Home › Brake › PARKING BRAKE › ELECTRIC PARKING BRAKE SYSTEM › 2020.07–2021.11
RM36W0E _54 Brake _089430 PARKING BRAKE _0433905 ELECTRIC PARKING BRAKE SYSTEM C

PARKING BRAKE  ELECTRIC PARKING BRAKE SYSTEM  C060962  Electric Parking Brake Switch Signal Compare Failure  


DESCRIPTION

When the electric parking brake switch is pulled, a lock request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly. When the electric parking brake switch is pushed, a release request signal is sent from the skid control ECU (brake actuator assembly) to the parking brake actuator assembly.

DTC No. Detection Item DTC Detection Condition Trouble Area Memory Note
C060962 Electric Parking Brake Switch Signal Compare Failure
·

Open or short detected in parking brake switch circuit for 1 second or more

·

Stuck parking brake switch detected (when parked: 30 seconds, when driving: 1 second, during engine stall: 1 second)

·

Stuck parking brake switch detected 3 times in succession when being operated


·

Electric parking brake switch (electric parking brake switch assembly)

·

Wire harness or connector

·

Skid control ECU (brake actuator assembly)


DTC stored An electric parking brake system malfunction is displayed on the multi-information display.

DTC Detection Conditions: C060962
Vehicle Condition
Pattern 1 Pattern 2 Pattern 3 Pattern 4 Pattern 5 Pattern 6
Diagnosis Condition Vehicle is stopped - - ○ - - -
Vehicle is being driven - - - ○ - -
During initial check - - - - ○ -
Parking brake switch is being operated - - - - - ○
Malfunction Status Open detected in parking brake switch circuit ○ - - - - -
Short detected in parking brake switch circuit - ○ - - - -
Stuck parking brake switch detected - - ○ ○ ○ ○
Detection Time 1 second or more 1 second or more 30 seconds or more 1 second or more 1 second or more -
Number of Trips 1 trip 1 trip 1 trip 1 trip 1 trip 3 trip

HINT:

DTC will be output when conditions for either of the patterns in the table above are met.


WIRING DIAGRAM

C367775E73
1.365,3.156 3.771,3.604 2.406,0.448 10 false Electric Parking Brake Switch (Electric Parking Brake Switch Assembly) 5.156,3.688 6.729,4.219 1.573,0.531 10 false Skid Control ECU (Brake Actuator Assembly) 5.167,3.49 5.604,3.677 0.438,0.188 10 false A39 1.365,2.979 1.802,3.167 0.438,0.188 10 false H48 3.333,1.25 3.771,1.438 0.438,0.188 10 false SWI1 3.26,1.563 3.792,1.75 0.531,0.188 10 false SWO1 3.323,1.865 3.76,2.052 0.438,0.188 10 false SWI2 3.25,2.427 3.781,2.615 0.531,0.188 10 false SWO2 5.469,1.365 5.906,1.552 0.438,0.188 10 false SWI1 5.458,1.646 5.938,1.833 0.479,0.188 10 false SWO1 5.458,1.969 5.896,2.156 0.438,0.188 10 false SWI2 5.469,2.563 5.979,2.75 0.51,0.188 10 false SWO2 3.792,1.25 3.979,1.448 0.188,0.198 10 false 7 3.792,1.552 4.052,1.75 0.26,0.198 10 false 8 5.198,1.563 5.385,1.76 0.188,0.198 10 false 32 3.802,1.844 3.99,2.042 0.188,0.198 10 false 1 3.802,2.438 3.99,2.635 0.188,0.198 10 false 2 5.208,1.26 5.396,1.458 0.188,0.198 10 false 31 5.198,1.865 5.385,2.063 0.188,0.198 10 false 15 5.188,2.448 5.375,2.646 0.188,0.198 10 false 16

CAUTION / NOTICE / HINT

NOTICE:
·

If the electric parking brake switch is held near the lock position but not fully in the lock position for 1 second or more, a DTC may be stored due to one of the two contacts being ON while the other is OFF. (This is not a system malfunction.)

·

To ensure that the electric parking brake does not operate, wait for 3 minutes or more with the ignition switch off, the driver door closed, and the brake pedal not depressed, then disconnect each connector, fuse and relay.

·

After replacing the skid control ECU (brake actuator assembly), perform calibration (brake pedal stroke sensor assembly zero point calibration, system information memorization, and yaw rate and acceleration sensor zero point calibration) after performing "Reset Memory".

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made)>UTILITY

·

When replacing the skid control ECU (brake actuator assembly), operate the electric parking brake switch (electric parking brake switch assembly) as the parking brake indicator light (red) blinks when the ignition switch is first turned ON.



PROCEDURE

1.READ VALUE USING GTS (EPB SWITCH)
a.

Operate the electric parking brake switch assembly and check that the value of "EPB Switch" in the Data List changes between Lock and Release in accordance with the operation of the switch.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EPB Switch Electric parking brake switch assembly input OFF / Lock / Release / Unknown OFF: Lock switch and release switch are off
Lock: Lock switch on
Release: Release switch on
When not normal, electric parking brake switch assembly release side system may be malfunctioning
HINT:

EPB stands for electric parking brake.


Chassis > Brake > Data List
Tester Display
EPB Switch
50003 435 142
OK:

The value of EPB Switch changes between Lock and Release in accordance with switch operation.


Result:
Proceed to
OK
NG




OK

2.CLEAR DTC

NG

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)
2.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435
Result:
Proceed to
NEXT




NEXT

3.CHECK DTC
3.CHECK DTC
a.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B

4.INSPECT ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

OK

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))

NG

REPLACE ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY)

5.CHECK HARNESS AND CONNECTOR (BRAKE ACTUATOR ASSEMBLY - ELECTRIC PARKING BRAKE SWITCH (ELECTRIC PARKING BRAKE SWITCH ASSEMBLY))
a.

Disconnect the H48 electric parking brake switch (electric parking brake switch assembly) connector.


b.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A39-31 (SWI1) - H48-7 (SWI1) Always Below 1 Ω
A39-32 (SWO1) - H48-8 (SWO1) Always Below 1 Ω
A39-15 (SWI2) - H48-1 (SWI2) Always Below 1 Ω
A39-16 (SWO2) - H48-2 (SWO2) Always Below 1 Ω
A39-31 (SWI1) or H48-7 (SWI1) - Body ground Always 10 kΩ or higher
A39-32 (SWO1) or H48-8 (SWO1) - Body ground Always 10 kΩ or higher
A39-15 (SWI2) or H48-1 (SWI2) - Body ground Always 10 kΩ or higher
A39-16 (SWO2) or H48-2 (SWO2) - Body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

6.CLEAR DTC

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CLEAR DTC
a.

Clear the DTCs.

Chassis > Brake > Clear DTCs
50002 435

b.

Turn the ignition switch off.


Result:
Proceed to
NEXT



NEXT

7.CHECK DTC
7.CHECK DTC
a.

Check for DTCs.

Chassis > Brake > Trouble Codes
50001 435

Result:
Result Proceed to
DTCs are output A
DTCs are not output B



A

B