Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › ELECTRONICALLY CONTROLLED BRAKE SYSTEM (for HV Model TMMF Made) › 2020.07–2021.11
RM36W0E _54 Brake _088016 BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS _0435240 ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made) U

BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS  ELECTRONICALLY CONTROLLED BRAKE SYSTEM(for HV Model TMMF Made)  DATA LIST / ACTIVE TEST  


DATA LIST


NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.


HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Connect the GTS to the DLC3.


d.

Turn the ignition switch to ON.


e.

Enter the following menus: Chassis / Brake Booster / Data List.


f.

Enter the following menus: Chassis / Brake / Data List.


g.

Turn the GTS on.


h.

According to the display on the GTS, read the Data List.

Chassis > Brake Booster > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0, Max.: 16777215 - -
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa, Max.: 23.99 MPa Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
ECB Motor Relay Motor relay operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
ECB Motor Relay2 Motor relay 2 operation request OFF / ON OFF: Relay off
ON: Relay on
ECB: Electronically Controlled Brake System
Quantity of Brake Pedal Stroke Brake pedal stroke amount Min.: 0 mm, Max.: 255 mm Brake pedal released: 0 mm Reading increases when brake pedal is depressed
Brake Pedal Stroke Change Speed Brake pedal stroke rate of change Min.: -2560 mm/s, Max.: 2540 mm/s Brake pedal released or depressed and held: 0 mm/s Brake pedal is being moved: Changes in proportion to the operation speed of the brake pedal
VCSK Voltage Value VCSK voltage value Min.: 0.000 V, Max.: 5.500 V 4.800 to 5.200 V -
+BS Voltage +BS voltage value Min.: 0.0 V, Max.: 25.5 V - Changes in proportion to auxiliary battery voltage
Stroke Sensor (DTS) CH1 SENT Relative displacement sensor (brake booster with master cylinder assembly) CH1 SENT value Min.: 0, Max.: 4095 - -
Stroke Sensor (DTS) CH2 PWM Relative displacement sensor (brake booster with master cylinder assembly) CH2 PWM value Min.: 0 %, Max.: 100 % - -
The Number of Capacitor Operation The Number of Capacitor Operation Min.: 0 Times, Max.: 255 Times - -
Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled - Unit Total Distance Traveled unit km / mile - -
Total Distance Traveled Total distance traveled Min.: 0, Max.: 16777215 - -
FR Wheel Speed Front wheel speed sensor RH reading Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FL Wheel Speed Front wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RR Wheel Speed Rear wheel speed sensor RH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
RL Wheel Speed Rear wheel speed sensor LH reading Min.: 0.0 km/h (0.0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
FR Wheel Acceleration Front wheel RH acceleration Min.: -200.840 m/s2, Max.: 199.271 m/s2 Vehicle stopped: 0.000 m/s2
During deceleration: -200.840 to 0.000 m/s2
During acceleration: 0.000 to 199.271 m/s2
During deceleration/acceleration: Changes continuously
FL Wheel Acceleration Front wheel LH acceleration Min.: -200.840 m/s2, Max.: 199.271 m/s2 Vehicle stopped: 0.000 m/s2
During deceleration: -200.840 to 0.000 m/s2
During acceleration: 0.000 to 199.271 m/s2
During deceleration/acceleration: Changes continuously
RR Wheel Acceleration Rear wheel RH acceleration Min.: -200.840 m/s2, Max.: 199.271 m/s2 Vehicle stopped: 0.000 m/s2
During deceleration: -200.840 to 0.000 m/s2
During acceleration: 0.000 to 199.271 m/s2
During deceleration/acceleration: Changes continuously
RL Wheel Acceleration Rear wheel LH acceleration Min.: -200.840 m/s2, Max.: 199.271 m/s2 Vehicle stopped: 0.000 m/s2
During deceleration: -200.840 to 0.000 m/s2
During acceleration: 0.000 to 199.271 m/s2
During deceleration/acceleration: Changes continuously
Master Cylinder Sensor 1 Master cylinder pressure sensor pressure (value detected by ECU) Min.: -1.00 MPa, Max.: 23.99 MPa Brake pedal released: -1.00 to 0.00 MPa Reading increases when brake pedal is depressed
Zero Point of M/C Memorized zero point value of master cylinder pressure sensor Min.: -12.5 MPa, Max.: 12.4 MPa - -
M/C Sensor Grade Master cylinder pressure sensor change (value detected by ECU) Min.: -30 MPa/s, Max.: 225 MPa/s Brake pedal released or pedal held at constant position: 0 MPa/s When brake pedal is being operated: Changes in proportion with the pedal movement speed
Lateral G Lateral G Min.: -25.105 m/s2, Max.: 24.908 m/s2 Turning right: -25.105 to 0.000 m/s2
Turning left: 0.000 to 24.908 m/s2
During turning: Changes in proportion with lateral acceleration
Forward and Rearward G Forward and rearward G Min.: -25.105 m/s2, Max.: 24.908 m/s2 During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During acceleration/deceleration: Changes in proportion with acceleration
Zero Point of Decele2 Memorized zero point value of lateral G Min.: -25.105 m/s2, Max.: 24.908 m/s2 - -
Zero Point of Decele Memorized zero point value of forward and rearward G Min.: -25.105 m/s2, Max.: 24.908 m/s2 - -
Yaw Rate Sensor Value Yaw rate sensor Min.: -128°/s, Max.: 127°/s Vehicle stopped: 0°/s
Turning right: -128 to 0°/s
Turning left: 0 to 127°/s
-
Zero Point of Yaw Rate Sensor Memorized zero point value of yaw rate sensor Min.: -128°, Max.: 127° - -
Steering Angle Value Steering sensor Min.: -3276.8°, Max.: 3276.7° Turning left: 0.0 to 3276.7°
Turning right: -3276.8 to 0.0°
-
Zero Point of Steering Angle Memorized zero point value of steering sensor Min.: -3276.8°, Max.: 3276.7° - -
MT Voltage Value ABS motor drive voltage value Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to the ABS motor) from the skid control ECU (brake actuator assembly) to the ABS motor relay


Solenoid Power Supply Voltage Solenoid power supply voltage value Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage output (which supplies power to each solenoid) from the skid control ECU (brake actuator assembly) to the ABS solenoid relay


Vehicle Speed Vehicle speed Min.: 0.0 km/h (0 mph), Max.: 6553.5 km/h (4072 mph) Vehicle stopped: 0.0 km/h (0.0 mph) When driving at constant speed: No large fluctuations
Accelerator Opening Angle % Percentage of accelerator pedal opening angle Min.: 0.0%, Max.: 127.5% Accelerator pedal released: 0.0% During accelerator pedal operation: Changes in proportion with the pedal movement
Real Engine Torque Real engine torque Min.: -1024.000 Nm, Max.: 1023.000 Nm - -
Shift Lever Position Shift lever position information fail / 1st / 2nd / 3rd / 4th / 5th / 6th / B / D/M / N / P / R / No input Actual shift lever position for continuously variable transaxle
TRC(TRAC)/VSC OFF Mode TRC/VSC off mode Normal mode (TRC(TRAC) ON/VSC ON) /
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON) /
Not defined /
VSC OFF mode (TRC(TRAC) OFF/VSC OFF)
Normal mode (TRC(TRAC) ON/VSC ON): Normal mode
TRC(TRAC) OFF mode (TRC(TRAC) OFF/VSC ON): TRC off mode
Not defined: Not defined
VSC OFF mode (TRC(TRAC) OFF/VSC OFF): VSC off mode
-
Brake Hold Control Mode Brake hold control mode Out of control mode /
Pressure hold mode /
Pressure release mode /
EPB lock mode
Out of control mode: Brake hold control system is off or brake hold control system is stand-by mode (brake hold standby indicator light is illuminated)
Pressure hold mode: Brake hold control is operating (brake hold operated indicator light is illuminated)
Pressure release mode: Brake hold control is released (brake hold standby indicator light not illuminated)
EPB lock mode: Parking brake is engaged during brake hold control
HINT:
·

EPB stands for electric parking brake

·

If the brake pedal is not depressed for 3 minutes or more after entering pressure hold mode, the system automatically changes to EPB lock mode



FR Target Oil Pressure The value of the target oil pressure applied to the front brake RH Min.: 0.0 MPa, Max.: 20.0 MPa - Operating the brake pedal: Varies depending on the target oil pressure
FL Target Oil Pressure The value of the target oil pressure applied to the front brake LH Min.: 0.0 MPa, Max.: 20.0 MPa - Operating the brake pedal: Varies depending on the target oil pressure
RR Target Oil Pressure The value of the target oil pressure applied to the rear brake RH Min.: 0.0 MPa, Max.: 20.0 MPa - Operating the brake pedal: Varies depending on the target oil pressure
RL Target Oil Pressure The value of the target oil pressure applied to the rear brake LH Min.: 0.0 MPa, Max.: 20.0 MPa - Operating the brake pedal: Varies depending on the target oil pressure
Vehicle Speed Grade Vehicle speed grade Min.: -25.105 m/s2, Max.: 24.908 m/s2 Vehicle stopped: 0.000 m/s2
During deceleration: -25.105 to 0.000 m/s2
During acceleration: 0.000 to 24.908 m/s2
During deceleration/acceleration: Changes continuously
Vehicle Stop Time from IG ON Time vehicle stopped after ignition switch turned to ON Min.: 0 s, Max.: 1275 s - -
Travel Distance from IG ON Driving time after ignition switch turned to ON Min.: 0 s, Max.: 1275 s - -
Stop Light SW Stop light switch assembly (STP terminal input) OFF / ON OFF: Brake pedal released
ON: Brake pedal depressed
HINT:

The brake pedal state is determined using the voltage at terminal STP


Parking Brake SW Parking brake switch assembly OFF / ON OFF: Parking brake released
ON: Parking brake applied
-
Reverse Position Switch Back-up light switch assembly OFF / ON OFF: Shift lever in any position other than R
ON: Shift lever in R
-
Brake Hold Switch Brake hold switch (electric parking brake switch assembly) (HZRI terminal input) OFF / ON OFF: Brake hold switch (electric parking brake switch assembly) OFF
ON: Brake hold switch (electric parking brake switch assembly) ON
HINT:

The brake hold switch (electric parking brake switch assembly) state is determined using the voltage at terminal HZRI


Stop Light Relay Stop light control relay (stop light switch assembly)
(STP2 terminal input)
OFF / ON OFF: Stop light control relay (Stop light switch assembly) OFF
ON: Stop light control relay (Stop light switch assembly) ON
HINT:

The stop light state is determined using the voltage at terminal STP2


Inspection Mode Inspection mode OFF / ON OFF: Normal mode
ON: Inspection mode
HINT:

Refer to utility for details on how to enter inspection mode*1


TRC(TRAC) Control TRC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Engine Control TRC engine control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
TRC(TRAC) Brake Control TRC brake control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel VSC Ctrl Status Front wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel VSC Ctrl Status Front wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel VSC Ctrl Status Rear wheel RH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel VSC Ctrl Status Rear wheel LH VSC control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FR Wheel ABS Ctrl Status Front wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
FL Wheel ABS Ctrl Status Front wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RR Wheel ABS Ctrl Status Rear wheel RH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
RL Wheel ABS Ctrl Status Rear wheel LH ABS control status Out of controlling / Under Controlling Out of controlling: During not control
Under Controlling: During control
-
Fail Status Fail Status OFF / ON OFF: Fail Status off
ON: Fail Status on
-
Fail Control Fail Control Status OFF / ON OFF: Fail Control off
ON: Fail Control on
-
BA Ctrl Status BA control status OFF / ON OFF: During not control
ON: During control
-
PBA Ctrl Status PBA control status OFF / ON OFF: During not control
ON: During control
w/ Pre-collision System
Stop Light Relay State for ECU Control Stop light control relay (stop light switch assembly) status (STPO terminal output) (for ECU control) OFF / ON OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on)
-
Solenoid State for ECU Control ABS solenoid relay status (for ECU control) OFF / ON OFF: ABS solenoid relay not operating
ON: ABS solenoid relay operating
-
Motor State for ECU Control ABS motor relay status (for ECU control) OFF / ON OFF: ABS motor relay not operating
ON: ABS motor relay operating
-
Operation History of IG OFF while Vehicle is moving History of ignition switch turned off when vehicle is in motion OFF / ON OFF: No history
ON: History of ignition switch turned off with vehicle speed 3 km/h (2 mph) or higher
-
Dealer Mode Dealer Mode (Signal Check mode or Calibration mode) status OFF / ON OFF: Normal mode
ON: Dealer Mode (Signal Check mode or Calibration mode)
HINT:
·

for details on Dealer Mode (Signal Check), refer to test mode procedure*2

·

for details on Dealer Mode (Calibration), refer to utility*3



Zero Point Memory State of Steering Angle Sensor Steering sensor zero point memorization status Zero point is not memorized / Zero point is memorized -
HINT:

The steering sensor zero point is acquired when the vehicle is being driven in a straight line at a speed of 15 km/h (9 mph) or more for approximately 1 second


Regenerative Cooperation Regenerative cooperation OFF / ON OFF: Not operating
ON: Operating
-
TRC(TRAC)/VSC OFF SW VSC OFF switch (CSW terminal input) OFF / ON OFF: VSC OFF switch OFF
ON: VSC OFF switch ON
-
Reservoir Warning SW Brake fluid level warning switch OFF / ON OFF: Reservoir level normal
ON: Reservoir level low
-
Brake Hold Ready Brake hold control permission status Not in stand-by mode / Stand-by mode Not in stand-by mode: Brake hold function not operating (brake hold indicator not illuminated)
Stand-by mode: Brake hold function stand-by state (brake hold indicator illuminated)
-
Quantity of Brake Pedal Stroke Brake pedal stroke amount Min.: 0 mm, Max.: 255 mm Brake pedal released: 0 mm Reading increases when brake pedal is depressed
FR Regenerative Request FR regenerative request torque Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
FR Regenerative Operation FR regenerative operation torque Min.: 0 Nm, Max.: 1048560 Nm - Changes according to brake pedal force (When depressing the brake pedal lightly after reaching 30 km/h (19 mph) or more, avoiding sudden braking.)
VCSK Voltage Value VSK2 voltage value Min.: 0.000 V, Max.: 5.500 V 4.800 to 5.200 V -
ABS Solenoid (SRLR) Rear pressure reduction solenoid LH status OFF / ON OFF: Not Operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRLH) Rear pressure holding solenoid LH status OFF / ON OFF: Not Operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRR) Rear pressure reduction solenoid RH status OFF / ON OFF: Not Operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SRRH) Rear pressure holding solenoid RH status OFF / ON OFF: Not Operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLR) Front pressure reduction solenoid LH status OFF / ON OFF: Not Operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFLH) Front pressure holding solenoid LH status OFF / ON OFF: Not Operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRR) Front pressure reduction solenoid RH status OFF / ON OFF: Not Operating
ON: Operating (pressure reduction)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


ABS Solenoid (SFRH) Front pressure holding solenoid RH status OFF / ON OFF: Not Operating
ON: Operating (pressure holding)
HINT:

The solenoid valve controls the brake fluid pressure of the wheel cylinder of the vehicle


TRC(TRAC)/VSC Solenoid (SM2) Master cylinder cut solenoid (Brake Pressure Control Solenoid "B") status OFF / ON OFF: Not Operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


TRC(TRAC)/VSC Solenoid (SM1) Master cylinder cut solenoid (Brake Pressure Control Solenoid "A") status OFF / ON OFF: Not Operating
ON: Operating (pressure regulation)
HINT:

Depending on the operating conditions, the master cylinder cut solenoid valves regulate the brake fluid pressure generated by the pump motor


TRC(TRAC)/VSC Solenoid (SRC2) Reservoir cut solenoid (Brake Pressure Control Solenoid "D") status OFF / ON OFF: Not Operating
ON: Operating (brake fluid supplied to pump motor)
HINT:

When the brakes are operating, the reservoir cut solenoid valves supply brake fluid from the brake master cylinder reservoir assembly to the pump motor as necessary


TRC(TRAC)/VSC Solenoid (SRC1) Reservoir cut solenoid (Brake Pressure Control Solenoid "C") status OFF / ON OFF: Not Operating
ON: Operating (brake fluid supplied to pump motor)
HINT:

When the brakes are operating, the reservoir cut solenoid valves supply brake fluid from the brake master cylinder reservoir assembly to the pump motor as necessary


ABS Motor Relay ABS motor relay OFF / ON OFF: ABS motor not operating
ON: ABS motor operating
-
STPO Stop light control relay (Stop light switch assembly) status (STPO terminal output) OFF / ON OFF: Stop light control relay (Stop light switch assembly) off (Stop light off)
ON: Stop light control relay (Stop light switch assembly) on (Stop light on)
HINT:

When STPO is ON, the stop light control relay (stop light switch assembly) turns ON and the stop lights illuminate


IGR Voltage IGR terminal voltage value (value detected by ECU) Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
+BS Voltage +BS terminal voltage value (value detected by ECU) Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


+BM Voltage +BM terminal voltage value (value detected by ECU) Min.: 0.0 V, Max.: 25.5 V Ignition switch ON: 11.0 to 14.0 V Changes in proportion to auxiliary battery voltage
HINT:

This is the voltage detected at terminal +BS (which supplies power to each solenoid) of the skid control ECU (brake actuator assembly)


Stroke Sensor (APS) CH1 PWM Brake pedal stroke sensor assembly CH1 PWM value Min.: 0 %, Max.: 100 % - -
Stroke Sensor (APS) CH2 PWM Brake pedal stroke sensor assembly CH2 PWM value Min.: 0 %, Max.: 100 % - -


i.

Enter the following menus: Chassis / Steering Angle Sensor / Data List.


j.

According to the display on the GTS, read the Data List.

Chassis > Steering Angle Sensor > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
Total Distance Traveled Total distance traveled Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit Total distance traveled unit km / mile - -
Steering Angle Signal Information Steering angle value
(Rotation to the left side is positive)
Min.: -3072.0 deg
Max.: 3070.5 deg
Turning left: 0.0 to 3070.5 deg
Turning right: -3072.0 to 0.0 deg
During steering operation: Changes in proportion with steering wheel rotation
Sensor Malfunction Factor (Current) Sensor malfunction factor (current) Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck - -
Sensor Malfunction Factor (Past) Sensor malfunction factor (past) Normal / Angle Velocity / AD / Sensor Element / Steering Angle Value / Steering Angle Value of RAM Stuck - -
Total Distance Traveled (When Sensor Malfunction occurred) Total distance traveled (when sensor malfunction occurred) Min.: 0
Max.: 16777215
- -
Total Distance Traveled - Unit (When Sensor Malfunction occurred) Total distance traveled unit (when sensor malfunction occurred) km / mile - -


CHECK FOR INTERMITTENT PROBLEMS


HINT:

A momentary interruption (open circuit) in the connectors and/or wire harness between the sensors and ECUs can be detected using the Data List function of the GTS.


a.

Turn the ignition switch off.


b.

Check the data related to power supply fluctuations.

HINT:

A momentary interruption (open circuit) cannot be detected for 3 seconds after the ignition switch is turned to ON (initial check).


Chassis > Brake > Data List
Tester Display Measurement Item Range Normal Condition Diagnostic Note
EFI Communication Open EFI communication open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U010087
Yaw Rate Open Yaw rate sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012587
Deceleration Open Acceleration sensor (airbag sensor assembly) open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012587
Steering Open Steering sensor open detection Normal / Under intermittent Normal: Normal
Under intermittent: Momentary interruption
Related DTC: U012687

c.

Push the line graph button to display the line graph.


d.

Check for intermittent shorts, etc.

OK:

Normal is displayed.


HINT:

If "Under intermittent" remains displayed on the GTS, measure the resistance between the skid control ECU (brake actuator assembly) and each sensor or the ECM.



e.

While observing the screen, gently jiggle the connector or wire harness between the ECU and each sensors, or between ECUs.

OK:

Normal is displayed.


HINT:
·

If a momentary interruption occurs and Under intermittent is displayed on the GTS, Under intermittent will remain displayed on the GTS for 1 second after the circuit returns to normal.

C399553E30
0.073,0.073 3.292,0.354 3.219,0.281 10 false Reference: GTS display at momentary interruption 0.208,0.875 1.823,1.292 1.615,0.417 10 false Wire Harness condition 0.948,1.927 1.792,2.26 0.844,0.333 10 false Line Graph 2.656,1.354 3.438,1.667 0.781,0.313 10 false 1 second 4.219,1.354 4.938,1.542 0.719,0.188 10 false 2 seconds 4.083,0.313 5.417,0.677 1.333,0.365 10 false 1.5 seconds 2.438,0.313 3.438,0.552 1,0.24 10 false 0.5 seconds 5.656,1.76 6.927,2.073 1.271,0.313 10 false Under intermittent 5.667,2.135 6.417,2.469 0.75,0.333 10 false Normal 5.625,0.708 7.104,1 1.479,0.292 10 false Momentary interruption 5.635,1.073 6.385,1.396 0.75,0.323 10 false Normal

·

If the display changes, this indicates that there has been a momentary interruption (open circuit) in the connector and/or wire harness. In this case, repair or replace the connectors and/or wire harnesses as one of them is faulty.





ACTIVE TEST


HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed.

Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.


a.

Warm up the engine.


b.

Turn the ignition switch off.


c.

Perform the Active Test to check for incorrect operation or to narrow down malfunctioning areas.

NOTICE:
·

Although the Active Test automatically turns off the pump motor after approximately 5 seconds in order to protect the motor, do not operate the pump motor repeatedly without sufficient waiting time in between.

·

Although the Active Test automatically turns off each solenoid after approximately 2 seconds in order to protect the solenoid, do not operate the solenoids repeatedly without sufficient waiting time in between.

·

Do not depress the brake pedal when only the pressure release solenoids valves are ON.

·

Do not operate more than one solenoid at the same time, except for when operating the pressure hold solenoid and pressure release solenoid of the same wheel.





Chassis > Brake > Active Test
Tester Display Measurement Item Control Range Restrict Condition Diagnostic Note
EBS Relay Emergency brake signal operation Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


w/ Emergency Brake Signal
Whether the hazard warning lights blink when the EBS Relay is ON can be confirmed
ABS Solenoid Pressure holding solenoid (SFRH, SFLH, SRRH, SRLH)
Pressure reduction solenoid (SFRR, SFLR, SRRR, SRLR)
Solenoid Start (Activate)
Solenoid SFRH / SFLH / SRRH / SRLH / SFRR / SFLR / SRRR / SRLR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


for LHD: Refer to on-vehicle inspection for the brake actuator (for HV Model LHD)*1
for RHD: Refer to on-vehicle inspection for the brake actuator (for HV Model 5 Hub Bolt Type RHD)*2
VSC Solenoid Master cylinder cut solenoid (SMF (SM1), SMR (SM2))
Reservoir cut solenoid ((SRCF (SRC1), SRCR (SRC2))
Solenoid Start (Activate)
Solenoid SMF / SMR / SRCF / SRCR
Vehicle condition:
·

Vehicle stopped

·

Shift lever is in P

·

Apply the parking brake


HINT:

To protect actuator and Solenoid(s), this test will continue for 25 seconds.


Check that the GTS display for the solenoid (SM1, SM2, SRC1 or SRC2) changes to ON/OFF during Solenoid Start (Activate)
Motor Relay ABS motor relay Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


for LHD: Refer to on-vehicle inspection for the brake actuator (for HV Model LHD)*1
for RHD: Refer to on-vehicle inspection for the brake actuator (for HV Model TMMF Made RHD)*2
Stop Lamp Relay Stop light control relay (Stop light switch assembly) Relay OFF / ON Vehicle condition: Vehicle stopped
HINT:

To protect this Actuator and Solenoid, this test will only last 5 seconds.


With the brake pedal released, check that the stop lights illuminate and the value of Stop Light Relay on the GTS changes to ON when Stop Lamp Relay is ON