Home › Vehicle Interior › DOOR LOCK › REAR DOOR LOCK › from 2020.07
RM36W0E _58 Vehicle Interior _088479 DOOR LOCK _0421643 REAR DOOR LOCK A

DOOR LOCK  REAR DOOR LOCK  REMOVAL  


CAUTION / NOTICE / HINT

The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during the rear door lock assembly removal/installation are shown below.

Necessary Procedure After Parts Removed/Installed/Replaced
Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link
Disconnect cable from negative auxiliary battery terminal Memorize steering angle neutral point Parking assist monitor system (Click here)
·

Door glass

·

Door glass run


Initialize power window control system
·

Auto up and down function

·

Jam protection function

·

Catch protection function

·

Remote control function

·

Key-linked function

·

Wireless transmitter-linked function

·

Key-off operation function

·

Window open warning function


(Click here)

HINT:
·

When the cable is disconnected/reconnected to the auxiliary battery terminal, systems temporarily stop operating. However, each system has a function that completes learning the first time the system is used.

-

Learning completes when vehicle is driven

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link

*1: for Gasoline Model

Lane tracing assist system Drive the vehicle straight ahead at 35 km/h (22 mph) or more for 5 seconds or more. (Click here)
Pre-collision system
Stop and start system *1 Drive the vehicle until stop and start control is permitted (approximately 5 to 60 minutes) (Click here)


-

Learning completes when vehicle is operated normally

Effect/Inoperative Function When Necessary Procedures are not Performed Necessary Procedures Link
·

Back door opener


Perform door unlock operation with door control switch or electrical key transmitter sub-assembly switch. (Click here)
Air conditioning system After the power switch is turned to on (IG), the servo motor standard position is recognized. -


·

Use the same procedure for the LH side and RH side.

·

The following procedure is for the LH side.



PROCEDURE

Hide 1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) auxiliary battery terminal.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>BEFORE DISCONNECTING BATTERY


Hide 2.DISCONNECT CABLE FROM NEGATIVE AUXILIARY BATTERY TERMINAL


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.



Hide 69260E 3.REMOVE REAR DOOR WINDOW REGULATOR HANDLE ASSEMBLY (w/o Power Window)

Hide 67674A 4.REMOVE REAR DOOR FRAME GARNISH

Hide 5.REMOVE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY WITH REAR DOOR ARMREST BASE UPPER PANEL (w/ Power Window)

Hide 74272A 6.REMOVE REAR DOOR ARMREST BASE UPPER PANEL (w/o Power Window)

Hide 67604 7.REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY

Hide 68174A 8.REMOVE REAR DOOR GLASS INNER WEATHERSTRIP

Hide 68197A 9.REMOVE REAR DOOR BELT FRONT SEAL

Hide 68199 10.REMOVE REAR DOOR BELT REAR SEAL

Hide 67842E 11.REMOVE REAR DOOR SERVICE HOLE COVER (w/ Rear Speaker)

Hide 67842E 12.REMOVE REAR DOOR SERVICE HOLE COVER (w/o Rear Speaker)

Hide 68152C 13.REMOVE REAR DOOR GLASS RUN

Hide 67408E 14.REMOVE REAR DOOR WINDOW DIVISION BAR SUB-ASSEMBLY

Hide 68104 15.REMOVE REAR DOOR GLASS SUB-ASSEMBLY

Hide 69060A 16.REMOVE REAR DOOR LOCK ASSEMBLY

a.
B584485

Disconnect the connector.


b.

Using a T30 "TORX" socket wrench, remove the 3 screws and rear door lock assembly.


c.
B584486

Move the rear door lock assembly downward as shown in the illustration to disconnect it from the release plate of the rear door outside handle frame sub-assembly, and remove the rear door lock assembly.


d.

When reusing the rear door lock assembly:

i.
B584487

Remove the door lock wiring harness seal from the rear door lock assembly.



Hide 69740E 17.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/o Double Locking System)

a.
B584488C01
1.24,0.667 0.906,1.063 true 1.229,0.479 1.438,0.667 0.208,0.188 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B584489

Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock assembly.


Hide 69740E 18.REMOVE REAR DOOR LOCK REMOTE CONTROL CABLE ASSEMBLY (w/ Double Locking System)

a.
B584492C01
2.594,1.448 1.719,1.281 true 2.656,1.344 2.969,1.542 0.313,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B584493

Disengage the guide to remove the rear door lock remote control cable assembly from the rear door lock assembly.


Hide 69780E 19.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/o Double Locking System)

a.
B584490C01
1.802,1.01 2.26,0.688 true 2.24,0.51 2.49,0.708 0.25,0.198 10 true *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B584491

Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock assembly.


Hide 69780E 20.REMOVE REAR DOOR INSIDE LOCKING CABLE ASSEMBLY (w/ Double Locking System)

a.
B584494C01
2.656,1.656 2.25,1.229 true 2.719,1.583 3.031,1.781 0.313,0.198 10 false *a
*a Protective Tape
V113147

Remove in this Direction


Using a screwdriver with its tip wrapped in protective tape, disengage the claws as shown in the illustration.


b.
B584495

Disengage the guide to remove the rear door inside locking cable assembly from the rear door lock assembly.