Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › FRONT SEAT SIDE AIRBAG ASSEMBLY › 2020.07–2020.09
RM36W0E _58 Vehicle Interior _088020 SUPPLEMENTAL RESTRAINT SYSTEMS _0421876 FRONT SEAT SIDE AIRBAG ASSEMBLY N

SUPPLEMENTAL RESTRAINT SYSTEMS  FRONT SEAT SIDE AIRBAG ASSEMBLY  DISPOSAL  


CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.


HINT:
·

Use the same procedure for the driver side and front passenger side.

·

The procedure listed below is for the driver side.



PROCEDURE

Hide 1. PRECAUTION

CAUTION:
·

An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.

·

Do not perform this procedure indoors or on rough roads where safety cannot be ensured. Also, do not deploy SRS parts near residential areas.

·

If this procedure is performed indoors or on rough roads where safety cannot be ensured, unforeseen injuries may occur. Also, the deployment noise creates a nuisance to nearby residents.

B401137



HINT:

When scrapping a vehicle equipped with an SRS or disposing of the front seat side airbag assembly, be sure to deploy the airbag first in accordance with the following procedure. If any abnormality occurs with the airbag deployment, contact the Service Department of the distributor.


Hide 73910A 2.DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (When Installed to Vehicle)

NOTICE:
·

When disposing of the front seat airbag assembly, use an unneeded vehicle to deploy the airbag.

·

Be sure to perform the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Remove the 4 bolts and tilt the front seat assembly LH backward.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REMOVAL


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




e.

Install SST.

i.
B583380N01
2.917,1.094 1.677,1.094 1.677,1.094 1.677,1.354 true 2.552,1.354 2.552,1.104 true 2.948,0.99 3.313,1.208 0.365,0.219 10 true SST

Connect SST to the front seat airbag assembly.

SST
09082-00820  

CAUTION:
B399563

·

Do not deploy if the front seat airbag assembly is loose.

·

If deployed while the front seat airbag assembly is loose, the front seat airbag assembly may fly off and cause serious injuries.




ii.

Connect SST together (09082-00700 and 09082-00820).

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.




f.

Return the front seat assembly LH to its original position.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION

CAUTION:
B420114

Check that there is no looseness in the front seat assembly LH.



g.

Deploy the airbag.

i.
C154370C48
0.458,1.167 0.677,1.167 false 0.677,1.167 0.927,1.396 false 1.604,1.813 1.917,1.969 0.313,0.156 10 false *a 0.177,1.104 0.573,1.323 0.396,0.219 10 false SST
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


ii.

While maintaining sufficient clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage SST wire harness.



iii.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


v.

Press SST activation switch to deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




h.

Remove the front seat airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT SEAT SIDE AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·
B394947

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394948

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

If water is applied to the front seat airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394951

Always wear safety glasses and gloves when handling a deployed front seat airbag assembly.

·

If the front seat airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the front seat airbag assembly in a plastic bag.




i.

Dispose of the front seat airbag assembly.

i.

Place the front seat airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B399354

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399355

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

If water is applied to the front seat airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394952

Always wear safety glasses and gloves when handling a deployed front seat airbag assembly.

·

If the front seat airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394953

Never dispose of a front seat airbag assembly with an undeployed airbag.

·

If an undeployed front seat airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 739H0 3.DISPOSE OF FRONT SEAT CENTER AIRBAG ASSEMBLY (When Installed to Vehicle)

NOTICE:
·

When disposing of the front seat center airbag assembly, use an unneeded vehicle to deploy the airbag.

·

Be sure to perform the following procedure when deploying the airbag.



HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Remove the 4 bolts and tilt the front seat assembly LH backward.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>REMOVAL


d.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




e.

Install SST.

i.
B583381N01
0.906,0.781 0.906,0.448 0.906,0.448 2.01,0.448 true 1.844,0.792 1.844,0.458 true 2.042,0.333 2.406,0.521 0.365,0.188 10 true SST

Connect SST to the front seat center airbag assembly.

SST
09082-00820  

CAUTION:
B583382

·

Do not deploy if the front seat center airbag assembly is loose.

·

If deployed while the front seat center airbag assembly is loose, the front seat center airbag assembly may fly off and cause serious injuries.




ii.

Connect SST together (09082-00700 and 09082-00820).

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock.




f.

Return the front seat assembly LH to its original position.

Click hereVehicle Interior>SEAT>FRONT SEAT ASSEMBLY>INSTALLATION

CAUTION:
B399563

Check that there is no looseness in the front seat assembly LH.



g.

Deploy the airbag.

i.
C154370C48
0.458,1.167 0.677,1.167 false 0.677,1.167 0.927,1.396 false 1.604,1.813 1.917,1.969 0.313,0.156 10 false *a 0.177,1.104 0.573,1.323 0.396,0.219 10 false SST
*a 10 m (32.8 ft.) or more


Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.


ii.

While maintaining sufficient clearance for SST wire harness in the front side window, close all doors and windows of the vehicle.

CAUTION:
B394904

·

Do not deploy with all the doors and door windows open.

·

If deployed with all the doors and door windows open, dust and gas may enter the eyes or be breathed in.



NOTICE:

Take care not to damage SST wire harness.



iii.

Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.


iv.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


v.

Press SST activation switch to deploy the airbag.

CAUTION:
B400936

·

Do not deploy with people inside or around the vehicle.

·

If deployed with people inside or around the vehicle, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




h.

Remove the front seat center airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT SEAT SIDE AIRBAG ASSEMBLY>REMOVAL

CAUTION:
·
B394947

The front seat center airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B394948

Do not apply water etc. to a front seat center airbag assembly with a deployed airbag.

·

If water is applied to the front seat center airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394951

Always wear safety glasses and gloves when handling a deployed front seat center airbag assembly.

·

If the front seat center airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·

After removal, quickly seal the front seat center airbag assembly in a plastic bag.




i.

Dispose of the front seat center airbag assembly.

i.

Place the front seat center airbag assembly in a plastic bag, tie it tightly and dispose of it according to local regulations.

CAUTION:
·
B399354

The front seat center airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399355

Do not apply water etc. to a front seat center airbag assembly with a deployed airbag.

·

If water is applied to the front seat center airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394952

Always wear safety glasses and gloves when handling a deployed front seat center airbag assembly.

·

If the front seat center airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394953

Never dispose of a front seat center airbag assembly with an undeployed airbag.

·

If an undeployed front seat center airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.





Hide 73910A 4.DISPOSE OF FRONT SEAT AIRBAG ASSEMBLY (When not Installed to Vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.





e.
B104882C91
2.854,0.99 3.094,1.167 0.24,0.177 10 false *a
*a Wire Diameter
V100155

Stripped Wire


Using braided wire, tie down the front seat airbag assembly to an unneeded tire.

Wire:

Cross-sectional area of stripped wire

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the front seat airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.
B279752

Install the 2 nuts to the front seat airbag assembly.


ii.
B279753

Wind 2 or more wires around the stud bolts of the front seat airbag assembly as shown in the illustration.


iii.
B279754C01
0.635,1.417 0.865,1.656 0.229,0.24 10 *b 1.177,0.021 1.458,0.302 0.281,0.281 10 *a
*a Width
*b Inner Diameter


Position the front seat airbag assembly inside the tire with the airbag deployment side facing inward.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the front seat airbag assembly may break loose when the airbag is deployed.

·
B399353C03
0.896,1.813 1.354,1.813 true 0.719,1.729 1.031,1.885 0.313,0.156 10 false *a
*a Remove looseness
V100155

Deployment Side


Always tie down the front seat airbag assembly with the airbag deployment side facing inside the tire as shown in the illustration.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tires.




f.

Install SST.

i.
B279755N01
2.646,1.396 2.854,1.396 false 2.906,1.323 3.292,1.542 0.385,0.219 10 SST

Connect SST to the front seat airbag assembly.

SST
09082-00820  



g.

Place the tires.

i.
B530117C01
2.417,0.719 2.417,1.719 2.417,1.719 2,1.719 true 2,0.719 2.75,0.719 true 1.99,1.417 2.406,1.417 true 1.99,0.917 2.406,0.917 true 2.802,0.604 3.115,0.802 0.313,0.198 10 false *a
*a Tires (2 or more)


Place at least 2 tires under the tire to which the front seat airbag assembly is tied.


ii.

Place at least 2 tires onto the tire to which the front seat airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




h.

Install SST.

i.
B279757C05
1.417,2.635 2.385,2.948 2.385,2.948 1.99,2.635 true 2.438,2.948 2.76,3.135 0.323,0.188 10 false SST 1.167,2.99 1.396,3.167 0.229,0.177 10 false *a
*a 10 m (32.8 ft.) or more


Connect SST together (09082-00700 and 09082-00820).

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tires.



i.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat airbag assembly is tied.


iii.

Press SST activation switch to deploy the airbag.

CAUTION:
B401768

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




j.

Dispose of the front seat airbag assembly.

CAUTION:
·
B399354

The front seat airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399355

Do not apply water etc. to a front seat airbag assembly with a deployed airbag.

·

If water is applied to the front seat airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394952

Always wear safety glasses and gloves when handling a deployed front seat airbag assembly.

·

If the front seat airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394953

Never dispose of a front seat airbag assembly with an undeployed airbag.

·

If an undeployed front seat airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat airbag assembly from the tire.


ii.

Place the front seat airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.



Hide 739H0 5.DISPOSE OF FRONT SEAT CENTER AIRBAG ASSEMBLY (When not Installed to Vehicle)

NOTICE:

Be sure to perform the following procedure when deploying the airbag.


HINT:

Prepare a battery as the power source to deploy the airbag.


a.
C110371N08
0.99,1.208 0.792,0.771 0.792,0.771 0.646,0.771 false 0.323,0.688 0.781,0.885 0.458,0.198 10 SST

Check the function of SST.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>STEERING PAD>DISPOSAL

SST
09082-00700  



c.

Disconnect the cable from the negative (-) auxiliary battery terminal.


CAUTION:
B422343

·

Wait at least 90 seconds after disconnecting the cable from the negative (-) auxiliary battery terminal to disable the SRS system.

·

If the airbag deploys for any reason, it may cause a serious accident.




d.

Remove the front seat center airbag assembly.

Click hereVehicle Interior>SUPPLEMENTAL RESTRAINT SYSTEMS>FRONT SEAT SIDE AIRBAG ASSEMBLY>REMOVAL


e.
B104882C91
2.854,0.99 3.094,1.167 0.24,0.177 10 false *a
*a Wire Diameter
V100155

Stripped Wire


Using braided wire, tie down the front seat center airbag assembly to an unneeded tire.

Wire:

Cross-sectional area of stripped wire

1.25 mm2 (0.0019 in.2) or more


CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the front seat center airbag assembly, it may snap when the airbag is deployed. Always use a wire for vehicle use with a cross-sectional area of at least 1.25 mm2 (0.0019 in.2).


HINT:

To calculate the area of the cross-sectional area of stripped wire:

Area = 3.14 x (Diameter)2 / 4


i.
B279752

Install the 2 nuts to the front seat center airbag assembly.


ii.
B279753

Wind 2 or more wires around the stud bolts of the front seat center airbag assembly as shown in the illustration.


iii.
B279754C01
0.635,1.417 0.865,1.656 0.229,0.24 10 *b 1.177,0.021 1.458,0.302 0.281,0.281 10 *a
*a Width
*b Inner Diameter


Position the front seat center airbag assembly inside the tire with the airbag deployment side facing inward.

Minimum tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)


CAUTION:
·

Make sure that the wires are tight. If there is slack in the wires, the front seat center airbag assembly may break loose when the airbag is deployed.

·
B399353C03
0.896,1.813 1.354,1.813 true 0.719,1.729 1.031,1.885 0.313,0.156 10 false *a
*a Remove looseness
V100155

Deployment Side


Always tie down the front seat center airbag assembly with the airbag deployment side facing inside the tire as shown in the illustration.



NOTICE:

The tire may be damaged by the airbag deployment, so use an unneeded tires.




f.

Install SST.

i.
B279755N01
2.646,1.396 2.854,1.396 false 2.906,1.323 3.292,1.542 0.385,0.219 10 SST

Connect SST to the front seat center airbag assembly.

SST
09082-00820  



g.

Place the tires.

i.
B530117C01
2.417,0.719 2.417,1.719 2.417,1.719 2,1.719 true 2,0.719 2.75,0.719 true 1.99,1.417 2.406,1.417 true 1.99,0.917 2.406,0.917 true 2.802,0.604 3.115,0.802 0.313,0.198 10 false *a
*a Tires (2 or more)


Place at least 2 tires under the tire to which the front seat center airbag assembly is tied.


ii.

Place at least 2 tires onto the tire to which the front seat center airbag assembly is tied. The top tire should have a wheel installed.

NOTICE:
·

Do not place SST connector under the tire because it could be damaged.

·

The tires and wheel may be damaged by the airbag deployment, so use unneeded tires and wheels.




iii.
C223306

Tie the tires together with 2 wires.

CAUTION:

Make sure that the wires are tight. Looseness in the wires will result in the tires breaking loose when the airbag is deployed.




h.

Install SST.

i.
B279757C05
1.417,2.635 2.385,2.948 2.385,2.948 1.99,2.635 true 2.438,2.948 2.76,3.135 0.323,0.188 10 false SST 1.167,2.99 1.396,3.167 0.229,0.177 10 false *a
*a 10 m (32.8 ft.) or more


Connect SST together (09082-00700 and 09082-00820).

SST
09082-00700  

NOTICE:

To avoid damaging SST connector or wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for SST wire harness inside the tire.



ii.

Move SST at least 10 m (32.8 ft.) away from the airbag tied down to the tires.



i.

Deploy the airbag.

i.

Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.


ii.

Check that no one is within a 10 m (32.8 ft.) radius of the tire to which the front seat center airbag assembly is tied.


iii.

Press SST activation switch to deploy the airbag.

CAUTION:
B401768

·

Do not deploy with people around the tire.

·

If deployed with people around the tire, serious injuries may occur.



HINT:

The airbag is deployed as the LED of SST activation switch comes on.




j.

Dispose of the front seat center airbag assembly.

CAUTION:
·
B399354

The front seat center airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.

·

If not left alone for 30 minutes or more, burns may occur when touched.

·
B399355

Do not apply water etc. to a front seat center airbag assembly with a deployed airbag.

·

If water is applied to the front seat center airbag assembly immediately after deployment, burns may occur from the resulting steam.

·
B394952

Always wear safety glasses and gloves when handling a deployed front seat center airbag assembly.

·

If the front seat center airbag assembly is touched without wearing safety glasses and gloves, hot parts may cause burns and dust may enter the eyes.

·
B394953

Never dispose of a front seat center airbag assembly with an undeployed airbag.

·

If an undeployed front seat center airbag assembly is disposed of, and then deploys for any reason, unforeseen injuries may occur.

·

Always wash your hands with water after completing the operation.



i.

Remove the front seat center airbag assembly from the tire.


ii.

Place the front seat center airbag assembly in a plastic bag, tie it tightly, and dispose of it according to local regulations.