Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) J

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  VSC OFF Switch Circuit  


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.

Pressing the VSC OFF switch (combination switch assembly) turns off TRC operation, and pressing and holding this switch turns off TRC and VSC operation. If TRC and VSC operations are turned off, "Traction Control Turned OFF" will be displayed on the multi-information display and the VSC OFF indicator light will come on.

WIRING DIAGRAM

C397530E49
0.906,0.927 1.521,1.125 0.615,0.198 10 false CANL 0.896,1.74 1.51,1.938 0.615,0.198 10 false CANH 0.083,3.896 0.698,4.094 0.615,0.198 10 false H6 0.073,4.063 2,4.344 1.927,0.281 10 false Combination Meter Assembly 1.406,0.75 1.719,0.948 0.313,0.198 10 false 25 1.406,1.552 1.719,1.75 0.313,0.198 10 false 9 5.094,0.75 5.406,0.948 0.313,0.198 10 false 10 5.115,1.563 5.427,1.76 0.313,0.198 10 false 11 4.729,2.625 5.042,2.823 0.313,0.198 10 false 7 4.51,2.823 4.823,3.021 0.313,0.198 10 false + 3.833,2.833 4.146,3.031 0.313,0.198 10 false E 3.615,2.615 3.927,2.813 0.313,0.198 10 false 5 5.104,2.625 5.417,2.823 0.313,0.198 10 false 20 5.375,0.927 5.99,1.125 0.615,0.198 10 false CANL 5.375,1.74 5.99,1.938 0.615,0.198 10 false CANH 5.365,2.844 5.979,3.042 0.615,0.198 10 false CSW 3.292,3.104 3.906,3.302 0.615,0.198 10 false H18 3.281,3.26 5.229,3.667 1.948,0.406 10 false VSC OFF Switch (Combination Switch Assembly) 2.906,4.333 5,4.594 2.094,0.26 10 false : CAN Communication Line 6.49,2.74 7.104,2.938 0.615,0.198 10 false IC 5.302,3.948 5.917,4.146 0.615,0.198 10 false A37 5.302,4.104 6.854,4.49 1.552,0.385 10 false Skid Control ECU (Brake Actuator Assembly)

CAUTION / NOTICE / HINT

NOTICE:

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY


PROCEDURE

1.READ VALUE USING GTS (TRC(TRAC)/VSC OFF MODE)
a.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Chassis > Brake > Data List
Tester Display
TRC(TRAC)/VSC OFF Mode
50003 435 45

b.

Check the indicator light and mode condition on the GTS changes according to VSC OFF switch (combination switch assembly) operation.

Standard:
Switch Operation Mode Condition Display Multi-information Display ("Traction Control Turned OFF") VSC OFF Indicator Light
Not pressed Normal mode (TRC(TRAC) ON/VSC ON) Not displayed Does not come on
Pressing the VSC OFF switch (combination switch assembly) TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) Displayed Does not come on
Pressing and holding the VSC OFF switch (combination switch assembly) VSC OFF mode (TRC(TRAC) OFF/VSC OFF) Displayed Comes on



Result:
Result Proceed to
Indicator light and mode condition display do not change A
Mode condition display is normal, but indicator light does not change B
Indicator light and mode condition display are normal C



A

2.INSPECT COMBINATION SWITCH ASSEMBLY

B

C

2.INSPECT COMBINATION SWITCH ASSEMBLY

Pre-procedure1

a.
C398937C02
1.406,1.813 1.604,1.385 true 2.135,1.802 1.927,1.375 true 0.146,0.146 0.458,0.302 0.313,0.156 10 false *a 2.156,1.854 2.313,2.052 0.156,0.198 10 false E 1.354,1.833 1.51,2.031 0.156,0.198 10 false +
*a Component without harness connected
(VSC OFF Switch (Combination Switch Assembly))


Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the H18 VSC OFF switch (combination switch assembly) connector.


c.

Check both the connector case and the terminal for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-7 (+) - H18-5 (E) Switch pushed Below 50 Ω
H18-7 (+) - H18-5 (E) Switch not pushed 10 kΩ or higher



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

NG

REPLACE COMBINATION SWITCH ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (COMBINATION SWITCH ASSEMBLY - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connector.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Disconnect the H18 VSC OFF switch (combination switch assembly) connector.


d.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

e.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H18-7 (+) - A37-20 (CSW) Always Below 1 Ω
H18-7 (+) or A37-20 (CSW) - Body ground Always 10 kΩ or higher
H18-5 (E) - Body ground Always Below 1 Ω



Post-procedure1

f.

None


Result:
Proceed to
OK
NG



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR