Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C00611C  Lateral Acceleration Sensor Circuit Voltage Out of Range  


DESCRIPTION

The skid control ECU (brake actuator assembly) receives signals from the yaw rate and acceleration sensor (airbag sensor assembly) via CAN communication.

HINT:

If there is a malfunction in the bus lines between the yaw rate and acceleration sensor (airbag sensor assembly) and the CAN communication system, DTC U012587 is output. When U012587 is output with C00611C, inspect and repair the trouble areas indicated by U012587 first.


These DTCs may be stored if one of the following occurs:

·

Yaw rate and acceleration sensor circuit malfunction.

·

Yaw rate and acceleration sensor (airbag sensor assembly) installation abnormality.

·

Yaw rate and acceleration sensor signal malfunction.


DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C00611C Lateral Acceleration Sensor Circuit Voltage Out of Range
·

While the vehicle is stopped, the lateral acceleration signal output value is outside the range of -7 to 7 m/s2 for 0.1 second or more.

·

When the vehicle is being driven straight ahead at a constant speed, the difference between the lateral acceleration signal output value and the control value calculated by the skid control ECU is outside the range of -5 to 5 m/s2 for 0.5 second or more.

·

When the vehicle is being driven at varying speeds and steered, the difference between the lateral acceleration signal output value and the control value calculated by the skid control ECU is outside the range of -11 to 11 m/s2 for 1.75 seconds or more.


·

Acceleration sensor (airbag sensor assembly)

·

Acceleration sensor circuit

·

Acceleration sensor (airbag sensor assembly) installation


Brake

WIRING DIAGRAM

C275041E87
0.802,0.708 1.417,0.906 0.615,0.198 10 false CAFL 6.052,0.719 6.667,0.917 0.615,0.198 10 false CANL 0.792,1.323 1.406,1.521 0.615,0.198 10 false CAFH 6.042,1.323 6.656,1.521 0.615,0.198 10 false CANH 0.938,1.938 1.229,2.177 0.292,0.24 10 false IGR 0.979,2.552 1.292,2.75 0.313,0.198 10 false E1 0.958,3.167 1.271,3.365 0.313,0.198 10 false E2 1.292,0.552 1.604,0.75 0.313,0.198 10 false 27 1.292,1.156 1.604,1.354 0.313,0.198 10 false 26 1.302,1.844 1.615,2.042 0.313,0.198 10 false 36 1.292,2.448 1.604,2.646 0.313,0.198 10 false 33 1.302,3.052 1.615,3.25 0.313,0.198 10 false 32 5.76,0.542 6.073,0.74 0.313,0.198 10 false 10 5.76,1.146 6.031,1.365 0.271,0.219 10 false 11 2.135,2.094 2.906,2.281 0.771,0.188 10 false A/BAG-IGR 3.927,1.938 5.385,2.156 1.458,0.219 10 false from IGR-NO. 1 Relay 0.063,3.896 0.521,4.094 0.458,0.198 10 false H14 0.052,4.063 2.208,4.531 2.156,0.469 10 false Yaw Rate and Acceleration Sensor (Airbag Sensor Assembly) 5.573,3.938 7.125,4.344 1.552,0.406 10 false Skid Control ECU (Brake Actuator Assembly) 5.583,3.76 6.042,3.958 0.458,0.198 10 false A37 3.677,3.406 5.479,3.635 1.802,0.229 10 false : CAN Communication Line

CAUTION / NOTICE / HINT

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing or reinstalling the yaw rate and acceleration sensor (airbag sensor assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY


PROCEDURE

1.CHECK DTC

Result:
Result Proceed to
CAN communication system DTCs are not output A
CAN communication system DTCs are output B



A

2.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G, YAW RATE SENSOR VALUE)

B

2.READ VALUE USING GTS (LATERAL G, FORWARD AND REARWARD G, YAW RATE SENSOR VALUE)

Pre-procedure1

a.

Operate the GTS to confirm the Data List.


Procedure1

b.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Lateral G Lateral G Min.: -25.105 m/s2
Max.: 24.908 m/s2
Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and Rearward G Min.: -25.105 m/s2
Max.: 24.908 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s
Max.: 127°/s
Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Chassis > Brake > Data List
Tester Display
Lateral G
Forward and Rearward G
Yaw Rate Sensor Value
50003 435 25,26,29

c.

Check the yaw rate and acceleration sensor (airbag sensor assembly) output value displayed on the GTS.

OK:

The yaw rate and acceleration sensor (airbag sensor assembly) output value is normal.



Post-procedure1

d.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
3.CHECK AIRBAG SENSOR ASSEMBLY INSTALLATION
a.

Check that the yaw rate and acceleration sensor (airbag sensor assembly) has been installed properly.

HINT:

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>CENTER AIRBAG SENSOR ASSEMBLY>INSTALLATION


OK:

The yaw rate and acceleration sensor (airbag sensor assembly) is tightened to the specified torque.

The yaw rate and acceleration sensor (airbag sensor assembly) is not installed in a tilted position.



Result:
Proceed to
OK
NG



OK

NG