)

NG

REPLACE CLUTCH START SWITCH ASSEMBLY (FOR LOWER)

3.INSPECT CLUTCH SWITCH ASSEMBLY (FOR UPPER)
a.

Inspect the clutch switch assembly (for upper).

Click hereDrivetrain>CLUTCH>CLUTCH PEDAL SWITCH>INSPECTION


Result:
Proceed to
OK
NG



OK

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))

NG

REPLACE CLUTCH SWITCH ASSEMBLY (FOR UPPER)

4.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH START SWITCH ASSEMBLY (FOR LOWER))
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A64 clutch start switch assembly (for lower) connector.


c.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.*1

*1: w/ Entry and Start System



d.

Disconnect the H54 ignition or starter switch assembly connector.*1

*1: w/o Entry and Start System



e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-17 (CLL) - A64-2 (B) Always Below 1 Ω
A67-17 (CLL) - Body ground and other terminals Always 10 kΩ or higher
A64-2 (B) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK HARNESS AND CONNECTOR (ENGINE START AND STOP ECU - CLUTCH SWITCH ASSEMBLY (FOR UPPER))
a.

Disconnect the A67 engine stop and start ECU connector.


b.

Disconnect the A65 clutch switch assembly (for upper) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A67-11 (CLU) - A65-2 (CL-) Always Below 1 Ω
A67-11 (CLU) - Body ground and other terminals Always 10 kΩ or higher
A65-2 (CL-) - Body ground and other terminals Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR