This DTC is output when the clearance warning ECU assembly detects lost communication with the blind spot monitor sensor.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| U117787 | Lost Communication with Side Obstacle Detection Control Module "A" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor RH (A) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 9 global CAN junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor RH (A) ·
Power source circuit of blind spot monitor sensor RH (A) ·
Blind spot monitor sensor RH (A) ground circuit ·
Blind spot monitor sensor LH (B) |
| U117887 | Lost Communication with Side Obstacle Detection Control Module "B" (ch2) Missing Message | The clearance warning ECU assembly is unable to receive communication from the blind spot monitor sensor LH (B) | ·
Open or short in CAN bus main wire or connector ·
Open or short in CAN bus wire or connector ·
Open or short in No. 9 global CAN junction connector ·
Clearance warning ECU assembly ·
Blind spot monitor sensor LH (B) ·
Power source circuit of blind spot monitor sensor LH (B) ·
Blind spot monitor sensor LH (B) ground circuit ·
Blind spot monitor sensor RH (A) |
Inspect the fuses for circuits related to this system before performing the following procedure.
Before measuring the resistance of the CAN bus, turn the ignition switch off and leave the vehicle for 1 minute or more without operating the key or any switches, or opening or closing the doors. After that, disconnect the cable from the negative (-) battery terminal and leave the vehicle for 1 minute or more before measuring the resistance.
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Operating the ignition switch, any other switches or a door triggers related ECU and sensor communication on the CAN. This communication will cause the resistance value to change.
Even after DTCs are cleared, if a DTC is stored again after driving the vehicle for a while, the malfunction may be occurring due to vibration of the vehicle. In such a case, wiggling the ECUs or wire harness while performing the inspection below may help determine the cause of the malfunction.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC U117787 only is output | A |
| DTC U117887 only is output | B |
| DTC U117787 and U117887 are output | C |
A
B
C
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Disconnect the S6 blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-10 (BRGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| S6-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V |
| S6-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O37 blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-10 (BRGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O37-5 (BRB) - Body ground | Ignition switch ON | 11 to 14 V |
| O37-5 (BRB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Disconnect the T6 blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-10 (BLGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| T6-5 (BLB) - Body ground | Ignition switch ON | 11 to 14 V |
| T6-5 (BLB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the O38 blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O38-10 (BLGD) - Body ground | Always | Below 1 Ω |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| O38-5 (BLB) - Body ground | Ignition switch ON | 11 to 14 V |
| O38-5 (BLB) - Body ground | Ignition switch off | Below 1 V |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(No. 9 Global CAN Junction Connector) |
| *b | Front view of DLC3 |
Turn the ignition switch off.
Disconnect the cable from the negative (-) auxiliary battery terminal.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition | Result |
|---|---|---|---|
| O87-9 (CANH) - O87-20 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω | Below 54 Ω: Short circuit between bus lines |
| 70 Ω or more: Open circuit in main bus lines | |||
| O87-9 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANH short to ground |
| O87-20 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher | Below 200 Ω: CANL short to ground |
| O87-9 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANH +B short |
| O87-20 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher | Below 6 kΩ: CANL +B short |
| Result | Proceed to |
|---|---|
| OK | A |
| Open circuit in CAN main bus lines | B |
| Short circuit between bus lines | C |
·
Short to ground ·
+B short |
D |
A
B
C
D
Reconnect the cable to the negative (-) auxiliary battery terminal.
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click hereGeneral>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION
Clear the DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR
Check for DTCs.
Click hereAudio / Visual / Telematics>PARK ASSIST / MONITORING>PARKING SUPPORT BRAKE SYSTEM>DTC CHECK / CLEAR
| Result | Proceed to |
|---|---|
| DTC U117787 and U117887 are not output | A |
| DTC U117787 and U117887 are output | B |
A
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
B
Disconnect the No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O87-9 (CANH) - O87-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-10 (CANH) - O87-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| O87-11 (CANH) - O87-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-1 (CA2P) - T6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-1 (CA2P) - S6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O60-37 (CANH) - O60-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O38-1 (CA2P) - O38-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-1 (CA2P) - O37-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O87-9 (CANH) - O87-20 (CANL) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-10 (CANH) - O87-21 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| O87-11 (CANH) - O87-22 (CANL) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-1 (CA2P) - T6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-1 (CA2P) - S6-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O60-37 (CANH) - O60-38 (CANL) | Cable disconnected from negative (-) battery terminal | 54 to 69 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O38-1 (CA2P) - O38-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-1 (CA2P) - O37-6 (CA2N) | Cable disconnected from negative (-) battery terminal | 108 to 132 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the No. 9 global CAN junction connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O87-9 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-20 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-9 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O87-20 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O87-10 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-21 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-10 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O87-21 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O87-11 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-22 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O87-11 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O87-22 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
Check for short that was confirmed to be a malfunction by confirming symptoms.
| Result | Proceed to |
|---|---|
| OK | A |
| NG (to blind spot monitor sensor LH (B) CAN main wire) | B |
| NG (to blind spot monitor sensor RH (A) CAN main wire) | C |
| NG (to clearance warning ECU assembly CAN wire) | D |
A
B
C
D
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| T6-1 (CA2P) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T6-6 (CA2N) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| T6-1 (CA2P) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| T6-6 (CA2N) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check the vehicle specifications.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made | B |
A
B
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| S6-1 (CA2P) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S6-6 (CA2N) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| S6-1 (CA2P) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| S6-6 (CA2N) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the clearance warning ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O60-37 (CANH) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O60-38 (CANL) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O60-37 (CANH) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O60-38 (CANL) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor LH (B) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O38-1 (CA2P) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O38-6 (CA2N) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O38-1 (CA2P) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O38-6 (CA2N) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Reconnect the O87 No. 9 global CAN junction connector.
Disconnect the blind spot monitor sensor RH (A) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| O37-1 (CA2P) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O37-6 (CA2N) - H3-4 (CG) | Cable disconnected from negative (-) battery terminal | 200 Ω or higher |
| O37-1 (CA2P) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| O37-6 (CA2N) - H3-16 (BAT) | Cable disconnected from negative (-) battery terminal | 6 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG