Home › Vehicle Exterior › EXTERIOR PANELS / TRIM › REAR DOOR BELT MOULDING › from 2020.07
RM36W0E _59 Vehicle Exterior _088302 EXTERIOR PANELS / TRIM _0421043 REAR DOOR BELT MOULDING A

EXTERIOR PANELS / TRIM  REAR DOOR BELT MOULDING  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door belt moulding removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative (-) auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Catch protection function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1:for Gasoline Model

Lane control system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 second or more. (Click here)
Pre-collision system
Stop and start system*1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)

-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
Power door lock control system
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the ignition switch is turned to ON, the servo motor standard position is recognized. -


·

Use the same procedure for the RH side and LH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After the ignition switch is turned off, there may be a waiting time before disconnecting the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL

Hide 67674A 3.REMOVE REAR DOOR FRAME GARNISH

Hide 4.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL (w/ Rear Power Window)

Hide 74272A 5.REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Rear Power Window)

Hide 69260E 6.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Rear Power Window)

Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68174A 8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68197A 9.REMOVE REAR DOOR BELT FRONT SEAL

Hide 68199 10.REMOVE REAR DOOR BELT REAR SEAL

Hide 67842E 11.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 68152C 13.REMOVE REAR DOOR GLASS RUN

Hide 67408E 14.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68104 15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 68230C 16.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

a.
B567975C01
0,0 0,0 false
V100155

Protective Tape


Apply protective tape around the rear door glass outer weatherstrip assembly.


b.
B567976C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the claws to remove the rear door glass outer weatherstrip assembly as shown in the illustration.