The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during engine unit removal/installation are shown below.
89467B
1.REMOVE AIR FUEL RATIO SENSOR
89481B
2.REMOVE DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)
25733A
3.REMOVE NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)
17167
4.REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
17118
5.REMOVE MANIFOLD STAY
17141
6.REMOVE EXHAUST MANIFOLD
22030
7.REMOVE THROTTLE BODY WITH MOTOR ASSEMBLY
22271
8.REMOVE THROTTLE BODY GASKET
23820
9.REMOVE FUEL VAPOR FEED HOSE ASSEMBLY
Disconnect the fuel vapor hose assembly to the purge valve.
Disengage the clamp to remove the fuel vapor feed hose assembly from the intake manifold.
12262
10.REMOVE NO. 2 VENTILATION HOSE
Slide the hose clip and remove the No. 2 ventilation hose from the cylinder head cover sub-assembly.
25680
11.REMOVE EGR VALVE WITH EGR CCOLER ASSEMBLY
25601
12.REMOVE NO. 1 EGR PIPE SUB-ASSEMBLY
25624
13.REMOVE EGR VALVE ADAPTER
Using an 8 mm socket wrench, remove the bolt and EGR valve adapter from the camshaft housing sub-assembly.
17111
14.REMOVE INTAKE MANIFOLD
17177
15.REMOVE NO. 1 INTAKE MANIFOLD TO HEAD GASKET
23901
16.REMOVE FUEL TUBE SUB-ASSEMBLY
Remove the fuel tube sub-assembly from the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
23902
17.REMOVE NO. 2 FUEL TUBE SUB-ASSEMBLY
Remove the fuel pipe clamp from the fuel tube connector.
Remove the fuel tube sub-assembly from the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PARTS LOCATION
23802B
18.REMOVE NO. 2 FUEL PIPE SUB-ASSEMBLY
Remove the 2 bolts and No. 2 fuel pipe sub-assembly from the camshaft housing subassembly.
23100X
19.REMOVE FUEL PUMP ASSEMBLY (for High Pressure)
20.REMOVE WATER BY-PASS PIPE ASSEMBLY
Remove the bolt.
Slide the clip and remove the water by-pass hose assembly from the water inlet with thermostat sub-assembly.
82219C
21.REMOVE SENSOR WIRE
Disconnect the 4 connectors.
Disengage the 2 clamps.
Remove the bolt and sensor wire from the water inlet with thermostat sub-assembly.
82126A
22.REMOVE NO. 6 ENGINE WIRE
Disconnect the 3 connectors.
Disengage the clamp and remove the No. 6 engine wire from the No. 1 ventilation case.
23250
23.REMOVE FUEL INJECTOR ASSEMBLY
19500
24.REMOVE IGNITION COIL ASSEMBLY
11452D
25.REMOVE OIL LEVEL GAGE GUIDE
Remove the engine oil level dipstick.
Using an 8 mm socket wrench, remove the bolt and engine oil level dipstick guide from the cylinder head sub-assembly.
Remove the O-ring from the engine oil level dipstick guide.
16281
26.REMOVE NO. 4 WATER BY-PASS HOSE
Disengage the clamp to separate the No. 4 water by-pass hose.
Slide the clip and remove the No. 4 water by-pass hose from the water outlet.
27.REMOVE WIRE HARNESS CLAMP BRACKET
Using an 8 mm socket wrench, remove the bolt and wire harness clamp bracket from the camshaft housing sub-assembly.
Using an 8 mm socket wrench, remove the 2 bolts and wire harness clamp bracket from the camshaft housing sub-assembly.
Remove the 2 bolts and wire harness clamp bracket from the camshaft housing sub-assembly.