Home › Audio / Visual / Telematics › AUDIO / VIDEO › RADIO ANTENNA CORD › 2020.07–2020.09
RM36W0E _56 Audio / Visual / Telematics _088597 AUDIO / VIDEO _0421927 RADIO ANTENNA CORD A

AUDIO / VIDEO  RADIO ANTENNA CORD  INSTALLATION  


PROCEDURE

Hide 86101Q 1.INSTALL NO. 4 ANTENNA CORD SUB-ASSEMBLY

a.
E436756C01
1.333,1.583 1,1.583 true 2.271,2.635 2.521,2.635 true 0.771,1.5 1,1.698 0.229,0.198 10 true *a 2.552,2.542 2.781,2.74 0.229,0.198 10 false *b
*a Nonwoven Tape
*b Rope


Secure a rope to the No. 4 antenna cord sub-assembly with nonwoven tape as shown in the illustration.

NOTICE:
·

As conduction performance may degrade if adhesive from the nonwoven tape contacts the connecting parts of the connector, cover the connector with a plastic bag or similar before applying the nonwoven tape.

·

Make sure that the rope is secured with nonwoven tape to prevent the rope from separating from the No. 4 antenna cord sub-assembly when removing it.




b.
E436757C01
0,0 0,0 false
V113147

Install in this Direction


Install the No. 4 antenna cord sub-assembly as shown in the illustration.

NOTICE:

This step should not be performed with the back door panel sub-assembly removed from the vehicle.



c.
E436759

Engage the claws to install the 2 grommets.


d.

Engage the clamp.


Hide 2.INSTALL NO. 7 ANTENNA CORD SUB-ASSEMBLY

a.
E439179

Engage the clamps to install the No. 7 antenna cord sub-assembly.


b.

Connect the 2 connectors.


Hide 86101V 3.INSTALL NO. 6 ANTENNA CORD SUB-ASSEMBLY

a.
E439178

Engage the clamps to install the No. 6 antenna cord sub-assembly.


b.

Connect the 2 connectors.


Hide 86101R 4.INSTALL NO. 5 ANTENNA CORD SUB-ASSEMBLY

a.
E439177C01
1.75,0.333 2.083,0.333 true 1.458,1.417 1.792,1.417 true 1.208,1.333 1.427,1.552 0.219,0.219 10 true *b 1.5,0.229 1.719,0.448 0.219,0.219 10 true *a
*a Clamp
*b Guide


Engage the guide.


b.

Install the No. 5 antenna cord sub-assembly with the bolt.

Torque:
10 N*m (102 kgf*cm, 7 ft.*lbf)


c.

Engage the clamp.


d.

Connect the 2 connectors.


Hide 67761A 5.INSTALL BACK DOOR TRIM COVER

Hide 67751 6.INSTALL BACK DOOR TRIM BOARD

Hide 86101J 7.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (except Panoramic Moon Roof)

a.

for TMC Made:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap new adhesive tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.

E439180C01
0.667,2.5 0.417,2.25 true 0.583,2.646 0.417,2.896 true 1.667,1.5 1.333,1.75 1.333,1.75 1.25,1.417 true 2.021,1.583 1.854,1.583 1.854,1.583 1.771,1.75 true 3.021,1.708 2.75,1.917 2.75,1.917 2.375,1.646 true 3.49,1.833 3.333,2.083 3.333,2.083 3.25,1.75 true 4.333,1.75 4.135,1.99 4.135,1.99 3.948,1.74 true 5.198,1.729 5,1.969 5,1.969 4.771,1.75 true 4.313,2.792 4.063,2.542 true 5.76,1.833 6.167,1.948 6.167,1.948 5.75,2.167 true 5.406,0.885 5.156,0.635 true 6.146,2.479 5.729,2.479 true 6.083,1.667 5.75,1.667 true 5.396,0.292 5.146,0.531 true 0.281,2.073 0.51,2.25 0.229,0.177 10 false *a 1.229,1.771 1.458,1.948 0.229,0.177 10 true *d 1.667,1.792 1.896,1.969 0.229,0.177 10 true *d 2.656,1.927 2.885,2.104 0.229,0.177 10 true *e 3.25,2.094 3.479,2.271 0.229,0.177 10 true *e 4.052,1.99 4.281,2.135 0.229,0.146 10 true *e 4.917,1.969 5.146,2.115 0.229,0.146 10 true *e 3.938,2.344 4.167,2.521 0.229,0.177 10 true *b 6.208,1.865 6.438,2.01 0.229,0.146 10 true *f 5.417,0.917 5.646,1.094 0.229,0.177 10 true *c 6.188,2.417 6.354,2.563 0.167,0.146 10 true *f 6.083,1.573 6.313,1.75 0.229,0.177 10 true *g 0.302,2.906 0.531,3.083 0.229,0.177 10 false *h 5.448,0.146 5.677,0.323 0.229,0.177 10 false *h 1.677,0.313 1.906,0.49 0.229,0.177 10 false *i 3.531,0.406 3.76,0.583 0.229,0.177 10 false *i
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Adhesive Tape (A)
*e Adhesive Tape (B) *f Adhesive Tape (C)
*g Adhesive Tape (D) *h Protrusion
*i Dent in the Roof Headlining - -
V100155

Adhesive Tape
V113146

Adjustment Area



ii.

Apply the 3 new adhesive tapes (A) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


iii.

Align the No. 2 antenna cord sub-assembly with the dent in the roof headlining as shown in the illustration.


iv.

Apply the 8 new adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


v.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the marking of the roof headlining.


vi.

Apply the 3 new adhesive tapes (C) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

HINT:
·

Turn the connector contact surface upward and secure it with tape.

·

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




vii.

Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining and wrap new adhesive tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


viii.

Apply the new adhesive tape (D) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




b.

for TMMF Made:

i.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap new adhesive tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.

E451700C01
0.667,2.844 0.958,3.167 true 0.656,3.531 0.854,3.365 false 1.625,2.052 1.719,2.354 1.719,2.354 1.979,2.146 true 2.073,2.458 2.271,2.292 true 2.625,2.313 2.906,2.438 2.906,2.438 3.146,2.271 true 3.344,2.375 3.354,2.646 3.354,2.646 3.563,2.417 true 4,2.375 4.083,2.521 4.083,2.521 4.313,2.375 true 4.698,2.385 4.906,2.51 4.906,2.51 5.073,2.313 true 5.563,2.302 5.729,2.479 true 5.323,2.417 5.104,2.74 5.104,2.74 5.427,2.552 true 5.354,3.073 5.083,3.146 true 5.031,0.542 4.771,0.698 true 4.979,1.052 4.771,0.896 true 5.448,3.104 5.104,3.427 true 0.49,2.75 0.802,2.948 0.313,0.198 10 false *a 0.479,3.458 0.792,3.656 0.313,0.198 10 false *g 2.156,0.948 2.469,1.146 0.313,0.198 10 false *h 3.74,2.823 4.052,3.021 0.313,0.198 10 false *h 1.615,2.375 1.813,2.573 0.198,0.198 10 true *d 1.833,2.427 2.031,2.625 0.198,0.198 10 true *d 2.833,2.458 3.031,2.656 0.198,0.198 10 true *d 3.25,2.667 3.448,2.865 0.198,0.198 10 true *d 3.979,2.542 4.177,2.74 0.198,0.198 10 true *d 4.813,2.521 5.01,2.719 0.198,0.198 10 true *d 5.781,2.406 5.979,2.646 0.198,0.24 10 true *f 4.927,2.688 5.083,2.885 0.156,0.198 10 true *e 4.938,3.073 5.094,3.271 0.156,0.198 10 true *e 5.083,0.438 5.313,0.625 0.229,0.188 10 false *g 5.021,1.01 5.25,1.198 0.229,0.188 10 false *c 4.969,3.344 5.125,3.542 0.156,0.198 10 true *b
*a Marking Tape (A) *b Marking Tape (B)
*c Marking Tape (C) *d Adhesive Tape (A)
*e Adhesive Tape (B) *f Adhesive Tape (C)
*g Protrusion *h Dent in the Roof Headlining
V100155

Adhesive Tape
V113146

Adjustment Area



ii.

Align the No. 2 antenna cord sub-assembly with the dent in the roof headlining as shown in the illustration.


iii.

Apply the 11 new adhesive tapes (A) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


iv.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the marking of the roof headlining.


v.

Apply the 3 new adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

HINT:
·

Turn the connector contact surface upward and secure it with tape.

·

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




vi.

Align the marking tape (C) on the No. 2 antenna cord sub-assembly with the protrusion on the rear of the roof headlining and wrap new adhesive tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


vii.

Apply the new adhesive tape (C) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




Hide 86101J 8.INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY (for Panoramic Moon Roof)

a.

Apply new butyl tape along the markings, while making sure that the butyl tape does not extend outside of the markings.

NOTICE:

Apply the tape with even pressure, making sure that the tape does not extend outside of the markings of the roof headlining.


E451712


b.

Align the No. 2 antenna cord sub-assembly with the marking area (A) in the roof headlining as shown in the illustration.

E451701C01
2.323,0.604 2.563,0.688 false 5.719,1.823 6.229,1.813 true 5.74,1.99 6.271,2.094 true 4.885,2.729 5.49,2.625 true 4.938,3.063 5.594,2.646 true 3.083,1.885 3.813,2.396 3.813,2.396 4.135,1.906 true 3.469,1.906 3.813,2.385 3.813,2.385 3.979,1.906 false 2.74,1.875 2.99,2.073 true 2.208,1.719 1.969,2 1.969,2 2.365,1.854 true 1.448,1.146 1.75,1.49 true 0.875,2.417 1.115,2.656 true 4.771,2.99 5.083,3.146 0.313,0.156 10 false *c 6.313,2.021 6.625,2.177 0.313,0.156 10 false *f 6.281,1.688 6.583,2.073 0.302,0.385 10 false *g 2.146,0.5 2.458,0.656 0.313,0.156 10 false *h 4.146,0.469 4.458,0.625 0.313,0.156 10 false *i 4.75,2.646 5.063,2.802 0.313,0.156 10 false *f 3.74,2.417 4.052,2.656 0.313,0.24 10 false *d 3.031,2.021 3.344,2.26 0.313,0.24 10 false *d 1.719,1.938 1.927,2.177 0.208,0.24 10 true *e 1.281,1.052 1.49,1.292 0.208,0.24 10 false *e 0.698,2.323 0.906,2.563 0.208,0.24 10 false *b 4.667,1.917 4.875,2.156 0.208,0.24 10 false *a
*a Marking Area (A) *b Marking Tape (A)
*c Marking Tape (B) *d Adhesive Tape (A)
*e Adhesive Tape (B) *f Adhesive Tape (C)
*g Adhesive Tape (D) *h Protrusion
*i Turn Plate Upward *j Dent in the Roof Headlining
V100155

Adhesive Tape
V113146

Adjustment Area



c.

Apply the 5 new adhesive tapes (A) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


d.

Align the marking tape (A) on the No. 2 antenna cord sub-assembly with the protrusion on the front of the roof headlining and wrap new adhesive tape around the No. 2 antenna cord sub-assembly and protrusion of the roof headlining.


e.

Apply the 3 new adhesive tapes (B) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


f.

Align the marking tape (B) on the No. 2 antenna cord sub-assembly with the marking of the roof headlining.

HINT:
·

Turn the connector contact surface upward and secure it with tape.

·

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.




g.

Apply the 3 new adhesive tapes (C) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.


h.

Apply the new adhesive tape (D) as shown in the illustration to secure the No. 2 antenna cord sub-assembly.

HINT:

Secure the extra length of the No. 2 antenna cord sub-assembly in the adjustment area as shown in the illustration.



Hide 86101 10.INSTALL ANTENNA CORD SUB-ASSEMBLY

a.

for Separate Type:

i.

Engage the guides and clamps to install the antenna cord sub-assembly. (for LHD)

E451694C02
3.635,1.333 4.875,0.896 4.875,0.896 4.313,1.708 true 3.5,2.479 3.219,3.417 3.219,3.417 4.125,2.417 true 4.438,2.302 5.615,1.552 5.615,1.552 4.354,2.708 true 6.396,3.063 6.729,3.26 true 5.729,2.552 6.729,1.677 6.729,1.677 6.427,2.333 true 5.5,3.052 5.844,3.406 true 4.917,0.792 5.115,0.969 0.198,0.177 10 false *a 3.083,3.406 3.281,3.583 0.198,0.177 10 false *a 6.76,3.198 6.958,3.375 0.198,0.177 10 false *b 5.667,1.448 5.865,1.625 0.198,0.177 10 false *a 6.76,1.552 6.948,1.76 0.188,0.208 10 false *a 5.875,3.375 6.083,3.563 0.208,0.188 10 false *a
*a Clamp *b Guide



ii.

Connect the connector.


iii.

Engage the claws.


iv.

Engage the guides and clamps to install the antenna cord sub-assembly. (for RHD)

E451695C02
3.396,2.771 4.083,2.438 4.083,2.438 3.938,3.021 true 5.573,3.021 4.875,3.396 4.875,3.396 4.896,2.813 true 3.042,2.135 3.427,2.146 3.427,2.146 2.844,2.5 true 6.219,3.125 6.5,3.5 true 2.625,2.219 1.729,1.063 1.729,1.063 2.813,1.656 true 3,1.208 1.719,1.063 true 6.542,3.469 6.854,3.625 0.313,0.156 10 false *b 4.104,2.281 4.323,2.448 0.219,0.167 10 true *a 3.469,2.031 3.781,2.188 0.313,0.156 10 false *a 4.75,3.396 4.958,3.604 0.208,0.208 10 false *a 1.542,0.958 1.854,1.115 0.313,0.156 10 false *a
*a Clamp *b Guide



v.

Connect the connector.


vi.

Engage the claws.



b.

for Integrated Type:

i.

Engage the guide and clamps to install the antenna cord sub-assembly.

E451696C02
2.729,2.365 2.104,1.865 2.104,1.865 2.813,1.948 true 4.073,2.448 4.76,2.219 4.76,2.219 4.667,2.604 true 5.583,3.01 5.979,2.792 true 5.469,2.583 5.865,2.365 true 5.344,2.958 5.521,3.135 0.177,0.177 10 true *b 1.844,1.75 2.063,1.917 0.219,0.167 10 true *a 4.802,2.115 5.063,2.302 0.26,0.188 10 false *a 5.906,2.26 6.125,2.427 0.219,0.167 10 true *a
*a Clamp *b Guide



ii.

Connect the connector.


iii.

Engage the claws.



Hide 55972C 11.INSTALL NO. 2 SIDE DEFROSTER NOZZLE DUCT

Hide 55971C 12.INSTALL NO. 1 SIDE DEFROSTER NOZZLE DUCT

Hide 55302C 13.INSTALL INSTRUMENT PANEL SUB-ASSEMBLY