If the main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more, DTC B232588 will be stored.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area |
|---|---|---|---|
| B232588 | Door LIN Bus off | The main body ECU (multiplex network body ECU) detects a communication error with an ECU connected to the door bus lines for 8 seconds or more. | ·
Main body ECU (multiplex network body ECU) ·
Power distribution box assembly ·
Multiplex network master switch assembly ·
Front power window regulator motor assembly (driver door) ·
Front power window regulator motor assembly (front passenger door) ·
Front power window regulator motor assembly (rear RH door) ·
Front power window regulator motor assembly (rear LH door) ·
Double lock door control relay assembly (w/ Double Locking System) ·
Wire harness or connector |
When a power window regulator motor assembly is replaced or removed and reinstalled, it is necessary to perform initialization.
Click hereVehicle Exterior>WINDOW / GLASS>POWER WINDOW CONTROL SYSTEM>INITIALIZATION
Before replacing the main body ECU (multiplex network body ECU), refer to Service Bulletin.
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Check vehicle type.
| Result | Proceed to |
|---|---|
| for RHD | A |
| for LHD | B |
A
B
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B232588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the K7 front power window regulator motor assembly (driver door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B232187 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the K5 multiplex network master switch assembly connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B120687 and B232187 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232287 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232387 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232387 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the H42 double lock door control relay assembly connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232487 is not output | B |
A
B
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the power distribution box assembly connector.
Disconnect the K7 front power window regulator motor assembly (driver door) connector.
Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-15 (LIN2) - Body ground | Always | 10 kΩ or higher |
| MB-15 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 4E power distribution box assembly connector.
Disconnect the K7 front power window regulator motor assembly (driver door) connector.
Disconnect the L7 front power window regulator motor assembly (front passenger door) connector.
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4E-17 - Body ground | Always | 10 kΩ or higher |
| 4E-17 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the K5 multiplex network master switch assembly connector.
Disconnect the K7 front power window regulator motor assembly (driver door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| K5-16 (LIN2) or K7-9 (LIN) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Check for DTCs.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B232588 is not output | B |
A
B
Click hereGeneral>INTRODUCTION>HOW TO TROUBLESHOOT ECU CONTROLLED SYSTEMS>HOW TO PROCEED WITH TROUBLESHOOTING
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the L7 front power window regulator motor assembly (driver door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B232187 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the L13 multiplex network master switch assembly connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232588 is output | A |
| DTC B120687 and B232187 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232287 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232387 is not output | B |
A
B
Clear the DTCs.
| Proceed to |
|---|
| NEXT |
NEXT
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
After 10 seconds have elapsed, check if the DTC is output.
| Result | Proceed to |
|---|---|
| DTC B232587 is output | A |
| DTC B232487 is not output | B |
A
B
Remove the main body ECU (multiplex network body ECU) from the power distribution box assembly.
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
Reconnect the power distribution box assembly connector.
Disconnect the L7 front power window regulator motor assembly (driver door) connector.
Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| MB-15 (LIN2) - Body ground | Always | 10 kΩ or higher |
| MB-15 (LIN2) - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the 4E power distribution box assembly connector.
Disconnect the L7 front power window regulator motor assembly (driver door) connector.
Disconnect the K7 front power window regulator motor assembly (front passenger door) connector.
Disconnect the M4 rear power window regulator motor assembly (rear RH door) connector.
Disconnect the N4 rear power window regulator motor assembly (rear LH door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| 4E-17 - Body ground | Always | 10 kΩ or higher |
| 4E-17 - Other terminals | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
for LHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for LHD)>REMOVAL
for RHD: Click herePower Source / Network>POWER DISTRIBUTION>MAIN BODY ECU (for RHD)>REMOVAL
NG
Disconnect the L13 multiplex network master switch assembly connector.
Disconnect the L7 front power window regulator motor assembly (driver door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| L13-16 (LIN2) or L7-9 (LIN) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG