Home › Vehicle Exterior › DOOR / HATCH › REAR DOOR › from 2020.07
RM36W0E _59 Vehicle Exterior _088480 DOOR / HATCH _0421654 REAR DOOR A

DOOR / HATCH  REAR DOOR  DISASSEMBLY  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door window regulator sub-assembly

·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the power switch is turned to on (IG), the servo motor standard position is recognized. -


·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 69260E 3.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Rear Power Window)

a.
B347102C02
2.333,1.333 2.073,1.156 false 2.375,1.323 2.688,1.521 0.313,0.198 10 false *a
*a Protective Tape


Insert a clip remover with its shaft wrapped in protective tape between the window regulator handle plate and the rear door window regulator handle assembly.


b.

Turn the rear door window regulator handle assembly with the clip remover inserted, as shown in the illustration.


c.

Remove the shaft snap ring and the rear door window regulator handle assembly.


d.
B346737

Remove the window regulator handle plate.


Hide 67674A 4.REMOVE REAR DOOR FRAME GARNISH

a.
B584285

Disengage the claws and clip to remove the rear door frame garnish.


Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL (w/ Rear Power Window)

a.
B594333

Remove the screw.


b.

Disengage the claws and guides.


c.
B584287

Disconnect the connector to remove the rear power window regulator switch assembly with rear door armrest base upper panel.


Hide 74272A 6.REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Rear Power Window)

a.
B595244

Remove the screw.


b.

Disengage the claws and guides to remove the rear door armrest base upper panel.


Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

a.
B584288C01
1.573,1.76 1.365,1.052 true 1.615,1.667 1.844,1.875 0.229,0.208 10 true *a
*a Protective Tape


Using a screwdriver with its tip wrapped in protective tape, open the rear door inside handle bezel plug.


b.
B584289

Remove the 3 screws.


c.
B584290C01
0,0 0,0 false
V113146

Place Hands Here
V113147

Remove in this Direction


Disengage the clips as shown in the illustration.


d.
B584291C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the rear door trim board sub-assemblywith the rear door glass inner weatherstrip and rear door belt seal as shown in the illustration.


e.
B584292C01
2.5,0.646 2.24,0.927 true 2.438,1.594 2.229,1.271 true 2.531,0.542 2.74,0.708 0.208,0.167 10 true *1 2.479,1.49 2.74,1.677 0.26,0.188 10 true *2
*1 Rear Door Inside Locking Cable Assembly
*2 Rear Door Lock Remote Control Cable Assembly
V113147

Remove in this Direction


Disengage the guides to disconnect the rear door inside locking cable assembly and rear door lock remote control cable assembly to remove the rear door trim board sub-assembly as shown in the illustration.


Hide 69206C 8.REMOVE REAR DOOR INSIDE HANDLE SUB-ASSEMBLY

a.
B584293

Disengage the guides to remove the rear door inside handle sub-assembly.


Hide 69284D 9.REMOVE REAR DOOR INSIDE HANDLE BEZEL PLUG

a.
B584294

Disengage the claw to remove the rear door inside handle bezel plug.


Hide 68174A 10.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

a.
B584295C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door glass inner weatherstrip with the rear door belt seal.


Hide 68197A 11.REMOVE REAR DOOR BELT FRONT SEAL

a.
B584296

Remove the rear door belt front seal from the rear door glass inner weatherstrip.


Hide 68199 12.REMOVE REAR DOOR BELT REAR SEAL

a.
B584297

Disengage the claws to remove the rear door belt rear seal.


Hide 86160B 13.REMOVE REAR SPEAKER ASSEMBLY (w/ Rear Speaker)

Hide 67842E 14.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

a.
B584298

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 67842E 15.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

a.
B584299

Remove the rear door service hole cover.

HINT:

Remove any remaining butyl tape from the rear door panel.



Hide 68152C 16.REMOVE REAR DOOR GLASS RUN

a.
B584300

Remove the rear door glass run.


Hide 67408E 17.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

a.
B584301

Remove the 2 bolts, nut and rear door window division bar sub-assembly.


Hide 68104 18.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

a.

w/ Rear Power Window:

i.

Connect the rear power window regulator switch assembly.


ii.

Connect the cable to the negative (-) auxiliary battery terminal.


iii.

Move the rear door glass sub-assembly so that the door glass bolts can be seen.


iv.

Disconnect the cable from the negative (-) auxiliary battery terminal.


v.

Disconnect the rear power window regulator switch assembly.



b.
B584302

Remove the 2 bolts.


c.
B584303C01
0,0 0,0 false
V113147

Remove in this Direction (1)
V113148

Remove in this Direction (2)


Remove the rear door glass sub-assembly as shown in the illustration.

NOTICE:

Do not damage the front door glass subassembly.



Hide 69840A 19.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/ Rear Power Window)

a.
B584304

Disengage the clamp to separate the wire harness.


b.

Disconnect the connector.


c.

Remove the 6 nuts and rear door window regulator assembly.


Hide 69840A 20.REMOVE REAR DOOR WINDOW REGULATOR ASSEMBLY (w/o Rear Power Window)

a.
B594334

Disengage the clamp to separate the wire harness.


b.

Remove the 6 nuts and rear door window regulator assembly.


Hide 69060A 21.REMOVE REAR DOOR LOCK ASSEMBLY

Hide 69240 22.REMOVE REAR DOOR OUTSIDE HANDLE ASSEMBLY

a.
B584305

Disengage the claws and move the lever as shown in the illustration.


b.
B584306C01
0,0 0,0 false
V113147

Remove in this Direction


Remove the rear door outside handle assembly as shown in the illustration.


Hide 69227L 23.REMOVE REAR DOOR OUTSIDE HANDLE COVER

a.
B584307

Using a T30 "TORX" socket wrench, loosen the screw.


b.

Disengage the claws to remove the rear door outside handle cover.


Hide 69241G 24.REMOVE REAR DOOR OUTSIDE HANDLE FRONT PAD

a.
B584308

Disengage the claws and guide to remove the rear door outside handle front pad.


Hide 69242G 25.REMOVE REAR DOOR OUTSIDE HANDLE REAR PAD

a.
B584309

Disengage the guides to remove the rear door outside handle rear pad.


Hide 69204A 26.REMOVE REAR DOOR OUTSIDE HANDLE FRAME SUB-ASSEMBLY

a.
B584310

Using a T30 "TORX" socket wrench, loosen the screw.


b.
B584311C01
0,0 0,0 false
V113147

Remove in this Direction


Disengage the guides to remove the rear door outside handle frame sub-assembly as shown in the illustration.


Hide 75708 27.REMOVE REAR DOOR WINDOW FRAME MOULDING SUB-ASSEMBLY

Hide 68230C 28.REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY

Hide 68640A 30.REMOVE REAR DOOR CHECK ASSEMBLY

a.
B584312

Remove the 3 bolts and rear door check assembly.


Hide 67872 31.REMOVE REAR DOOR WEATHERSTRIP

a.
B584313C01
2.927,0.208 3.094,0.135 true 3.125,0.042 3.417,0.25 0.292,0.208 10 false *a
*a Clip A


Disengage the clip A and other clips to remove the rear door weatherstrip.


Hide 67837C 32.REMOVE REAR DOOR DUST PROOF SEAL (for TMMF Made)

a.
B584314

Disengage the claws to remove the 3 rear door dust proof seals.


Hide 67837C 33.REMOVE REAR DOOR DUST PROOF SEAL (for TMC Made)

a.

for Type A:

i.
B584314

Disengage the claws to remove the 3 rear door dust proof seals.

NOTICE:

When installing, install 2 dust proof seals in the same way as for type B.




b.

for Type B:

i.
B621544

Disengage the claws to remove the 2 rear door dust proof seals.