The skid control ECU (brake actuator assembly) stores this DTC when the previously learned values in the VSC system and engine information sent from the ECM are inconsistent, or when the learning has not completed after the skid control ECU (brake actuator assembly) is replaced with a new one.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C128854 | Matching of ECUs Missing Calibration | ECM does not match. | ECM | Brake |
After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and store system information memorization.
Check if the ECM or brake actuator assembly had been replaced before the DTC was recorded.
| Result | Proceed to |
|---|---|
| Both the ECM and brake actuator assembly are not replaced | A |
| The ECM is replaced | B |
| The brake actuator assembly is replaced | C |
A
B
C
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C128854 is not output | A |
| C128854 is output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL
Check the vehicle specification.
| Result | Proceed to |
|---|---|
| 1KR-FE | A |
| M15A-FKS | B |
A
B
Perform system variant learning.
| Tester Display |
|---|
| Calibration |
System variant learning is automatically performed immediately after Test Mode is entered.
If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.
If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C128854 is not output | A |
| C128854 is output | B |
A
B
Perform system variant learning.
| Tester Display |
|---|
| Calibration |
System variant learning is automatically performed immediately after Test Mode is entered.
If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.
If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C128854 is not output | A |
| C128854 is output | B |
A
B
Perform system variant learning.
| Tester Display |
|---|
| Calibration |
System variant learning is automatically performed immediately after Test Mode is entered.
If learning has not yet been performed, the slip indicator light will remain on and DTC C128854 will be stored.
If system variant learning is not successful, the warning lights will not blink in the Test Mode pattern and DTC C128854 will not be cleared.
| Proceed to |
|---|
| NEXT |
NEXT
Pre-procedure1
None
Procedure1
Operate the GTS to clear the codes.
Post-procedure1
Turn the ignition switch off.
| Proceed to |
|---|
| NEXT |
NEXT
Operate the GTS to read the DTCs.
Check if the same DTC is output.
| Result | Proceed to |
|---|---|
| C128854 is not output | A |
| C128854 is output | B |
A
B
for LHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model LHD)>REMOVAL
for RHD: Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for Gasoline Model TMMF Made RHD)>REMOVAL