The radio and display receiver assembly, map light assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.
Using this circuit, the radio and display receiver assembly sends power to the map light assembly and telephone microphone assembly, and the map light assembly and telephone microphone assembly sends microphone signals to the radio and display receiver assembly.
Depending on the parts that are replaced during vehicle inspection or maintenance, performing initialization, registration or calibration may be needed. Refer to Precaution for Navigation System.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PRECAUTION
Enter the "Microphone Check" screen. Refer to Check Microphone (Input to navigation ECU) in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Enter the "Microphone Check" screen. Refer to Check Microphone (Input to radio and display receiver assembly) in Operation Check.
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>OPERATION CHECK
When voice is input into the microphone, check that the microphone input level meter changes according to the input voice.
Check result is normal.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H81 radio and display receiver assembly connector.
Disconnect the H82 navigation ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H81-25 (MCO+) - H82-13 (MIC+) | Always | Below 1 Ω |
| H81-26 (MCO-) - H82-14 (MIC-) | Always | Below 1 Ω |
| H81-25 (MCO+) or H82-13 (MIC+) - Body ground | Always | 10 kΩ or higher |
| H81-26 (MCO-) or H82-14 (MIC-) - Body ground | Always | 10 kΩ or higher |
| H81-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H82 navigation ECU connector.
Turn the ignition switch to ACC.
| *a | Front view of wire harness connector
(to Navigation ECU) |
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | H82-13 (MIC+) - H82-14 (MIC-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Check the vehicle type.
| Result | Proceed to |
|---|---|
| for TMC Made | A |
| for TMMF Made without TelephoneTransceiver Assembly | B |
| for TMMF Made with TelephoneTransceiver Assembly | C |
A
B
C
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V7 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V7-13 (SNS2) | Always | Below 1 Ω |
| H80-23 (MACC) - V7-16 (MACC) | Always | Below 1 Ω |
| H80-21 (MIN+) - V7-15 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - V7-14 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V7-13 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-23 (MACC) or V7-16 (MACC) - Body ground | Always | 10 kΩ or higher |
| H80-21 (MIN+) or V7-15 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V7-14 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H80-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V7 map light assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly) |
Connect an oscilloscope to terminals 15 (MCO+) and 14 (MCO-) of the V7 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V7-15 (MCO+) - V7-14 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V7-13(SNS2) - MC-1(SNS2) | Always | Below 1 Ω |
| V7-16(MACC) - MC-5(MACC) | Always | Below 1 Ω |
| V7-15(MCO+) - MC-3(MIC+) | Always | Below 1 Ω |
| V7-14(MCO-) - MC-2(MIC-) | Always | Below 1 Ω |
| V7-13(SNS2) - Body ground | Always | 10 kΩ or higher |
| V7-16(MACC) - Body ground | Always | 10 kΩ or higher |
| V7-15(MCO+) - Body ground | Always | 10 kΩ or higher |
| V7-14(MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V6-15 (SNS2) | Always | Below 1 Ω |
| H80-23 (MACC) - V6-2 (MACC) | Always | Below 1 Ω |
| H80-21 (MIN+) - V6-3 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H80-25 (SNS2) or V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| H80-23 (MACC) or V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| H80-21 (MIN+) or V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V6 map light assembly connector.
| *a | Component with harness connected
(Radio and Display Receiver Assembly) |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H80-23 (MACC) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-24 (SGND) - Body ground | Always | Below 1 Ω |
| H80-22 (MIN-) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Connect the H80 radio and display receiver assembly connector.
Connect the V6 map light assembly connector.
Turn the ignition switch to ACC.
| *a | Component with harness connected
(Map Light Assembly) |
Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V6-3 (MCO+) - V6-4 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
Click hereAudio / Visual / Telematics>NAVIGATION / MULTI INFO DISPLAY>NAVIGATION SYSTEM>PROBLEM SYMPTOMS TABLE
NG
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the MC telephone microphone assembly connector.
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-2 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V6-3 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-25 (SNS2) - V6-15 (SNS2) | Always | Below 1 Ω |
| H80-25 (SNS2) or V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H80 radio and display receiver assembly connector.
Disconnect the H85 telephone transceiver assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H80-21 (MIN+) - H85-16 (MCO+) | Always | Below 1 Ω |
| H80-22 (MIN-) - H85-32 (MCO-) | Always | Below 1 Ω |
| H80-21 (MIN+) or H85-16 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H80-22 (MIN-) or H85-32 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H80-24 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
Disconnect the H85 telephone transceiver assembly connector.
Disconnect the V6 map light assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - V6-2 (MACC) | Always | Below 1 Ω |
| H85-6 (MCI+) - V6-3 (MCO+) | Always | Below 1 Ω |
| H85-7 (MCI-) - V6-4 (MCO-) | Always | Below 1 Ω |
| H85-5 (MCVD) or V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| H85-6 (MCI+) or V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| H85-7 (MCI-) or V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| H85-23 (SGND) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Remove the telephone transceiver assembly with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
|---|---|---|
| H85-5 (MCVD) - Body ground | Ignition switch ACC | 4 to 6 V |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H85-7 (MCI-) - Body ground | Always | Below 1 Ω |
| H85-23 (SGND) - Body ground | Always | Below 1 Ω |
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Map Light Assembly) |
Check the output waveform.
Remove the map light assembly with the connector(s) still connected.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.
Turn the ignition switch to ACC.
Connect an oscilloscope to terminals 3 (MCO+) and 4 (MCO-) of the V6 map light assembly connector.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | V6-3 (MCO+) - V6-4 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component with harness connected
(Telephone Transceiver Assembly) |
Check the output waveform.
Remove the telephone transceiver assembly with the connector(s) still connected.
Click hereAudio / Visual / Telematics>TELEMATICS>TELEMATICS TRANSCEIVER>REMOVAL
Connect an oscilloscope to terminals 16 (MCO+) and 32 (MCO-) of the H85 telephone transceiver assembly connector.
Turn the ignition switch to ACC.
Check the signal waveform according to the condition(s) in the table below.
| Item | Condition |
|---|---|
| Measurement terminal | H85-16 (MCO+) - H85-32 (MCO-) |
| Tool setting | 50 mV/DIV., 500 ms/DIV. |
| Vehicle condition | 1.
Turn the ignition switch to ACC. 2.
Sound is input to the map light assembly when the user is closer than 125 mm from the map light assembly sound holes. |
The waveform is similar to that shown in the illustration.
The oscilloscope waveform shown in the illustration is an example for reference only.
| Proceed to |
|---|
| OK |
| NG |
OK
NG
| *a | Component without harness connected
(Map Light Assembly (No. 1 Roof Wire Side)) |
| *b | Component without harness connected
(Map Light Assembly (Telephone Microphone Assembly Side)) |
Remove the map light assembly.
Click hereVehicle Interior>LIGHTING (INT)>PERSONAL LIGHT>REMOVAL
Disconnect the telephone microphone assembly connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| V6-15 (SNS2) - MC-1 (SNS2) | Always | Below 1 Ω |
| V6-2 (MACC) - MC-5 (MACC) | Always | Below 1 Ω |
| V6-3 (MCO+) - MC-3 (MIC+) | Always | Below 1 Ω |
| V6-4 (MCO-) - MC-2 (MIC-) | Always | Below 1 Ω |
| V6-15 (SNS2) - Body ground | Always | 10 kΩ or higher |
| V6-2 (MACC) - Body ground | Always | 10 kΩ or higher |
| V6-3 (MCO+) - Body ground | Always | 10 kΩ or higher |
| V6-4 (MCO-) - Body ground | Always | 10 kΩ or higher |
| Proceed to |
|---|
| OK |
| NG |
OK
NG