Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C052C12  ABS Pump Motor Control Circuit Short to Battery  C052C14  ABS Pump Motor Control Circuit Short to Ground or Open  


DESCRIPTION

The motor relay and motor fail safe relay are built into the brake actuator assembly.

When the skid control ECU (brake actuator assembly) operates ABS, TRC, VSC, brake assist, etc., the motor relay turns ON and drives the motor pump built into the brake actuator assembly.

If any DTCs related to motor supply power are stored, fail-safe is performed and supply of power to the motor relay is cut by the motor fail safe relay.

When an abnormality in the ABS pump motor drive circuit voltage is detected, the following DTCs are stored.

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C052C12 ABS Pump Motor Control Circuit Short to Battery
·

When the pump motor is stopped, the pump motor drive circuit voltage is more than 0.93 V for approximately 10 seconds or more.

·

When the pump motor is started, the pump motor drive circuit voltage is more than 0.93 V for approximately 12 seconds or more.


·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake
C052C14 ABS Pump Motor Control Circuit Short to Ground or Open When the pump motor is operating, the pump motor drive circuit voltage is less than 7.3 V for approximately 1.8 seconds or more.
·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

WIRING DIAGRAM

C322755E21
0.313,1.333 1.167,2.01 0.854,0.677 10 false from Auxiliary Battery 1.781,1.542 2.688,1.792 0.906,0.25 10 false ABS NO. 1 4.76,2.208 6.302,2.458 1.542,0.25 10 false Skid Control ECU 4.646,1.281 6.573,1.604 1.927,0.323 10 false Motor Fail Safe Relay 4.979,3.302 5.896,3.542 0.917,0.24 10 false Motor Relay 5.094,4.438 6.01,4.677 0.917,0.24 10 false Pump Motor 4.49,5.031 6.438,5.354 1.948,0.323 10 false Brake Actuator Assembly 4.49,4.865 4.875,5.073 0.385,0.208 10 false A37 3.667,2.854 4.229,3.073 0.563,0.219 10 false GND2 3.677,1.25 4.24,1.469 0.563,0.219 10 false +BM 3.458,1.25 3.688,1.469 0.229,0.219 10 false 1 3.406,2.875 3.635,3.094 0.229,0.219 10 false 13

CAUTION / NOTICE / HINT

NOTICE:
·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (+BM TERMINAL)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A37-1 (+BM) - Body ground Always 11 to 14 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (GND2 TERMINAL)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A37-13 (GND2) - Body ground 1 minute or more after disconnecting the cable from the negative (-) auxiliary battery terminal Below 1 Ω



Result:
Proceed to
OK
NG



OK

3.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CLEAR DTC

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


Procedure1

b.

Operate the GTS to clear the codes.

Chassis > Brake > Clear DTCs
50002 435

Post-procedure1

c.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

4.RECONFIRM DTC
4.RECONFIRM DTC

Pre-procedure1

a.

Based on the Freeze Frame Data and interview with the customer, attempt to reproduce the conditions when the malfunction occurred.


Procedure1

b.

Operate the GTS to read the DTCs.

Chassis > Brake > Trouble Codes
50001 435

c.

Check if the same DTC is output.


Post-procedure1

d.

Turn the ignition switch off.


Result:
Result Proceed to
C052C12 and C052C14 are not output A
C052C12 or C052C14 is output B


HINT:
·

If a speed signal of 20 km/h (12 mph) or more is sent to the skid control ECU (brake actuator assembly) with the ignition switch turned to ON and the stop light switch assembly off, the ECU performs self-diagnosis of the motor circuit.

·

If the normal system code is output (no DTCs are output), slightly jiggle the connectors, wire harness, and fuses of the skid control ECU (brake actuator assembly).

·

If any DTCs are output while jiggling a connector or wire harness of the skid control ECU (brake actuator assembly), inspect and repair the connector or wire harness.

·

If no DTCs were output when reconfirming DTCs, checking for intermittent problems is necessary because it is suspected that the original DTCs were stored due to the poor connection of a connector terminal.




A

B