Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0432441 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made) C

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for Gasoline Model TMMF Made)  C050019  Left Front Wheel Speed Sensor Circuit Current Above Threshold  


DESCRIPTION

Refer to DTC C050018

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>C050018

DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from
C050019 Left Front Wheel Speed Sensor Circuit Current Above Threshold This wheel speed sensor signal electrical current value exceeds the threshold value for 0.14 second or more.
·

Front speed sensor LH

·

Speed sensor installation

·

Wire harness and connector

·

Skid control ECU (brake actuator assembly)


Brake

CAUTION / NOTICE / HINT

NOTICE:
·

After replacing the skid control ECU (brake actuator assembly), perform yaw rate and acceleration sensor zero point calibration and system information memorization.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>UTILITY

·

After replacing or removing and installing a speed sensor, perform Dealer Mode (Signal Check) inspection to confirm that the speed sensors are operating correctly.

Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for Gasoline Model TMMF Made)>TEST MODE PROCEDURE



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR GROUND CIRCUIT)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A22 front speed sensor LH connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Pre-procedure2

d.

Turn the ignition switch to ON.


Procedure1

e.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-2 (FL+) - A22-1 (FL-) Ignition switch ON 11 to 14 V



Post-procedure1

f.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG

2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
2.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

Pre-procedure1

a.

Make sure that there is no looseness at the locking part and the connecting part of the connectors.

OK:

The connector is securely connected.



b.

Disconnect the A37 skid control ECU (brake actuator assembly) connector.


c.

Check both the connector case and the terminals for deformation and corrosion.

OK:

No deformation or corrosion.



Procedure1

d.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Condition Specified Condition
A22-1 (FL-) - Body ground Always Below 1.5 V



Post-procedure1

e.

None


Result:
Proceed to
OK
NG



OK

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (FRONT SPEED SENSOR LH - BRAKE ACTUATOR ASSEMBLY)
a.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
A22-2 (FL+) or A37-36 (FL+) - A22-1 (FL-) or A37-37 (FL-) Always 10 kΩ or higher



Result:
Proceed to
OK
NG



OK

4.READ VALUE USING GTS (FL WHEEL SPEED)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.READ VALUE USING GTS (FL WHEEL SPEED)

Pre-procedure1

a.

Reconnect the A37 skid control ECU (brake actuator assembly) connector.


b.

Reconnect the A22 front speed sensor LH connector.


Procedure1

c.

Operate the GTS to check the Data List.

Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
FL Wheel Speed Front speed sensor LH reading Min.: 0.0 km/h (0.0 mph)
Max.: 6553.5 km/h (4072 mph)
Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Chassis > Brake > Data List
Tester Display
FL Wheel Speed
50003 435 14

d.

Drive the vehicle and perform a road test.

OK:

The values change in accordance with the operation of the vehicle.


NOTICE:

Perform the above inspection before removing the sensor and connector.



Post-procedure1

e.

Turn the ignition switch off.


Result:
Proceed to
OK
NG



OK

NG