This procedure includes the installation of small-head bolts. Refer to Small-Head Bolts of Basic Repair Hint to identify the small-head bolts.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
1.INSTALL WIRE HARNESS CLAMP BRACKET
Install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.
Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the 2 bolts.
Using an 8 mm socket wrench, install the wire harness clamp bracket to the camshaft housing sub-assembly with the bolt.
16281
2.INSTALL NO. 4 WATER BY-PASS HOSE
Install the No. 4 water by-pass hose to the water outlet and slide the clip to secure it.
Engage the clamp.
11452D
3.INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
Apply a light coat of engine oil to a new O-ring.
Install the O-ring to the engine oil level dipstick guide.
Using an 8 mm socket wrench, install the engine oil level dipstick guide to the cylinder head sub-assembly with the bolt.
Install the engine oil level dipstick.
19500
4.INSTALL IGNITION COIL ASSEMBLY
23250
5.INSTALL FUEL INJECTOR ASSEMBLY
82126A
6.INSTALL NO. 6 ENGINE WIRE
Engage the clamp.
Connect the 3 connectors.
82219C
7.INSTALL SENSOR WIRE
Install the sensor wire to the water inlet with thermostat sub-assembly with the bolt.
Engage the 2 clamps.
Connect the 4 connectors.
8.INSTALL WATER BY-PASS PIPE ASSEMBLY
Install the water by-pass hose assembly to the water inlet with thermostat sub-assembly and cylinder head sub-assembly and slide the 2 clips to secure them.
Install the bolt.
23100X
9.INSTALL FUEL PUMP ASSEMBLY (for High Pressure)
23802B
10.INSTALL NO. 2 FUEL PIPE SUB-ASSEMBLY
Install the No. 2 fuel pipe sub-assembly to the camshaft housing sub-assembly with the 2 bolts.
23902
11.INSTALL NO. 2 FUEL TUBE SUB-ASSEMBLY
Connect the No. 2 fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
Install the fuel pipe clamp to the fuel tube connector.
23901
12.INSTALL FUEL TUBE SUB-ASSEMBLY
Connect the fuel tube sub-assembly to the No. 2 fuel pipe sub-assembly.
Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION
17177
13.INSTALL NO. 1 INTAKE MANIFOLD TO HEAD GASKET
17111
14.INSTALL INTAKE MANIFOLD
25624
15.INSTALL EGR VALVE ADAPTER
Engage the guide.
Using an 8 mm socket wrench, install the EGR valve adapter with the bolt.
25601
16.INSTALL NO. 1 EGR PIPE SUB-ASSEMBLY
25680
17.INSTALL EGR COOLER ASSEMBLY
12262
18.INSTALL NO. 2 VENTILATION HOSE
Connect the No. 2 ventilation hose to the cylinder head cover sub-assembly and slide the clip to secure it.
23820
19.INSTALL FUEL VAPOR FEED HOSE ASSEMBLY
Engage the clamp.
Install the fuel vapor feed hose assembly to the purge valve.
22271
20.INSTALL THROTTLE BODY GASKET
22030
21.INSTALL THROTTLE BODY WITH MOTOR ASSEMBLY
17141
22.INSTALL EXHAUST MANIFOLD
17118
23.INSTALL MANIFOLD STAY
17167
24.INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR
25733A
25.INSTALL NO. 1 VACUUM PIPE (w/ Differential Pressure Sensor)
89481B
26.INSTALL DIFFERENTIAL PRESSURE SENSOR (w/ Differential Pressure Sensor)
89467B
27.INSTALL AIR FUEL RATIO SENSOR