Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function, HV Model) › 2020.07–2021.11
RM36W0E _58 Vehicle Interior _087476 THEFT DETERRENT / KEYLESS ENTRY _0424992 ENTRY AND START SYSTEM(for Start Function, HV Model) J

THEFT DETERRENT / KEYLESS ENTRY  ENTRY AND START SYSTEM(for Start Function, HV Model)  Power Source Mode does not Change to ON (READY)  


DESCRIPTION

When the electrical key transmitter sub-assembly is in the cabin and the power switch is pressed, the certification ECU (smart key ECU assembly) receives a signal and changes the power source mode. Additionally, when the shift lever is in P and the brake pedal is depressed, the hybrid control system can be started by pressing the power switch. If the steering is unlocked, the hybrid control system can also be started by pressing the power switch with the shift lever in P and the brake pedal depressed.

Related Data List and Active Test Items
Problem Symptom Data List and Active Test
Power source mode does not change to ON (READY)
Power Source Control
·

Stop Light Switch

·

Steering Unlock Switch

·

Shift P Signal

·

Power Supply Condition


Entry&Start
·

Immobiliser

·

Start Request

·

S Code Check

·

L Code Check



WIRING DIAGRAM

for TMC Made


E446751E01
0.167,0.354 1.052,0.885 0.885,0.531 10 false from Auxiliary Battery 1.646,0.552 2.219,0.844 0.573,0.292 10 false STOP 2.24,0.271 2.625,0.531 0.385,0.26 10 false 7 2.229,0.688 2.615,0.948 0.385,0.26 10 false 2 2.427,0.385 2.813,0.646 0.385,0.26 10 false B 2.865,0.615 3.125,0.854 0.26,0.24 10 false IC 3.208,0.385 3.594,0.646 0.385,0.26 10 false L 3.396,0.385 3.781,0.646 0.385,0.26 10 false 3 1.927,2.823 2.313,3.083 0.385,0.26 10 false H20 1.927,3 4.052,3.385 2.125,0.385 10 false Shift Lock Control Unit Assembly 3.115,1.948 3.5,2.208 0.385,0.26 10 false P2 3.385,1.958 3.771,2.219 0.385,0.26 10 false 3 4.938,2.073 5.323,2.333 0.385,0.26 10 false H46 4.969,1.875 5.354,2.135 0.385,0.26 10 false 14 2.167,1.24 3.063,1.469 0.896,0.229 10 false A63 2.146,1.406 4.031,1.698 1.885,0.292 10 false Stop Light Switch Assembly 5.219,4.563 6.74,5.01 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.073,5.125 1.917,5.521 1.844,0.396 10 false Hybrid Vehicle Control ECU 5.521,3.021 6.094,3.313 0.573,0.292 10 false +B 0.927,4.073 1.5,4.365 0.573,0.292 10 false STP 0.938,3.333 1.51,3.625 0.573,0.292 10 false ST2 4.979,0.292 5.365,0.552 0.385,0.26 10 false 21 4.948,0.49 5.333,0.75 0.385,0.26 10 false H45 5.01,3.26 5.396,3.521 0.385,0.26 10 false 2 1.323,4.094 1.708,4.354 0.385,0.26 10 false A68 1.323,3.458 1.708,3.719 0.385,0.26 10 false H44 1.406,3.26 1.792,3.521 0.385,0.26 10 false 4 1.406,3.885 1.792,4.146 0.385,0.26 10 false 6 5.323,1.99 5.708,2.25 0.385,0.26 10 false P 6.26,2.094 6.521,2.333 0.26,0.24 10 false IC 6.25,3.604 6.51,3.844 0.26,0.24 10 false IC 4.938,3.448 5.323,3.708 0.385,0.26 10 false H45 2.427,0.802 2.813,1.063 0.385,0.26 10 false GND 5.417,5.438 5.99,5.729 0.573,0.292 10 false STP2 5.323,0.396 5.896,0.688 0.573,0.292 10 false STP1 5.313,3.354 5.885,3.646 0.573,0.292 10 false ST2 5.708,1.583 6.281,1.875 0.573,0.292 10 false +B 6.25,0.625 6.51,0.865 0.26,0.24 10 false IC 5.188,5.354 5.76,5.646 0.573,0.292 10 false 37 4.75,5.875 7.104,6.344 2.354,0.469 10 false Skid Control ECU (Brake Booster with Master Cylinder Assembly) 4.76,5.719 5.99,5.979 1.229,0.26 10 false A38


for TMMF Made


E446729E04
0.167,0.354 1.052,0.885 0.885,0.531 10 false from Auxiliary Battery 1.646,0.552 2.219,0.844 0.573,0.292 10 false STOP 2.24,0.271 2.625,0.531 0.385,0.26 10 false 7 2.229,0.688 2.615,0.948 0.385,0.26 10 false 2 2.427,0.385 2.813,0.646 0.385,0.26 10 false B 2.865,0.615 3.125,0.854 0.26,0.24 10 false IC 3.208,0.385 3.594,0.646 0.385,0.26 10 false L 3.396,0.385 3.781,0.646 0.385,0.26 10 false 3 1.948,2.552 2.333,2.813 0.385,0.26 10 false H20 1.938,2.74 4.063,3.125 2.125,0.385 10 false Shift Lock Control Unit Assembly 3.115,1.948 3.5,2.208 0.385,0.26 10 false P2 3.385,1.958 3.771,2.219 0.385,0.26 10 false 3 4.938,2.073 5.323,2.333 0.385,0.26 10 false H46 4.969,1.875 5.354,2.135 0.385,0.26 10 false 14 2.167,1.24 3.063,1.469 0.896,0.229 10 false A63 2.146,1.406 4.031,1.698 1.885,0.292 10 false Stop Light Switch Assembly 5.073,5.698 6.302,5.958 1.229,0.26 10 false A39 5.219,4.563 6.74,5.01 1.521,0.448 10 false Certification ECU (Smart Key ECU Assembly) 0.073,5.125 1.917,5.521 1.844,0.396 10 false Hybrid Vehicle Control ECU 5.521,3.021 6.094,3.313 0.573,0.292 10 false +B 0.927,4.073 1.5,4.365 0.573,0.292 10 false STP 0.938,3.333 1.51,3.625 0.573,0.292 10 false ST2 4.979,0.292 5.365,0.552 0.385,0.26 10 false 21 4.948,0.49 5.333,0.75 0.385,0.26 10 false H45 5.01,3.26 5.396,3.521 0.385,0.26 10 false 2 1.323,4.094 1.708,4.354 0.385,0.26 10 false A68 1.323,3.458 1.708,3.719 0.385,0.26 10 false H44 1.406,3.26 1.792,3.521 0.385,0.26 10 false 4 1.406,3.885 1.792,4.146 0.385,0.26 10 false 6 5.323,1.99 5.708,2.25 0.385,0.26 10 false P 6.26,2.094 6.521,2.333 0.26,0.24 10 false IC 6.25,3.604 6.51,3.844 0.26,0.24 10 false IC 4.938,3.448 5.323,3.708 0.385,0.26 10 false H45 2.427,0.802 2.813,1.063 0.385,0.26 10 false GND 5.417,5.438 5.99,5.729 0.573,0.292 10 false STP2 5.323,0.396 5.896,0.688 0.573,0.292 10 false STP1 5.313,3.354 5.885,3.646 0.573,0.292 10 false ST2 5.156,5.344 5.729,5.635 0.573,0.292 10 false 43 5.708,1.583 6.281,1.875 0.573,0.292 10 false +B 6.25,0.625 6.51,0.865 0.26,0.24 10 false IC 5.073,5.875 6.604,6.26 1.531,0.385 10 false Skid Control ECU (Brake Actuator Assembly) 3,5.469 3.385,5.729 0.385,0.26 10 false STP 3.396,5.344 3.781,5.604 0.385,0.26 10 false 21 2.104,5.823 3.135,6.104 1.031,0.281 10 false A34*1, A35*2 2.104,5.99 4.229,6.198 2.125,0.208 10 false Brake Booster Control Computer 0.854,6.396 1.802,6.656 0.948,0.26 10 false *1: for LHD 1.875,6.406 2.823,6.667 0.948,0.26 10 false *2: for RHD


CAUTION / NOTICE / HINT

NOTICE:
·

When using the GTS with the ignition switch off, connect the GTS to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the GTS and the vehicle begins. Then select Model Code "KEY REGIST" under manual mode and enter the following menus: Body Electrical / Entry&Start(CAN). While using the GTS, periodically turn a courtesy light switch on and off at intervals of 1.5 seconds or less to maintain communication between the GTS and the vehicle.

·

The entry and start system (for Start Function) uses the LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>HOW TO PROCEED WITH TROUBLESHOOTING

·

If the entry and start system (for Start Function) has been canceled, enable the system before performing troubleshooting.

Click here

Click hereVehicle Interior>THEFT DETERRENT / KEYLESS ENTRY>ENTRY AND START SYSTEM (for Start Function, HV Model)>CUSTOMIZE PARAMETERS

·

Inspect the fuses for circuits related to this system before performing the following procedure.

·

Before replacing the certification ECU (smart key ECU assembly) or electrical key transmitter sub-assembly, refer to Service Bulletin.

·

After completing repairs, confirm that the problem does not recur.

·

After repair, confirm that no DTCs are output by performing "DTC Output Confirmation Operation".

·

When disconnecting the cable from the negative (-) auxiliary battery terminal, some systems need to be initialized after the cable is reconnected.

Click hereGeneral>SETUP>WHEN DISCONNECTING OR RECONNECTING BATTERY TERMINAL>WORK PROCEDURE



PROCEDURE

1.CHECK POWER SWITCH CONDITION
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

With the brake pedal released, check that pressing the power switch causes the power source mode to change.


Result:
Result Proceed to
Power source mode changes : Off → ACC → ON → off A
Power source mode does not change to ACC or ON B
Power source mode changes to ON but not to ACC C
Power source mode changes to ACC but not to ON D



A

2.READ VALUE USING GTS (STOP LIGHT SWITCH)

B

C

D

2.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Stop Light Switch State of brake pedal OFF or ON OFF: Brake pedal released
ON: Brake pedal depressed
·

Use this item to determine if the stop light switch assembly is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.

·

If the stop light switch assembly is malfunctioning, the hybrid control system can be started by pressing and holding the power switch for a certain period of time.


Body Electrical > Power Source Control > Data List
Tester Display
Stop Light Switch
50003 454 206
OK:

The GTS display changes correctly in response to the brake pedal operation.



Result:
Proceed to
OK
NG



OK

3.READ VALUE USING GTS (SHIFT P SIGNAL)

NG

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
3.READ VALUE USING GTS (SHIFT P SIGNAL)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Shift P Signal Shift position P OFF or ON OFF: Shift lever not in P
ON: Shift lever in P
·

Use this item to determine if the shift position switch is malfunctioning.

·

The hybrid control system cannot be started when this item is OFF.


Body Electrical > Power Source Control > Data List
Tester Display
Shift P Signal
50003 454 205
OK:

The GTS display changes correctly in response to the shift lever operation.



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (POWER SUPPLY CONDITION)

NG

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
4.READ VALUE USING GTS (POWER SUPPLY CONDITION)
a.

Read the Data List according to the display on the GTS.

Body Electrical > Power Source Control > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Power Supply Condition Power supply state OFF, ACC ON, IGR ON, IGP ON or Starter ON OFF: Ignition switch off
ACC ON: Ignition switch ACC
IGR ON: Ignition switch ON
IGP ON: Ignition switch ON
Starter ON: Sending hybrid control system start request signal
-
Body Electrical > Power Source Control > Data List
Tester Display
Power Supply Condition
50003 454 405
NOTICE:

Check that the key indicator display is displayed on the multi-information display in the combination meter assembly, and then press the power switch.


OK:

The GTS display changes correctly in response to the power switch operation.



Result:
Proceed to
OK
NG



OK

5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)

NG

7.CHECK STEERING LOCK FUNCTION
5.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - HYBRID VEHICLE CONTROL ECU)
a.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H44 hybrid vehicle control ECU connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-2 (ST2) - H44-4 (ST2) Always Below 1 Ω
H45-2 (ST2) or H44-4 (ST2) - Other terminals and body ground Always 10 kΩ or higher



d.

Connect the H45 certification ECU (smart key ECU assembly) connector.


Result:
Proceed to
OK
NG



OK

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

6.CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
a.

Connect the H45 certification ECU (smart key ECU assembly) connector.


b.

Connect the H44 hybrid vehicle control ECU connector.


c.
B574625C10
1.313,0.031 1.729,0.271 0.417,0.24 1.094,1.896 1.229,1.896 1.229,1.896 2.115,0.688 true 0.146,0.125 0.458,0.323 0.313,0.198 10 false *a 1.396,0.083 1.708,0.281 0.313,0.198 10 false H45 0.813,1.844 1.125,2.042 0.313,0.198 10 false ST2
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H45-2 (ST2) - Body ground With the brake pedal depressed, the power switch is pressed and held → After approx. 3 sec. has elapsed, the power switch is released 8.5 V or higher → 1.0 V or less



Result:
Proceed to
OK
NG



OK

NG

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

7.CHECK STEERING LOCK FUNCTION
a.

Check that the steering unlocks when the ignition switch is turned to ACC.

OK:

The steering unlocks.



Result:
Proceed to
OK
NG



OK

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)

NG

8.CHECK SECURITY INDICATOR LIGHT (IMMOBILISER FUNCTION UNSET)
a.

Get into the vehicle while carrying an electrical key transmitter sub-assembly.


b.

Move the shift lever to P.


c.

Press the power switch with the brake pedal released and check that the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.

OK:

The security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.


HINT:

The immobiliser function can be determined to be operating correctly if the security indicator light changes from blinking to off at the same time that the power source mode changes to ACC.



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

9.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C07
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.667,0.073 1.979,0.271 0.313,0.198 10 false H46 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift lever in P → Shift lever not in P 9 V or higher → 2.76 V or less



Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
10.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - SHIFT LOCK CONTROL UNIT ASSEMBLY)
a.

Disconnect the H46 certification ECU (smart key ECU assembly) connector.


b.

Disconnect the H20 shift lock control unit assembly connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H46-14 (P) - H20-3 (P2) Always Below 1 Ω
H46-14 (P) or H20-3 (P2) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

11.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

11.CHECK SHIFT LOCK CONTROL UNIT ASSEMBLY
a.
B574624C08
1.583,0.042 1.979,0.25 0.396,0.208 2.271,1.885 2.146,1.885 2.146,1.885 1.698,0.792 true 0.146,0.135 0.458,0.333 0.313,0.198 10 false *a 1.667,0.073 1.979,0.271 0.313,0.198 10 false H46 2.333,1.802 2.698,1.99 0.365,0.188 10 false P
*a Component with harness connected
(Certification ECU (Smart Key ECU Assembly))


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
H46-14 (P) - Body ground Shift lever in P 9 V or higher



Result:
Result Proceed to
OK (for TMC Made) A
OK (for TMMF Made) B
NG C



A

B

C

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

12.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - POWER SOURCE AND BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.
E409581C43
1.469,0.115 1.969,0.365 0.5,0.25 0.917,1.833 1.083,1.833 1.083,1.833 1.271,1.354 true 2.667,1.833 2.479,1.833 2.479,1.833 2.302,1.365 true 0.115,0.125 0.427,0.281 0.313,0.156 10 false *a 1.594,0.156 1.906,0.313 0.313,0.156 10 false A63 2.75,1.76 3.063,1.917 0.313,0.156 10 false B 0.583,1.76 1.031,1.969 0.448,0.208 10 false GND
*a Front view of wire harness connector
(to Stop Light Switch Assembly)


Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A63-7 (B) - Body ground Ignition switch off 11 to 14 V



c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A63-2 (GND) - Body ground Always Below 1 Ω



Result:
Proceed to
OK
NG



OK

13.CONFIRM MODEL

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

13.CONFIRM MODEL
a.

Choose the model to be inspected.


Result:
Result Proceed to
for LHD A
for TMC Made RHD B
for TMMF Made RHD C



A

14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

B

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)

C

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
14.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A68 hybrid vehicle control ECU connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the H20 shift lock control unit assembly connector.


f.

Disconnect the A34 brake booster control computer connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-21 (STP1) - A63-3 (L) Always Below 1 Ω
H45-21 (STP1) or A63-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

15.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

15.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

16.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A68 hybrid vehicle control ECU connector.


d.

Disconnect the A38 skid control ECU (brake booster with master cylinder assembly) connector.


e.

Disconnect the H20 shift lock control unit assembly connector.


f.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-21 (STP1) - A63-3 (L) Always Below 1 Ω
H45-21 (STP1) or A63-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

17.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

17.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY

18.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)
a.

Disconnect the A63 stop light switch assembly connector.


b.

Disconnect the H45 certification ECU (smart key ECU assembly) connector.


c.

Disconnect the A68 hybrid vehicle control ECU connector.


d.

Disconnect the A39 skid control ECU (brake actuator assembly) connector.


e.

Disconnect the H20 shift lock control unit assembly connector.


f.

Disconnect the A35 brake booster control computer connector.


g.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
H45-21 (STP1) - A63-3 (L) Always Below 1 Ω
H45-21 (STP1) or A63-3 (L) - Other terminals and body ground Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

19.CHECK STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

19.CHECK STOP LIGHT SWITCH ASSEMBLY
a.

Check the stop light switch assembly.

Click hereVehicle Exterior>LIGHTING (EXT)>STOP LIGHT SWITCH>ON-VEHICLE INSPECTION


Result:
Proceed to
OK
NG



OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

NG

REPLACE STOP LIGHT SWITCH ASSEMBLY