The ABS solenoid relay and master cylinder cut solenoid valves are built into the brake actuator assembly.
Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor.
When this DTC is stored, the fail-safe function operates and the ABS solenoid relay is turned off to prevent the master cylinder cut solenoid valves from operating.
| DTC No. | Detection Item | DTC Detection Condition | Trouble Area | DTC Output from |
|---|---|---|---|---|
| C13C012 | Brake Pressure Control Solenoid "A" Control Circuit Short to Battery | A short to +B in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C014 | Brake Pressure Control Solenoid "A" Control Circuit Short to Ground or Open | An open or short in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C01C | Brake Pressure Control Solenoid "A" Control Circuit Voltage Out of Range | ·
A current leak in the master cylinder cut solenoid circuit is detected during the self test. ·
The master cylinder cut solenoid valve operation request signal and master cylinder cut solenoid valve operation feedback signal do not match for a certain period of time. |
Skid control ECU (brake actuator assembly) | Brake |
| C13C01E | Brake Pressure Control Solenoid "A" Control Circuit Resistance Out of Range | An abnormal resistance in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C049 | Brake Pressure Control Solenoid "A" Control Internal Electronic Failure | An internal malfunction in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C912 | Brake Pressure Control Solenoid "B" Control Circuit Short to Battery | A short to +B in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C914 | Brake Pressure Control Solenoid "B" Control Circuit Short to Ground or Open | An open or short in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C91C | Brake Pressure Control Solenoid "B" Control Circuit Voltage Out of Range | ·
A current leak in the master cylinder cut solenoid circuit is detected during the self test. ·
The master cylinder cut solenoid valve operation request signal and master cylinder cut solenoid valve operation feedback signal do not match for a certain period of time. |
Skid control ECU (brake actuator assembly) | Brake |
| C13C91E | Brake Pressure Control Solenoid "B" Control Circuit Resistance Out of Range | An abnormal resistance in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
| C13C949 | Brake Pressure Control Solenoid "B" Control Internal Electronic Failure | An internal malfunction in the master cylinder cut solenoid circuit is detected during the self test. | Skid control ECU (brake actuator assembly) | Brake |
After replacing the skid control ECU (brake actuator assembly), perform acceleration sensor zero point calibration and store system information memorization.
Choose the model to be inspected.
| Result | Proceed to |
|---|---|
| for RHD | A |
| for LHD | B |
A
B
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model TMMF Made RHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT
Click hereBrake>BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS>BRAKE ACTUATOR (for HV Model LHD)>REMOVAL
| Proceed to |
|---|
| NEXT |
NEXT