Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C050679  Right Front Wheel Speed Sensor Mechanical Linkage Failure  


DESCRIPTION

The skid control ECU (brake actuator assembly) calculates the various wheel speeds based on signals from each type of sensor.

By comparing the calculated wheel speed values with the output values of each wheel speed sensor signal, the skid control ECU (brake actuator assembly) checks that each wheel speed sensor is functioning correctly.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050679 Right Front Wheel Speed Sensor Mechanical Linkage Failure At a vehicle speed of 14 km/h (9 mph) or more, the wheel speed sensor signal output value continuously differs from the control value calculated by the skid control ECU.
·

Front speed sensor LH

·

Speed sensor installation

·

Front speed sensor rotor LH (front axle hub sub-assembly LH)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE

·

After replacing or removing and installing a speed sensor rotor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE



HINT:

The front speed sensor rotor RH is incorporated into the front axle hub sub-assembly RH.

If the front speed sensor rotor RH needs to be replaced, replace the front axle hub sub-assembly RH.


PROCEDURE

1.CHECK DTC
a.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

b.

Check the details of the DTCs.

HINT:

When DTC C050618, C050619, C05061F, C050623 and/or C050624 are output together with DTC C050679, inspect and repair the trouble areas indicated by DTC C050618, C050619, C05061F, C050623 and/or C050624 first.



Result:
Result Proceed to
Only C050679 is output A
C050618, C050619, C05061F, C050623 and/or C050624 are output together B



A

2.PRE-CHECK

B

REPAIR CIRCUITS INDICATED BY OUTPUT DTCS

2.PRE-CHECK
a.

Check that all 4 tires are of correct size, are inflated to the correct pressure, and do not show excessive signs of wear.

HINT:

If a tire is deformed or an incorrectly sized tire or wheel is installed, this DTC may be stored.

Click hereSuspension>TIRE / WHEEL>TIRE AND WHEEL SYSTEM>INSPECTION



Result:
Proceed to
NEXT



NEXT

3.CHECK FREEZE FRAME DATA (FL WHEEL SPEED, FR WHEEL SPEED, RL WHEEL SPEED, RR WHEEL SPEED, VEHICLE SPEED)
3.CHECK FREEZE FRAME DATA (FL WHEEL SPEED, FR WHEEL SPEED, RL WHEEL SPEED, RR WHEEL SPEED, VEHICLE SPEED)

Pre-procedure1

a.

Using the GTS, select a DTC to display the Freeze Frame Data.

HINT:

Using to the freeze frame data, the approximate vehicle conditions that were present when the DTC was stored can be determined.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>FREEZE FRAME DATA



Procedure1

b.

Read the freeze frame data of DTC C050679.

Chassis > Brake
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > DTC(C050679) > Freeze Frame Data
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle Speed
50040 435 13,14,15,16,51 C050679

Post-procedure1

c.

None


Result:
Proceed to
NEXT



NEXT

4.READ VALUE USING GTS (FL WHEEL SPEED, FR WHEEL SPEED, RL WHEEL SPEED, RR WHEEL SPEED, VEHICLE SPEED)
4.READ VALUE USING GTS (FL WHEEL SPEED, FR WHEEL SPEED, RL WHEEL SPEED, RR WHEEL SPEED, VEHICLE SPEED)

Pre-procedure1

a.

Start the engine.


Procedure1

b.

Select the Data List on the GTS.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Vehicle Speed Maximum wheel speed sensor reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FR Wheel Speed
FL Wheel Speed
RR Wheel Speed
RL Wheel Speed
Vehicle Speed
50003 435 13,14,15,16,36

c.

Perform a road test under the same malfunction conditions recreated based on the Freeze Frame Data or customer problem analysis.


d.

Check the value of Wheel Speed and Vehicle Speed.

OK:

The value of each Wheel Speed and Vehicle Speed changes in accordance with vehicle speed and the maximum difference between any 2 sensors is less than 6%.


HINT:

If the result of the road test is within the specified range, it is possible that this DTC was stored due to a particular situation.



Post-procedure1

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

5.CHECK FRONT SPEED SENSOR RH INSTALLATION
5.CHECK FRONT SPEED SENSOR RH INSTALLATION
a.
C168336C53
1.031,0.823 1.25,0.49 false 0.917,1.49 1.24,1.74 false 0.75,1.823 1.073,1.99 0.323,0.167 10 *a 2.427,1.823 2.75,1.99 0.323,0.167 10 *b 0.135,0.135 0.448,0.333 0.313,0.198 10 *1 1.292,0.313 1.625,0.521 0.333,0.208 10 *c 1.292,1.729 1.604,1.927 0.313,0.198 10 *d
*1 Front Speed Sensor RH
*a Correct
*b Incorrect
*c 8.5 N*m (87 kgf*cm, 75 in.*lbf)
*d No clearance


Check the front speed sensor RH installation.

OK:

There is no clearance between the front speed sensor LH and front steering knuckle LH.

The installation bolt is tightened properly.



Torque:
8.5 N*m (87 kgf*cm, 75 in.*lbf)

Result:
Proceed to
OK
NG



OK

6.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

NG

REINSTALL OR REPLACE FRONT SPEED SENSOR RH

6.CHECK FRONT SPEED SENSOR RH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Procedure1

b.

Check the front speed sensor RH.

OK:

The front speed sensor RH tip is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor RH, clean the front speed sensor RH.

·

If the front speed sensor RH is damaged, replace the front speed sensor RH with a new one.




Post-procedure1

c.

None


Result:
Result Proceed to
OK A
NG (The front speed sensor RH is damaged.) B
NG (There is foreign matter on the front speed sensor RH.) C



A

7.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

B

C

CLEAN FRONT SPEED SENSOR RH

7.CHECK FRONT SPEED SENSOR ROTOR RH (CHECK FOR FOREIGN MATTER)

Pre-procedure1

a.

Remove the component with the front speed sensor rotor RH.

Click hereDrivetrain>AXLE AND DIFFERENTIAL>FRONT AXLE HUB (for TMMF Made)>REMOVAL


Procedure1

b.

Check the front speed sensor rotor RH.

OK:

The front speed sensor rotor RH is free of scratches, oil, and foreign matter.


NOTICE:
·

If there is oil or foreign matter on the front speed sensor rotor RH, clean the front speed sensor rotor RH.

·

Do not use parts cleaner when cleaning the front speed sensor rotor RH.

·

If the front speed sensor rotor RH is damaged, replace the front axle hub sub-assembly RH with a new one.




Post-procedure1

c.

None


Result:
Result Proceed to
OK A
NG (The front speed sensor rotor RH is damaged.) B
NG (There is foreign matter on the front speed sensor rotor RH.) C



A

B

REPLACE FRONT AXLE HUB SUB-ASSEMBLY RH

C

CLEAN FRONT SPEED SENSOR ROTOR RH