Home › Engine / Hybrid System › M15A-FKS (FUEL) › FUEL TANK › from 2020.07
RM36W0E _51 Engine / Hybrid System _088660 M15A-FKS FUEL _0422106 FUEL TANK A

M15A-FKS FUEL  FUEL TANK  INSTALLATION  


PROCEDURE

Hide 77277R 1.INSTALL FUEL TANK FILLER PIPE PROTECTOR

a.

Engage the 4 clamps to install a new fuel tank filler pipe protector to the fuel tank filler pipe sub-assembly.


b.

Engage the 4 claws.


Hide 77218A 2.INSTALL NO. 3 FUEL TANK FILLER PIPE SUPPORT

a.

Engage the 3 clamps to install the No. 3 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.


Hide 77216A 3.INSTALL NO. 1 FUEL TANK FILLER PIPE SUPPORT

a.

Engage the 3 clamps to install the No. 1 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.


Hide 77217A 4.INSTALL NO. 2 FUEL TANK FILLER PIPE SUPPORT

a.

Engage the 2 claws to install the No. 2 fuel tank filler pipe support to the fuel tank filler pipe sub-assembly.


Hide 77027B 5.INSTALL NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Engage the clamp to install the No. 1 fuel emission tube sub-assembly to the fuel tank assembly.


Hide 77209F 6.INSTALL FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Engage the clamp to install the fuel tank main tube sub-assembly to the fuel tank assembly.


Hide 77100U 7.INSTALL FUEL TANK ASSEMBLY

CAUTION:
A344817

The fuel tank assembly is very heavy. Be sure to follow the procedure described in the repair manual, or the fuel tank assembly may fall off the engine lifter.


a.

Set the fuel tank assembly on an engine lifter.

NOTICE:

Using height adjustment attachments and plate lift attachments, keep the fuel tank assembly horizontal.



b.

Using the engine lifter, slowly raise the fuel tank assembly, and then temporarily install the fuel tank assembly with the 4 bolts.


c.
A465241N01
2.167,0.292 2.323,0.49 0.156,0.198 10 true 2 2.813,1.948 2.969,2.146 0.156,0.198 10 true 4 1.115,0.281 1.292,0.469 0.177,0.188 10 true 3 0.438,1.938 0.604,2.125 0.167,0.188 10 true 1

Tighten the 4 bolts in the order shown in the illustration.

Torque:
45 N*m (459 kgf*cm, 33 ft.*lbf)

NOTICE:
·

Be careful not to drop the fuel tank assembly.

·

When installing the fuel tank assembly, tilt it slightly to prevent it from interfering with the surrounding parts.




d.

Connect the fuel tank breather tube to the fuel tank filler pipe sub-assembly.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 8.INSTALL FUEL TANK FILLER PIPE SUB-ASSEMBLY

a.

Engage the locations shown in the illustration, and engage the fuel tank filler pipe sub-assembly to the vehicle body.

A465233


b.

Install the bolt.


Hide 77209F 9.CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

a.

Connect the fuel tank main tube sub-assembly to the fuel pipe.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77027B 10.CONNECT NO. 1 FUEL EMISSION TUBE SUB-ASSEMBLY

a.

Connect the No. 1 fuel emission tube sub-assembly to the fuel pipe and slide the clip to secure it.

Click hereEngine / Hybrid System>M15A-FKS (FUEL)>FUEL SYSTEM>PRECAUTION


Hide 77606 11.INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

a.

Install the No. 1 fuel tank protector sub-assembly to the fuel tank assembly with the 3 clips.


Hide 17410 12.INSTALL FRONT EXHAUST PIPE ASSEMBLY

Hide 51447D 13.INSTALL NO. 4 CENTER ENGINE UNDER COVER (for TMC Made)

Hide 51447D 14.INSTALL NO. 4 CENTER ENGINE UNDER COVER (for TMMF Made)

Hide 77310A 15.INSTALL FUEL TANK CAP ASSEMBLY

Hide 77020A 16.INSTALL FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY

Hide 65638 17.INSTALL REAR WHEEL HOUSE LINER LH

a.

Install the rear fender liner with the grommet and 5 clips.


b.

Install the 2 screws.


Hide 18.INSTALL WHEEL ASSEMBLY

Hide 19.ADD FUEL